The floor tiles are empty and half of the drum is half, what should I do?

In this case, I think it is better to pry the floor open again and re-lay the grounding tiles, so that this problem can be handled well, or you can use a beauty seam to fill it.

This floor tile can be replaced directly, and then some cement can be laid underneath, so that it can be better fitted, and it can also prevent the floor tile from hollowing.

You can ask the renovation worker to inquire about the cause of the hollowing, and then renovate to avoid other problems in the future.

Wall tiles are widely used in home decoration because they are very popular among homeowners because they are decorative, easy to use, and so easy to use. Although wall tiles are good, if the construction method is not suitable, it will cause the wall tiles to hollow or even fall off. When the tile hollowing in the bathroom, don't panic, let's take a look at the specific treatment measures for the hollowing of the tile in the bathroom.

There are several common phenomena of hollowing tiles in bathrooms and their causes: the first is that the cement mortar under the tiles is not covered and there are obvious holes, resulting in hollowing. There will be noticeable gaps behind the tiles.

This phenomenon usually occurs in the tiles of the walls. The most common is hollow corners. Of course, local gaps are also common.

This phenomenon is often associated with the mason's craft; The second is that there is a thin separation between the tile and the cement. In this case, it is difficult to detect even after the tile has been removed, because the gap is too small to be noticeable after the tile is opened. The occurrence of this phenomenon is generally related to non-standard construction processes.

For example, the water filling time of the tile is insufficient or not soaked with water, so the tile cannot be completely flooded, and the water in the cement layer separates the cement and the tile after the paving; The third is that the tile and cement are good, but there is a gap between the cement and the wall, and it is difficult to find a cracked cement layer in this case. The occurrence of this phenomenon is usually related to the developer's hunger construction process, such as the wall is not accepted, etc.; The fourth is that the walls are empty (except for the kitchen flue and the internal insulation wall), which means that the quality of the house is not very good. It belongs to the developer's problem, and generally everyone looks for the developer.

If only the cement and wall foundation are empty, and only 1-2 bricks are empty, it will not affect the use. It is not recommended to replace it immediately, wait until the brick can be completely removed, and then reglue it with silicone; If there is a large area of hollowing, it should be replaced immediately. However, it is more troublesome.

It was necessary to remove the tiles of the entire wall and redo the base. Therefore, it is advisable to have a professional do it in this situation.

If more than one-third of a wall or floor is hollowed, it means that there is a major flaw in the construction. In this case, it is necessary to first find out the reasons for the hollowing, such as the wall tiles are not soaked in water, the proportion of cement mortar, the wall base is not stretched, the wall base is not brushed, etc., and then the entire tile is pried off, and the targeted re-paving measures are taken.

If the tile hollow drum reaches more than half, you can only go to a professional master to re-get the tile up, and then re-pave, if the hollow drum is too serious, it must be re-paved.

You should put up the hollow tiles and re-add cement or glass glue to the hollow drums.

Then you have to find a professional to pry the tiles open, and then level the floor and then rebuild it.

Tile hollowing, falling off caused by the wall base and solutions: The tile hollowing and falling off caused by the wall base also exist in many places. The specific solution to the hollowing off of the tile drum caused by the base layer of the wall:

The first step is to completely remove all layers of plastering from the base layer, including where sand and hollowing are found. Specifically, it can be cut with a cutter and then chiseled with an electric drill. The second step is to hang the net plastering.

It is required to hang the net twice and plaster the wall three times.

Finally, the repaired wall should be maintained in time to ensure that the strength of the plastering surface is qualified. After the base layer is processed, the tiles can be applied according to the normal process. When pasting tiles, we should also pay attention to the fact that the tiles we choose must choose the corresponding adhesive material according to their water absorption.

If you choose superabsorbent tiles, you can paste them with cement mortar; Tiles with low water absorption must be glued with tile glue.

There are many reasons why ceramic tile adhesive materials cause tile hollowing and falling off. The following points are summarized: the first point is the wrong choice of tile bonding material.

For example, for tiles with low water absorption, we choose to use traditional cement mortar to paste the tiles. The second point is the problem of the tile adhesive itself. For example, we have purchased counterfeit products, or we have not prepared and mixed them as required by the product instructions for tile adhesives.

The third point is that when we use cement mortar to paste, the cement and sand we buy do not meet the requirements. If expired cement or sand with too much mud content is used, the strength of the cement mortar will be seriously reduced, and hollowing and falling off will occur.

If the tile is dented and falling off due to the tile adhesive material, there is a lot of adhesive material on the wall at this time, which is very flat, but the back of the tile is very clean. At this point, a very simple way is to use AB glue to apply these fallen tiles directly. Of course, this can only solve one or two locally dropped tiles.

Large areas of detachment need to be reprocessed, and the bricks are pasted using a formal method. When using AB adhesive tiles, the back of the tile must be sanded, cleaned, and then glued to the tile directly to the wall.

You have to dig up all these bricks, then find a professional engineer, buy another batch of bricks, and have the engineer reinstall them.

Be sure to remove all the tiles and then treat the walls to remove all the gases and make the surface very clean and tidy.

The first thing is to remove all these tiles, and then you should also choose the right size of tiles, be sure to seek professional help when laying them, and pay attention to the humidity of the wall, and you should also pay attention to the technique.

In fact, everyone knows that floor tiles are hollow and falling off in interior decoration are common phenomena. Why are there so many hollow floor tiles today?

The reverse side is not clean, and there is a layer of dirt and ash. Tap water soaking is insufficient. The quality of cement mortar is unqualified. Unreasonable preparation, unreal engineering construction bonding and other factors caused by hollowing and falling off.

Different types of hollow drums have different correct ways to deal with them.

Treatment: grouting to fill the void.

If the hollow drum is generated on the edges of the four corners of the floor tiles, the method of filling cement slurry can be used. The floor tile joints at the hollow drum at the edge of the slurry are scraped. Concrete is synthesized into a very thin and thin cement slurry.

While hitting the hollow drum with a metal hammer (causing it to vibrate), pour cement slurry into the gap (so that the cement slurry slowly spreads over the hollow drum).

Advantages:

This type of solution saves costs and does not easily lead to damage to the floor tiles.

Treatment: pry brick repaving.

If the floor tile is partially hollow, the hollow drum part is generated in the middle of the floor tile, and the floor tile must be removed how to carry out the paving. After the edge hollow drum passes the grouting, there is still a hollow drum and must also be resurfaced.

It is not easy to cause harm to the surrounding floor tiles.

Defects

Because the floor tiles have been damaged, there must be a reserve floor tile of the same model.

Treatment: revise the bottom layer, pave the floor tiles again, the total area of the hollow drum "1 3 The total area of the floor tiles, all the bricks must be removed, and the bottom layer will be dug up again and then paved with floor tiles. Generally speaking, large-scale hollowing is caused by unreasonable installation.

Treatment: Cement slurry again.

If the hollowing degree is more serious, the floor tiles have been completely loosened, indicating that the cement mortar layer under the floor tiles and the bottom layer of the pavement have also been loosened, and the cement mortar layer can be removed with special tools such as ash knives, and the cement mortar is wiped again and the floor tiles are paved. If the floor tiles are only partially loose, do not hit the cement mortar on the basic surface vigorously to prevent the solid floor tiles from being loosened.

Solution: Able to no longer be resolved.

If there is a slight hollowing of the floor tiles on the wall pavement, such as the baseboard on the fabric sofa, the unloaded floor tiles in the corner of the room, and the bed underneath, it can be considered that there is no need to repair it. Or whether it is harmful to the installation of kitchen cabinets, basin cabinets, shower heads and electric water heaters, or whether the parts are in the kitchen cabinets and hanging cabinets and other furniture, the hollow floor tiles have cabinet boards against the porcelain will not fall, and you can also choose to avoid the solution.

First, first take out the hollow drum tile, and then clean up the base and the back of the tile, it is recommended to use fast and good mildew super sealing structural adhesive or strong liquid nail 300ml on the back of the tile, using multi-point distribution as well. Finally, level with a rubber hammer.

Second, the construction method:

Base surface treatment: Remove oil, dust and loose objects from the work surface, clean tile crevices, and ensure that there is no debris and water accumulation.

Stirring: Pour the dry powder into a container containing 27%-29% water in a certain proportion, stir at low speed with an electric mixer, stir while pouring the powder until the thick slurry (like paste) with no granulation and precipitation is uniform and free of granulation and precipitation, and then stir for 1-2 minutes before use.

Caulking: Use a professional caulking tool to completely press the caulk into the gap diagonally, taking care not to leave it empty. After 10 minutes, wipe off the caulk from the tile surface with a damp sponge or cloth.

Cleaning: After the caulk is dry, use a wrung out wet sponge to clean the surface of the tile. Try to avoid strong direct sunlight for 3 days after construction, and it is recommended to sprinkle and maintain the construction of the caulking material every day for a week.

It is very good to fill something in the hollow area and use some glue to glue a tile in the place where it falls off.

In such a situation, the tiles should be re-laid, and they must be laid stronger, and professional workers should be asked to lay them.

When encountering such a thing, you can only go to the tile again. It can be well avoided, and this situation will not occur.

Faced with such a situation, you should find a professional decorator to help you repair the hollowing and falling off of the tiles. It is also necessary to choose some more reliable materials.

Generally, it is dismantled and re-paved, and it can be used to remove bricks carefully.

Since it has been confirmed that the hollow drum has reached half, it is better to re-attach all the tiles if the local repair effect may not be ideal, first knock out all the tiles, and then re-level the base surface to ensure that the base surface is flat and firm, free of oil and dust, etc., and then use tile adhesive to bond. Here's how to do it:

1. Pour the porcelain sticker powder into clean water and stir it into a paste (mixing ratio: 20kg powder 6kg water), after stirring, it needs to stand still for about 10 minutes, and then stir slightly before use, which helps to increase the adhesion force.

2. Use a toothed scraper to apply the glue on the working surface to make it evenly distributed and form a toothed shape.

3. Knead the tiles on the top during the drying time.