How to clean the practice sign on the sticker

Before removing the logo sticker from the front windshield, you can cover it with a hot towelLogosSoak and when it's soaked, some of the stickers can be easily removed. In addition to a hot towel, you can use soapy water orLaundry detergent waterSoak it in the same way as a complete removal. If you encounter a long-lasting, sticky sticker, you can use a special cleaning solution to remove it.

If the front windshield is affixed with a solar film.

You can use a towel dipped in a small amount of alcohol to wipe the label repeatedly, but never spray it directly on the glass, otherwise it will damage the car film.

It should be noted that whether the front windshield is pasted with or without solar film, you cannot use sharp objects such as blades to remove the logo sticker, otherwise it will scratch the glass or solar film, and all kinds of discarded membership cards and ** cards are good tools.

The physical removal method is actually very simple, and almost every tool is available, which is a hair dryer used for hairdressing. If possible, use a long plug-in board to direct the power supply outside, plug in a hair dryer, and use hot air around the signage sticker.

Heat back and forth, and in a short time, you can easily uncover all kinds of identification stickers.

Use. Probationary drivers should display the probationary sign when driving.

placed in the rear window of the car.

The conspicuous position of the glass or the rear of the body, after other vehicle drivers see this sign, they can take avoidance measures in advance to obtain the understanding and care of other vehicle drivers, pedestrians and traffic police to prevent traffic accidents.

Just change the glass, whew.

Diluents are the fastest and most effective depigmenting products.

There are benefits for novices to stick, and others will let you order when you drive.

Preparation tools: plastic shovel, adhesive remover, rag.

Solution: Step 1: Use a plastic shovel to start from the edge of the sticker and slowly lift the sticker off the body.

Step 2: Tear off the sticker completely after a large gap appears.

Step 3: Apply an appropriate amount of adhesive remover to the remaining blot of the sticker, apply evenly and wait for a few minutes.

Step 4: Use a clean cloth to dip the adhesive remover into the stain and wipe it slowly.

Step 5: After wiping for a few minutes, the sticker marks on the body will be completely removed.

Novice drivers can pick up the new logo free of charge at the DMV or any branch.

The standard style of the internship logo is a teardrop shape, and the font for the word "internship" is in bold 250-point italics, with the main color yellow and the orange color scheme. Formal internship signs can generally be obtained at their own driving school or local vehicle management office, or they can be printed by themselves, but you must pay attention to operate in strict accordance with the specifications.

Precautions for driving in the car.

For many EFI vehicles, when the vehicle opens the ignition key, the driving computer will carry out computer self-test to eliminate potential safety hazards when driving, and its inspection items generally include ABS, braking system, lubrication system, ESP system and so on. The time of the car computer self-test is generally relatively short, about three or four seconds, at this time it is best not to start, and then start the vehicle after the instruments are normal.

When playing the left turn signal, you mainly look at the left rearview mirror, when you play the right turn signal, you must always look at the right rearview mirror, and you must always observe the situation on both sides of the body in the left and right rearview mirrors when overtaking.

Can be through the wind oil essence.

The best way to clean laundry detergent, self-adhesive remover, etc. is to clean it with wind oil essence.

1. Cleaning the internship mark is actually clearing and pasting the internship mark.

of glue marks. Because the ingredients of wind oil essence contain eucalyptus oil and methyl salicylate.

The esters are organic solvents that can dissolve organic substances such as glue marks. For specific use, you can first drop a few drops of wind oil essence on a dry cloth, and then gently wipe the glue marks, you can remove the glue marks of the practice logo.

2. Laundry detergent because of surfactants.

of osmosis, emulsification.

diffusion and dissolution, so it has a good effect on the removal of glue marks. Therefore, you can also use water with laundry detergent and wet a towel to wash the adhesive marks after the practice label or use a remover.

Both sides are acceptable, and there is no special rule on which side it must be posted.

Internship Logo Requirements:

1. The internship logo is pasted or hung in a conspicuous position on the rear window glass of the car or the rear of the body.

2. There are two internship logos, one sucker type internship logo and one magnetic internship logo. Among them, the suction cup type practice sign is adsorbed on the inside of the rear glass window of the car, and the magnetic practice sign is directly adsorbed on the rear shell of the car. All you need to do is stick or hang one of these two logos.

Precautions. 1. Place the internship sign correctly. When using the internship logo, novices should place it in the correct position, that is, in a conspicuous rear of the car or the rear window.

2. Clean the reflective surface of the practice logo frequently. If the reflective surface of the practice sign is used for a long time, it may reduce the reflection effect and affect the reflection effect, so it should be cleaned frequently.

3. Novices must post the internship logo! Novice drivers must put up a probationary sign when they first hit the road, otherwise they will violate traffic laws.

There are two types of internship logos: one with magnetic adsorption and the other with suction cups.

The practice logo of magnetic adsorption is directly adsorbed on the rear shell of the car;

The suction cup-style practice logo is attached to the inside of the rear glass of the car.

The practice sign is only specified to be pasted on the back of the car, and the specific position of the car owner can choose freely, but it must be eye-catching, such as the rear window glass of the car or the rear of the body, so that other vehicle drivers can see this sign and take avoidance measures in advance, so as to obtain the understanding and care of other vehicle drivers, pedestrians and traffic police, and prevent traffic accidents.