How to make simple crafts from toothpicks

Make a house with a toothpick by hand:

First, use wide transparent tape as the base, the kind of sticky cardboard box, with the sticky side facing up, so that the toothpicks can be lined up on top.

Second, divide several toothpicks into a cross and staggered with the lined toothpick wall, so that the wall is reinforced.

Third, paint the toothpicks arranged in the above two steps with 502.

Fourth, wait for 502 to dry, then pick up the transparent tape, the side of the toothpick wall is facing down, use a hair dryer to melt the soft glue on the transparent glue, and the toothpick wall will fall down by itself due to gravity.

Toothpick handicraft production method, as we all know, toothpick belongs to the three-dimensional composition of hard wire, the basic ones are, frame structure, base structure, mesh structure, tensile structure, thread weaving surface, etc.

Prepare tools: ruler, ruler knife, paper towel, milky white glue, 502 glue, small brush, a bottle of wooden paint.

First of all, you brush the top of the paper towel with a small brush with milky white glue, and then paste a toothpick and mark it with a ruler to make a toothpick version. Note that if the amount of milky white glue is too much, the whole toothpick will be stained with glue, which will affect the texture. It also affects the degree of aesthetics.

The toothpick version is made, which means that the walls of the villa are finished, make two toothpick plates, then tear off the excess paper towels, align the two toothpick plates, (up and down) and then press the toothpick version with a ruler.

Cut diagonally at 45° with a ruler knife, and after cutting, put the two 45° angles on each other, so that the corners of the wall are made, which looks beautiful.

If you want to make it simpler, you can use toilet paper.

First calculate how big the toothpick room you want to make, for example, the wall around the house is 18 cm, just take down 18 cm of toilet paper and then stick toothpicks on it, one by one, after pasting 18 cm, connect the head and tail, and use a toothpick to put it horizontally inside, so that the wall is made around it.

Or instead of paper, you spread the toothpicks horizontally into a plate, and then brush the milky white glue, and lay a row of toothpicks vertically on the milky white glue.

1. First prepare the materials for making crafts: a bag of toothpicks, glue, a knife, a ruler, and sandpaper.

2. Place the toothpicks side by side on the glass or steel plate, otherwise it will be difficult to pick them up. About ten toothpicks are good, and they are glued with glue drops.

3. For aesthetic reasons, take the middle section, cut out the length of two centimeters, and polish the two ends with sandpaper to smooth it.

4. Use a toothpick to cut out a 45-degree angle to do a good edging, and pay attention to leaving a chair for later chairs.

5. A circle of edging should be done around and below, but attention should be paid to the position of the chair legs.

6, Then we glue the chair legs to keep the whole chair balanced.

7. Finally, stick the backrest according to the figure below, so that the handicrafts made of toothpicks are ready.

You can use a toothpick to make a small chair. Prepare materials: toothpick, knife, ruler, 502 glue. The specific steps are as follows:

2. Then use 502 glue to glue the toothpicks side by side, paying attention to aligning the two ends.

3. Make a chair seat. Leaning on the bottom of the already glued row of toothpicks, use a knife to cut out a square chair seat with a side length of 2 cm.

4. Make the edge part of the chair. Pick a toothpick with both ends and cut out the shape as shown in the picture, cut out the shape as shown in the picture with one end of the two sticks, and glue it horizontally around the chair seat, taking care to leave one side for the installation of the chair legs.

6. Finally, install two long and two short legs at the position of the chair legs reserved above, and such a delicate small chair is made.

Materials required: 10 toothpicks, a bottle of white latex, a pair of scissors, a thread shaft, and a piece of foam.

Specific steps: 1. First of all, prepare several materials to be used.

2. Cross the tops of the two toothpicks first, insert them into the foam, and glue the intersection points with white latex.

3. Less than the distance of one toothpick, cross the other two toothpicks, and the top is also crossed and glued.

4. Put a toothpick on the two intersections, and also glue it with white latex and four crossed toothpicks.

5. Take the other five toothpicks and cut off the tips with scissors.

6. Each one is divided into two, and every five is glued in a row with white latex, and the two rows are at an angle of about 135 degrees.

7. Take a section of line, fold it in half into a double line, and divide it into two sections.

8. One end of the section is hung on the left side of the toothpick at the bottom of the section. The other three threads also go around the toothpicks at the top and hang on the toothpicks at the four corners of the swing.

9. Adjust the two lines to the same length, and then glue the threads on the four corners as the rope of the swing.

10. Adjust the position of the line on the beam so that the seat of the swing is placed at the most comfortable angle. A toothpick swing is done.

Toothpick rocking chair.

Required Materials: Toothpicks, transparent glue, scissors, glue.

Production steps: 1. Now make a sitting board, measure the size and write it down, (you can stick the wooden stick on the gelatin, drip 502 and so on, and then remove the transparent glue.) can reduce the chance of 502 getting into your hand).

2. To make a backrest, it should be consistent with the length of the seat.

3. Dip the seat board to the backrest.

4. Make handrails.

5. Make a rocking chair, and the part of the rocking, the wooden stick should be baked on the fire and bent it 6. Make the support for the backrest

7. Glue together and finish.

Use your fingernails to gently make the toothpick into a curved It can be successful, I often do it, and then color it with acrylic paint, then grab a small handful and tie it up with a rope, glue the bent toothpick, insert it in the seam of a small handful of toothpicks and stick it around the outside, and then a flower will be fine, but it may be a little prickly

You can take a piece of paper with a hard texture and stick a toothpick on it, and as for what kind of picture you want, it's up to you, and see what you can glue, and I've done something like this before, but it's not a toothpick, but it's pretty much the same.

You can put them in the shape of a basket.

You can make caterpillars with children, and use soft things to bend your teeth to make caterpillars' feet, which is very fun.

If you are strong, you can try to learn to carve Yue Fei's "Man Jianghong".

1. Use wide transparent tape as the base and arrange the toothpicks on it.

2. Divide several toothpicks into two and arrange them in a cross with the lined toothpick wall.

3. Apply the toothpicks arranged in the above two steps to 502.

4. After the 502 is dry, pick up the transparent tape, so that a small house made of toothpicks will be formed.

A toothpick is a small wooden stick or bamboo skewer that is used to remove debris from between your teeth. Toothpicks are an important oral hygiene appliance that has been around for more than 2,000 years. Due to its small size, it is usually made of wood or bamboo.

1. First of all, the forklift sends a large number of cut logs to the factory, and these wooden stakes are the raw materials used to make toothpicks.

2. Next, use the mechanical claw to put the heavy wooden stakes into the debarking machine. The bark is one of the indispensable processes for making toothpicks, and the peeled bark will be used as fuel in Jinchang by selling it to a nearby factory. The skin of the stake is sanded twice by the debarker until it is processed into a standard cylindrical timber.

3. Next, the processed wooden pile is sent to the next process. The hobbing machine cuts the stake into the shape of a paper roll and divides it into 12 uniform planks, each millimeter thick and centimeter wide. Eventually, these cut strips will be rolled into multiple bags by this roller.

4. Next, place the wooden strip roll on this punching machine, and this machine will automatically complete the work of cutting strips. The air conditioner's cutting speed is very fast, the blade can cut 2,000 times per minute, and 8,000 toothpicks can be cut in just 60 seconds. The cut toothpicks fall into the chute below and into the container, but they are still soft, so they need to harden and dry in a 121-degree oven for four hours.

5. Then the toothpicks are fed into the grinding equipment for polishing, with the aim of making them more delicate and smooth. This process takes about four hours to complete. Once sanded, the toothpicks now go into the sieve bucket to filter out the damaged toothpicks, while the intact toothpicks are sent to the automatic packaging machine via a conveyor belt.

The counter first counts the number of toothpicks, and then the device opens the box and lines it up to be filled. The packaging machine then automatically completes the filling process.

Handmade materials made of toothpicks: toothpicks, white latex or super glue, cardboard or foam acres imitation board.

First, use a wide transparent tape as the base, the kind of sticky carton, with the sticky side facing up, so that your toothpicks can be lined up on top.

Second, divide a few toothpicks into a cross and arrange them in a cross with the lined toothpick wall, so that the wall is reinforced.

Third, paint the toothpicks arranged in the above two steps with 502.

Fourth, after the 502 is dry, you pick up the dia-telecommunication cryptofiber gelatin tape, the side of the toothpick wall is facing down, and use a hair dryer to melt the soft glue on the transparent glue, and the toothpick wall will fall down by itself due to gravity.