How to install a floor fan How to install a floor fan

Floor fan installation operation method:

1. Clarify the role and location of components.

First of all, take out the assembly parts from the packaging phase of the fan, and look at the instructions about the role and location of each component.

2. Install the chassis.

The first thing to install a floor fan is the chassis, and the installation of the chassis places the support rod at the fixed position of the chassis, and then connects the chassis with the support rod through screws.

3. Install the support lifting rod.

When installing the lifting rod, loosen the fixed parts on the support rod and insert the lifting rod into the support rod.

4. Install the fan control panel.

This is the core component of the fan, during the installation process, insert the control panel into the lifting rod, tighten the screws, and complete the installation.

5. Install the full cover of the fan after the net.

First, unscrew the fixing nut on the rotating shaft connected to the motor, and then put the mesh cover on the fixed position of the motor.

6. Install the fixing nut.

Screw the retaining nut back in the reverse order before and secure the grille.

7. Install the fan blades.

Install the fan blades, align the blades to the fixed position of the motor, and fix them with the accessories that fix the blades.

8. Install the front grille.

Connect the plastic ring of the front and rear grilles, first circle the front grille, and then connect the rear grille and tighten the screws with a screwdriver.

9. Plug it in.

After installation, plug in the power supply and use the floor fan.

If you have a floor fan, you can directly install the base and dry it, and then screw the fan blades to him, and then cover the outer cover after screwing it, which is also very simple.

I think it should be designed very cleverly and then installed.

There are five steps to installing a fan:

1.First, insert the adjustment tube into the base and tighten it; 2.Then install the machine head on the adjusting tube and tighten the set screws.

3.Step 3: Load the back cover of the fan blade into the machine head and tighten it with a fixing nut; 4.

Step 4: Install the fan blades and tighten the set screws (or nuts, note that the fan blade set nuts are upside down). 5.

Finally, install the front cover of the blade and tighten the retaining ring.

Note: When installing the electric fan, unplug the power supply and fix the screws. Non-specialists should pay special attention to the use of tools and personal safety.

Summer is coming, and in addition to the air conditioner, the most refreshing thing is the fan.

Tools Raw materials: floor fans, screwdrivers.

1. Generally, the installation parts of the floor fan are mainly divided into: machine head, base, fan blades, front and rear dust covers, upper and lower connecting rods, etc.;

2. Remove the connecting rod and base, and insert it in alignment with the card slot;

<>3. Turn the base and the lower connecting rod sideways, and borrow the screwdriver to screw in;

<>4. Tighten the upper connecting rod with the machine head, and then dock with the lower connecting rod and tighten it;

<>5. Take the rear dust cover, the "scissor head" is facing up, align the fixing hole and rod, insert the head shaft, and screw in the fixing screw clockwise;

<>6. Take the fan blade, align the groove with the bolt and insert it, and screw in the fixing screw counterclockwise.

The installation process of the floor fan is as follows:Tools Raw materials: electric fans, screwdrivers, fan blades, turning rods, clamps.

1. Disassemble the express and place the parts neatly.

2. Start the installation and install it from the base network.

3. Install the machine head.

4. Install the fan tour group blade, and pay attention to remove the two fixing buckles when installing.

5. Install the back cover, fan blade, and front cover.

6. When installing the fan blade, pay attention to the clamping of the fan blade groove and the rotating rod.

7. Install the fixed clamp.

8. Turn on the power supply and check whether the wind level, shaking head and other functions are correct.

The steps to install the floor fan are as follows:Tools Required: Screwdriver.

1. Disassemble the express and place the parts neatly.

2. Start the installation and install it from the base network.

3. Install the machine head.

4. Install the fan blades, pay attention to remove the two fixing buckles first.

5. Install the back cover, fan blade, and front cover.

6. When installing the fan blade, pay attention to the clamping of the fan blade groove and the rotating rod.

7. Install the fixed clamp.

8. Turn on the power supply and check whether the wind level, shaking head and other functions are normal.