How to remove the Sail 3 seats, how to remove the rear seats of the old Sail

1. First, press the button under the seat of the SAIC-GM Chevrolet Sail 3.

2. Below you will see the fixing screws of the SAIC-GM Chevrolet Sail 3 car seat, remove it.

3. In this way, the cushion of the SAIC-GM Chevrolet Sail 3 car seat is removed.

4. Next, remove the fixing screws on the backrest of the SAIC-GM Chevrolet Sail 3 car seat.

5. Finally, take a look at the seats of the SAIC-GM Chevrolet Sail 3 car and remove it.

First, the disassembly method:

On both sides of the head of the rear seat, near the window, there will be handles, pull the handle, the backrest of the rear seat can be turned forward, and most of the cushion parts of the rear seat are squeezed directly to the rear of the car, and then lifted up to come out.

Second, the rear seat lifting method:

1.Under the heads on both sides of the rear seats, there is a switch to push forward after pressing it, 2Foldable backrest, open the rear trunk under the seat (if you can't see it, it may be pressed under the seat) There is a black strap to pull back and lift the seat up, 3

Attach the hook to the front seat header and adjust the strap.

Start by lifting the two ends of the front of the saddle upwards.

Allow the front of the saddle to pull out of the two card slots.

Folded down the backrest again.

Lift the U-buckle in the middle of the back of the seat cushion from the hook.

At the same time, it is easy to pull out the rear seat cushions.

Put back the steps on the contrary.

1.Open the trunk; 2.the innermost side near the seat; 3.One screw on the left and one on the left; 4.Remove the screws with a tool; 5.Open the back seat cushion; 6.Pull the backrest forward and pull it away.

This is all with screws, and it is possible to disassemble it directly.

1. First, press the button under the rear seat of the Chevrolet Sail, so that the fixing screws of the rear seat can be exposed.

2. Then remove the fixing screws of the rear seats of the Chevrolet Sail.

3. Then you can remove the rear seat cushion of the Chevrolet Sail.

4. Next, remove the fixing screws of the rear seat backrest of the Chevrolet Sail.

5. Finally, you can remove the rear seat of the Chevrolet Sail.

Sail. Rear seat reclining method: There is a thin rope on the side of the rear seat, which can adjust the backrest angle back and forth by pulling it, and the rear seat is connected to the trunk to form a platform by pulling it down.

Proportional reclining of the rear seats means that the wheel backrest of the rear seat can be reclined proportionally, compared with the overall reclining of the rear seat, the flexibility of reclining proportionally is higher, and only half of the backrest can be folded down to place large items, while the part that is not reclined can still sit people. The common rear seat reclining ratio is 2 proportions.

1 3:2 3 Ratio Reclining: Generally appears in the back row with three seats, and can be folded down two seats on one side or one seat on the other side.

1 2 Proportional Reclining: Generally appears in the back row with two seats, and one of the two seats can be reclined down.

The seat must be properly adjusted when driving. When riding, keep the hip guard as close back to the backrest as possible. Adjust the distance between the seat and the pedals so that your legs are slightly bent when you pedal.

The passenger seat should slide back as far as possible. To adjust the headrest upwards, pull the headrest upwards to the appropriate position. If you want to pull out the headrest, you need to press the release to open the tomato off.

To adjust the headrest downward, press the release switch and push the headrest down to a suitable position and release the release switch to fix it. When riding, lean your shoulders back as far back as possible. Set the backrest tilt so that you can easily reach the steering wheel with your arms slightly bent.

When turning the steering wheel, keep your shoulders resting on the backrest. (Photo by Zhang Xia1) @2019

1. First of all, break the gap between the seat cushion and the backrest of the rear seat of the SAIC-GM Chevrolet Sail car by hand as shown in the figure below.

2. Then you can see the fixing screws of the rear seat of the SAIC-GM Chevrolet Sail car.

3. Next, use a tool to remove the fixing screw on the left side of the rear seat of the SAIC-GM Chevrolet Sail.

4. Then remove the fixing screw on the right side of the rear seat of the SAIC-GM Chevrolet Sail.

It should be from the inside of the trunk, there are two fixed nuts inside, and the backrest of the nuts falls off, and there are screws under the seat and in the gap between the table mat.

Remove the seat cushion and see that there are screws under the backrest, remove it and lift it up and down.

Let's go to the repair shop. It's more difficult to dismantle yourself.

1. First take out the rear seat cushion of the Chevrolet new Sail and put it in, as shown in the figure below

2. Next, install the chuck of the rear seat sleeve, as shown in the following figure:

3. Then install the buckle and clamp the elastic band, as shown in the following figure

4. You only need to adjust the position of the cushion again, as shown in the figure below

5. This is the rear bench of the vehicle, as shown in the figure below

6. Next, you need to press out the handrail to prepare to set in, as shown in the following figure:

7. When pushed into an oblique angle, then put in the vehicle armrest seat cover, as shown in the following figure

8. After installation, push back the handrail of the vehicle, as shown in the following figure

9. Then snap the originally installed backrest buckle, as shown in the figure below

10. In this way, the rear seat cushion of the Chevrolet new Sail is installed, as shown in the figure below

3 All Chevrolet Sail 3 rear seats can be folded, the folded rear seat will greatly increase the storage space of the vehicle's trunk, and the rear seat of the car needs to unlock the lock switch of the backrest, and then it can be put down, the specific operation steps are as follows:

1. Open the Chevrolet Sail 3 driver's door.

2. Pull up the hand brake of the Chevrolet Sail 3 to avoid slipping.

3. Open the rear door of the Chevrolet Sail 3.

4. Unlock the rear seat latches of the Chevrolet Sail 3.

5. Move the rear seat headrest of the Chevrolet Sail 3 to recline the seat.

Hello, the seat of the Chevrolet Sail III can be put down, but not flat, there is some reclining.

Hello, the rear seats of this Chevrolet Sail can be put in, but they can be placed forward, and they can also be taken down.

For the Chevrolet Sailo III, this rear seat should be said to be non-reclining, and this angle cannot be adjusted.

The rear seat backrests of the Chevrolet Sail III can be reclined, but they will not be as flat as the seats.

Hello, the rear seats of this car cannot be reclined, and his rear seats are fixed.

The rear row of this car can be reclined, the practicality of this reclining is still good, and it is easier to install the seat cushion.

Its seats are reclining. But he put it slanted, not flat. You can take a look at the instructions for a detailed introduction.

How to disassemble the new Sail rear seat, first open the trunk, there are two M13 nuts on the back of the seat backrest to remove it first, then turn the backrest forward and lift it up to take off the backrest, take off the backrest and you will see that there are 2 screws underneath, and then there are 2 screws on the floor, remove all the screws with a socket wrench, and then you can remove the seat.

Chevrolet New Sail is a new product created on the basis of the original Sail by Shanghai General Motors for the actual needs of Chinese family cars, and in terms of configuration, the Sail 3 Manual Comfort Sunroof Edition has added a sunroof and automatic start-stop system on the basis of the entry-level manual ideal version model.

Chevrolet's new Sail adheres to Chevrolet's global product design concept and caters to the priority consumption needs of Chinese sedans, with high quality, large space, high safety and low fuel consumption. It is built for the majority of well-off and happy families in China. They are a simple and pragmatic group of people who pursue family happiness, are willing to enjoy simple and real happiness, and seriously and pragmatically pursue the steady improvement of their quality of life.

For them, safety, fuel consumption, space, quality and cost are the core rational demands of automobiles. With high quality, large space, high safety and low fuel consumption, the new Chevrolet Sail came into being. (Photo by photo:.)

Miaoling Chen) @2019