If the old vitrified bricks are not removed, it is not possible to paste the vitrified tiles with ti

Yes, but pay attention to the following steps: renovate the wall and floor tiles, first remove the dust and dirt on the surface of the old tiles, and then use tile adhesive to do the base layer on the old tiles, and you can directly paste the new tiles after the completion of the plastering. Remember, the adhesive should also be applied to the back of the new tile, and the thickness should be based on the covering of the back of the tile, so that the new tile sticks more firmly.

When paving new tiles, tap the new tiles with a rubber hammer, adjust them while paving the welts, you need to pay attention to reserving expansion joints, 24 hours later, wait for the tile adhesive to dry thoroughly, and use the grout to hook the joints. It should be noted that if there are serious bulging or damaged tiles, they need to be removed, and after the removal of cement or special repair agent to fill the vacancy, and the surface of the old tile is as smooth as the old tile, and then paste the new tile with tile adhesive, so that it can be firm.

Ceramic tiles are divided into semi-porcelain and all-porcelain, and only all-porcelain can be vitrified. Semi-porcelain paving must be blistered before (if you don't soak it, the semi-ceramic tile will quickly absorb the moisture in the mortar so that the mortar has no adhesion effect), and the all-porcelain paving does not need to be soaked (because of its high compactness). Generally, the wall tiles are semi-porcelain (no matter how good and expensive the wall tiles are, they have to be soaked in water), thinking that the requirements for the pattern, color and brightness of the wall tile glaze are very high, and the all-ceramic can not achieve the ideal effect, and the wall can not be touched during the general use.

Floor tiles are generally all porcelain because all porcelain has good wear resistance and bearing capacity, unless very low-grade floor tiles will appear semi-ceramic tiles (wear-resistant bricks, glazed tiles, semi-porcelain antique tiles). Remember to use water, as long as it is semi-porcelain, it will be sucked, and the whole porcelain will not be visible to the naked eye!

There are many kinds of raw materials used for decoration, mainly including ceramic tiles, pasting ceramic tile auxiliary materials, ceramic tile back glue, everyone does not know much about tile back gluing, the market time is short, one of the ceramic tile auxiliary materials, ceramic tile back glue, there are components and single components, mainly used in pasting wall tiles, the questioner clearly raised such a question: Why must the vitrified tile wall be brushed with adhesive? Tile back glue, is an environmentally friendly decorative material, barrels of turbid liquid, mainly used in pasting different parts of the wall tiles, tile reverse brush back glue, <>

Not only vitrified tiles, other tiles, tiles can also brush the back of the glue, most people only understand the back of the glue, is can paste the tile, really master the tile back glue is not a lot of people, the back of the glue paste tile, not so simple, the specification is quite high. The back-coated glue on the wall flatness is very high, not all walls, can be brushed back glue to paste the wall tiles, the back glue is a barrel of emulsion liquid, the wall leveling is basically impossible, the tile back glue paste wall tiles, determine the wall leveling, even if there is not smooth and uneven, must be solved by cement mortar leveling, master the ceramic tile back glue construction standards, you will understand how to paste the wall tiles with back glue.

Vitrified tile is a kind of ceramic tile, which can also be called a full tile. Vitrified brick is a kind of glazed brick. Vitrified brick is a kind of brick produced by grinding and polishing and polishing on the glazed brick body.

Maybe some friends want to say, isn't that a glazed brick? In fact, the difference between vitrified tiles and glazed tiles is not very big, and one of the big differences between the two is water absorption. Generally speaking, the water absorption of glazed tiles exceeds the following after grinding and polishing, so this kind of tile is vitrified tiles; If the water absorption is above, then this type of tile is glazed tile.

Defects of vitrified tiles. Vitrified bricks are the same as glazed bricks, it has a fatal shortcoming, in fact, it is the problem of the porosity of the internal structure. Because it is a kind of brick produced by restraint, and finally through the grinding and polishing of the appearance, and finally made into a vitrified brick, the gaps in it will never be cleared, only the porosity is a situation.

The appearance of gaps leads to certain problems in the stain resistance characteristics of vitrified bricks. Therefore, the mid-to-late cleaning of this type of tile is particularly critical. Due to the heavy vitrified tiles and low water absorption, the traditional concrete and tile adhesive can not ensure the adhesion of the tile, and the tile will fall off in a certain period of time.

This kind of brick will make the home see that everyone is bright, and it will make the home look brighter, but also to make the light look good. In order to better cross the bridge, it is necessary to brush the adhesive.

Vitrified brick, in the process of modern decoration, the effect of a commonly used ceramic tile will be better, and the waterproof performance is also better, and the brush adhesive is for better bonding.

Posting it will make your home look brighter, and it will also make your home look better. In order to improve the stability of the wall tiles, in order to prevent the wall tiles from falling, but also to prevent the wall tiles from smashing and injuring others.

Vitrified tilesIt is commonly used in the decoration of kitchens and bathrooms, but the paving of vitrified bricks is very skillful, because there are many details in the process of paving, so how to pave vitrified tiles? Below we share with you the paving method of vitrified tiles and daily cleaning and maintenance methods, hoping to provide you with help.

The paving method of vitrified tiles:

1. Before paving, it should be dealt with well to be fitted or the ground is flat, and the base layer of dry paving method can only be paved with a certain hardness, and the joints are mostly adjusted between 2 and 3 when paving.

2. Here Jiuzheng Building Materials Network recommends the use of No. 325 cement, dry paving method participation ratio: rent base layer: cement:

Fine sand = 1:3, paste layer; Cement: fine sand = 1:

2 (white series polished tiles are recommended to be white cement to achieve a harmonious effect). The polished brick is pre-paved with anti-fouling wax before paving, which can improve the anti-pollution ability of the brick surface.

3. If the pattern parquet characteristics are obvious, please look for the unified direction of the parquet features, and the pattern features are not obvious or there is no pattern, please combine the construction effect requirements to pave.

4. After the paving is completed, the cement stains remaining on the bricks should be wiped off in time. The ground that has been paved needs to be maintained for 4-5 days to prevent local unevenness of the ground caused by external forces.

Cleaning and maintenance of vitrified tiles:

In the unused or cleaned vitrified bricks, Jiuzheng building materials network recommends that the surface of the polished brick be coated with a layer of waterproof and antifouling agent, and the water and dirt can not be invaded by silver, and the original bright effect of the vitrified brick and polished tile will never be changed.

For stains on vitrified tiles, you can wipe them off with a clean cloth with a neutral detergent. Sprinkle the floor cleaner on the floor tiles and rub the stains off the tiles with a waxing machine.

Pasting of vitrified tiles:

1. The vitrified brick binder adopts the double-sided coating method, the thickness of the vitrified brick binder is thinly batched at the base layer, and then a layer of adhesive is pressed on the back of the tile, which must be fully filled with the back pattern of the tile, and then paved on the wall after the back of the tile is filled, fully kneaded and pressed, and aligned with the seam. Note that the adhesive application must be full, the adhesive cloth on the back of the tile has no gaps, and the adhesive should be in full contact with the tile and the wall.

2. Paste the vitrified bricks from bottom to top, paste the bottom two vitrified bricks according to the horizontal line, and then paste the pull-through line in turn, with a gap of 1-2mm. After the vitrified tile is laid on the wall, the position of the tile can be adjusted within 10 minutes, and the tile can be flattened with a ruler.

3. When pasting vitrified bricks, a cross plastic frame must be used to leave a 2mm gap between the vitrified bricks and the vitrified bricks, and the joints should be neat and beautiful.

4. The average thickness of the binder is controlled at 5 8mm.

Cement is also available or adhesive 3 mm.

The floor tiles are directly paved with cement mortar, and the wall tiles can be paved with dot hanging (building glue)!

The floor tiles are generally dry pasted, and the ground is swept with cement slurry before pasting, and the gap is generally 1-2mm

The original vitrified bricks are cleaned of the oil stains on the ground with washing powder. Put the newly bought vitrified bricks on it.

When paving the vitrified brick wall, it is recommended that you can first roll a layer of 107 glue on the original blank wall, which is the kind of glue that makes latex paint scraping putty, and then use tile glue, so that the probability of falling off is relatively small. If the bathroom or kitchen wall is waterproof, it is recommended that the waterproof is sanded on the wall before the mortar, which is equivalent to the wall hairing, and the ** below is taken at the construction site, and then the wall tiles are pasted, which can effectively reduce the shedding.