The renovated house does not have a reserved network cable, can you still arrange the network cable?

Yes, the network cable can be open-line, if you feel that the surface-mounted network cable is not beautiful, you can also install a wireless router.

However, the signal of wireless is a little worse than that of wired.

If there is no tube on the ground, you can only walk the bright wire, you can only use the wireless if you can't accept the open wire, and you can only use the power network if you can't accept the instability of the wire, so you can only use the power network, that is, the network data can be transmitted through the wires that have been armed, and the speed and stability are not as good as the network cables, but you don't need to rewire. Power cats need to be purchased in pairs, and the higher the speed, the higher the **.

If the network cable is not reserved but the line pipe is reserved, it can be put out in the later stage, if there is no open line, it will affect the appearance, and the wireless coverage of the whole house can also be considered.

Of course, you can rearrange the network cable, such as the dark pipe with the penetration, you can only lay the open line. If you use the footboard or the wall to draw the border, it is also beautiful.

The renovated house does not have a reserved network cable. If your house has already been renovated. Some houses do not have internet cables. Then you, either you go wired, you can only go to the bright line, or you go wireless, through wifi coverage.

I think that even if the renovated house does not have a network cable, then it can be directly taken from other places, and the staff who installed the network cable will solve this problem for you.

There is no network cable reserved for house decoration, so you can only take the bright line. If you feel that the bright line is aesthetically pleasing, then you have to consider using a wireless network.

Since the house has been renovated and there is no reserved network cable, it has to be installed open. Now there are small clips on the surface-mounted line in online shopping, and the line is also very beautiful.

It means that you did not plan and design before the decoration, and now that the decoration has been completed, you want to pull the net line, in addition to the most convenient to take the bright line, it is quite troublesome to re-route the network cable and then control the wall to punch holes.

In this case, you only need to hook the network cable into the cable trough with wire, and then you can pull the network cable for each room.

I think you can choose to leave the cable on the outside instead of inside. If you then get the network cable into an acquisition box, it won't be particularly unsightly.

The best thing to do is to walk a bright line on the wall and fix it with nails.

After the house is renovated, there is no network cable, what is the remedy?

Hello Li Beichun, 1. Layout with bright lines; Directly use the bright line, and try to make up for it in the layout, such as placing the bright line behind each cabinet and desk as much as possible not to show it, and decorate the one that appears, but it is still very beautiful, and the appearance will still be much lowered; The good thing is that the signal loss of the network cable transmission is low, the stability is good, and the network speed is also stronger. 2. Wireless transmission; After broadband access, install a wireless router wireless AP (the strength of the roll-off wireless router should be sufficient, if not enough, add an AP router bridge), cover the entire area of the home with a wireless network, and install a wireless network card on the desktop to access. The disadvantage of this is that the network speed and stability are relatively weak, and it is not recommended for high network speed requirements.

3. an electric cat; The power modem is divided into one main and multiple sub-routes, and the main router and each secondary router are paired. The main router is connected to broadband, and then the secondary router can be directly plugged into the electric plug of each room, which can be used at any time, and can be independently controlled according to the layout of the room, and the wireless network can be basically covered, and the LAN port on the power cat can be connected to each terminal; This method is between the open line and the wireless, the stability and strength of the network transmission are not as good as the network cable, but it is better than the simple wireless transmission, and the aesthetics will not be affected, and it is relatively appropriate in the case of using a higher quality power cat. In short, it is mainly based on the actual situation of the individual, according to their own needs and environment, to reasonably choose the most cost-effective one.

Super Cat5e network cable, copper core, the outer skin will be marked with the CAT5E logo, generally used in 100 Gigabit network, mainly cheap, and now there are many people who use it. When decorating weak current wiring in a home, you must first make a comprehensive plan. Specifically, this plan includes, the optical modem is placed, the wireless router is placed, and each room needs to pull a separate network cable.

The first type: full coverage of home wireless, such as full coverage of the whole house WIFI-5G. However, at present, the signal through the wall is unstable and stable, and sometimes the signal is very weak and the data transmission is unstable.

It may be necessary to set up wireless routing in every room to ensure signal quality, which is not reasonable. The space of the weak current box is narrow, and it is not suitable for routers, switches and other equipment, which will cause heat dissipation problems and wireless wifi signal shielding problems.

My family bought a second-hand house, and the previous homeowner ignored this problem. The network cable that leads to the whole room is only the living room and the study have a network port. Therefore, in order to allow each room to be connected to wifi (because every room has the possibility to connect to the network box to watch TV), a network port bridges the optical modem dial-up, a network port to the router and plugs back the switch of the weak current box to achieve high-performance network access to the whole house, plus wired seamless backhaul, and the last network port is reserved for iptv This solution will take all in the next 5 years!

It is necessary to pre-embed the network cable in each room, which is still very convenient, because you can use the network cable in every room, and there will be no trouble.

There is no need to embed a cable anymore, because most homes use high-power wireless networks, and every room can receive the Internet.

It is not necessary, and it is very wasteful to have a cable embedded in every room.

Is it still necessary to wire the network cable for home decoration? Is wireless wifi bad?

When decorating, it is not necessary to install network cables, you can install network cables after decoration.

It is necessary to install a network cable, because the network cable is what we need in our daily life. So it is necessary to install it.

Of course it's necessary. Because families are now inseparable from the Internet, it is very necessary to install network cables.

The installation of network cables is an indispensable part of the decoration of new houses, and it is necessary to install network cables during renovation. Different scenarios require careful preparation in advance.

Nowadays, new houses have weak current design, usually there are weak current boxes in the house, in the dining room, living room, corridor on the walls of these spaces, there are two electric boxes, the high part is a strong current box, inside is the electric switch and wires; At the bottom is the weak current box, which is the TV line network cable, ** line, line tube, and a strong electrical socket. If the weak current has not been changed during the decoration, the original weak current pipeline and plug-in board are retained, and the network cable can be threaded through the weak current box.

Conduit threading. Usually the inside is threaded with a good network cable, if there is no threading, you can ask an electrician to thread the wire, use the wire to penetrate the wire first, from the socket to the weak current box, and then use the steel wire to pull the network cable into the wire pipe. There are also stringing machines, but they are rarely used for home improvement. In order to buy a machine for threading cables, it is not suitable, you can choose a stringer or rent or borrow an electrician stringing machine.

If you wear it well, you can replace it with the original cable towing network cable.

In addition, it is an old house, with no ** line and network cable, and no weak current design. This can only walk the bright line, and the open line can be passed on the baseboard, along the baseboard, and the door sleeve line. If the baseboard is hollow, you can walk the network cable into the baseboard so that the network cable can be hidden.

Or go to the top surface and hide the network cable in the top corner line by installing the top corner line. If there is a suspended ceiling throughout the house, it is also possible to thread it from the ceiling.

Or use stainless steel trunking for installation, which can be used as a wall top decoration. Personal opinion, welcome to correct the exchange, if you think it makes sense, please feel free to like it and then go, thank you!

If you don't have a network cable, then you can only install a router at home with good wall penetration, and then match a wifi signal relay point, so that you can cover all the signals at home.

The network cable can be threaded through the weak current box. Usually the inside is threaded with a good network ** cable, if there is no threading, you can ask a professional electrician to thread it, or you can directly find a broadband company.

Take the bright line. Pull in a mesh cable from the outside and place it on the wall, and you're good to go.