How should a novice white paste wall tiles? What are the precautions for laying wall tiles?

How should a novice white paste wall tiles? Correction; Before laying the wall, be sure to solve the surface of the wall, remove the surface dirt and moisten it with water, and then apply mixed mortar to level the floor. hanging wire; Marking is also an indispensable process before laying the mosaic.

You can start by making a wireframe on top of the plastering layer to develop the marking.

infiltration into the water; It's also important to soak the tiles in water, you can soak them in clean water and then dry them out when there are no bubbles. mixing slurry; If you choose glazed wall tiles, be sure to use cement and gravel and mix them with water at a ratio of 1:3.

What are the precautions for laying wall tiles? The wall tiles should be paved from the top. Pave concrete mortar in areas where there is no leveling.

In addition, attention should be paid to the solution of waterproofing of the ground. The bricks should be leveled, the viewing angle should be precise, and the page should be aligned. Sweep the surface of the damp layer first.

Sets the pavement code elevation. Lay out the large surface layer.

The way of sticking wall tiles: the height line of the road surface is pulled out by the braided wire on the wall, so that the actual effect of better accurate positioning can be achieved. Then let's stick the wall tiles according to the location line.

Hit the surface of the floor tiles with a plastic hammer to build a 1:2 mixed mortar, then spread the floor tiles on the road surface, and then use a plastic hammer to hit the surface of the floor tiles, so that the height and width ratio of the paving tiles is consistent with the relative height of the floor dragged out by everyone, so as to ensure the neat level of the floor tiles.

Dry paving method: dry paste method in the dry paving before wetting and then removing impurities, and then using one to three dry masonry into one to three dry paving, can effectively prevent tile hollowing, blistering and other conditions. But the dry paving method is more time-consuming, time-consuming and labor-intensive.

wet laying; Wet paving is now the most commonly used way to pave floor tiles, and the difference with dry paving is that tap water and concrete mortar replace dry paving.

The use of wet paving method is easy to cause blistering on the surface of floor tiles and hollowing of the wall, which endangers the service life of floor tiles, but the wet paving method is simple to operate, the price is relatively low, and the application is more common at this stage. The basic floor tile is also the most general, the initial way of paving, this kind of method is to pave the side parallel surface, pay attention to the alignment of both ends of the floor tile gap, leave no gap, and then continue to use the caulk with the same color as the floor tile to solve, it looks very fresh.

Novice Xiaobai is not recommended to paste tiles by themselves, tiles need to be soaked in advance, and the ratio of tile glue and cement also needs to be paid attention to, novices are not able to control well.

Novice Xiaobai can choose polished tiles when pasting tiles, its gloss and anti-slip performance are very high, and it is also very wear-resistant; When paving wall tiles, we must first look at the wall tiles, and then go to pave after its grade color difference and whether it is qualified and confirmed, and generally before paving the wall tiles, the tiles need to be soaked in water, so that the firmness will be stronger.

In the process of tiling the wall, the wall must be leveled first, and a certain humidity should be maintained to paste the tiles, and attention should be paid to the waterproof and thermal insulation.

First of all, you need to choose the right tile, then soak in water, choose the right tile adhesive, so that you can better pave, you need to pay attention to the size of the area, pay attention to the arrangement of the tile.

Tile paving should be regarded as one of the most common projects in home improvementWall tile pavingIf it is not pasted well, the tiles will fall off, and it will also affect the overall decoration of the interior. So how to lay wall tiles? Below we will bring you the precautions for wall tile paving, hoping to provide you with help.

How to lay wall tiles?

1. Determine the height, size, and choose the paving method: the first thing to pay attention to when paving wall tiles is to determine the height of the paving, especially in the bathroom, which will prevent the exhaust fan and install the ceiling, so special attention should be paid to the height; Secondly, the size of wall tiles and floor tiles should correspond to each other, and there should not be too much difference; Finally, according to the height, size and the overall effect to determine the paving method, if the unified wall tiles are different, large size tiles from the bottom to the top, small size from the top to the bottom of the paste.

2. Uniform paving and edge closing: when paving wall tiles, it is necessary to pay attention to the level and right angle between each tile, and the sheets need to be kept flat between the pieces; Secondly, after paving, the edge strip treatment needs to confirm the high and low points of the tile and the edge, and the level of flattening and rottenness.

3. After paving, the edge is filled: after paving, it is necessary to confirm the paving effect of the entire wall, whether the color and pattern are wrong, and clean the surface of the tile; After confirming that it is correct, the tile will be caulked.

Precautions for wall tile paving:

1. The treatment of the wall in the precautions for tile paving is also very important, and the wall must be carefully inspected before tiling, and the wall must be treated if there are cracks. In the decoration often will be the wall to scrape putty treatment, if there is no putty shovel off the brick directly, there will be a great safety hazard, putty surface can not hang cement, easy to cause the phenomenon of tile falling off, so in the wall tile paving must pay attention to the treatment of the wall.

2, tile paving precautions in the water soaking to make it the most important step, ceramic tiles regardless of bad will have a lot of fine voids, in use has a certain degree of water absorption, if not soaked in water treatment or soaked water is not enough to pave directly, the tile will absorb the moisture in the cement, which will cause the tile and cement to appear between the connection part of the void, so that the bond is not firm, resulting in hollowing and tile falling off and other problems. When the tile is soaked in water, it is necessary to make the tile completely invade the water, and the time is generally about 30 minutes.

3. In the construction process, do not use and pave tiles in accordance with the regulations. Glazed wall tiles should not be laid on the floor or used as wall tiles for the sake of saving. The physical and chemical properties of different tiles are not the same, such as the water absorption rate of wall tiles and the water absorption rate of floor tiles are different, the wall tiles are high, the floor tiles are low, and their flexural strength is also different.

The above is how to lay the wall tiles for you? The full content of precautions for wall tile paving.

You can put tiles yourself, you can do it yourself. When paving tiles, you need to soak the tiles in advance, clean the walls, and pave the tiles in order, starting from the doors and windows, from bottom to top, and pay attention to grasp the gaps when paving the tiles, and wipe off the excess cement in time.

If you feel that you can lay the tiles, you can do it yourself, which can save a lot of labor costs. But the premise is that your technology must be very proficient, otherwise it may affect the effect of paving, the tiles are warped, the tiles are falling, which will affect the decoration effect, which are very embarrassing rollover scenes. Before paving the tiles, you must first soak the tiles in water, and the soaking time is about two hours, because the tiles absorb water, so they should be soaked in advance so as not to affect the paving effect.

Because we are not professional, just amateur tiles, so we have to learn more from experienced masters how to pave tiles. When we lay floor tiles, we should follow the order of starting from the doors and windows, and if we lay wall tiles, we should pay attention to pasting them from the bottom to the top. When laying tiles, it is best to hang a vertical line, so that there is a horizontal line when laying tiles.

Paving tiles should be in order, according to the steps, so that the effect of tiles can be good.

When laying tiles by yourself, pay attention to the gaps between the tiles and the tiles, and do not leave the gaps too large. When laying tiles, the cement extruded in the middle must be wiped off with a rag in time, otherwise it will be difficult to clean up later, and it is easy to scratch the tiles. You need to use ingenuity to do any work, and you should pay attention to every step when sticking tiles.

Before use, please check whether the product number, color number, and working size indicated on the packaging box are consistent, and pay attention to the classification and stacking for use, if you are not satisfied, please stop the construction, and immediately reflect with the dealer, and ask for on-site inspection, negotiate a solution. It's still best to hire a professional.

This point must pay attention to the whole wall to be very smooth, the second point should also pay attention to the entire wall of some uh partition some distance to take care of, the third point is to pay attention to the tile paving, this thickness is very important, if you want to do it, you need to have a certain skill.

Wall tile paving should pay attention to the cleanliness of the wall, and carefully select the tiles needed to be used, and also carry out pay-off positioning and brick arrangement. It's hard to do this on your own.

In home decoration, there are two common types of tiles: wall tiles and floor tiles. Although both of these are paving tiles, there are still some details that need to be paid attention to in different matters. Let's take a detailed look at the precautions for tiling on the wall and floor.

Precautions for wall tiling:

1. Before pasting the wall tiles, first of all, we must do a good job of grassroots treatment, clean up all kinds of dirt on the wall, and water and moisten the wall one day in advance. 2. Soak the subsidy line of the selected wall macro resistant pure surface brick in water for at least 2 hours, and dry the surface moisture for backup.

3. Before pasting the wall bricks, the bricks should be arranged and positioned, and the non-whole width bricks should be placed in the direction from bottom to top, in inconspicuous parts or corners, and the whole bricks should be laid from the bottom to ensure the decoration effect of the whole space.

Note: There should not be two columns of non-integers on each wall, the width of the non-whole width bricks should not be less than 1 2 of the whole brick, half of the bricks should be arranged at the top, and the width of the brick joints should be between 2mm and 4mm.

4. When pasting a certain wall, it is not advisable to paste it to the top at one time, which is easy to cause the problem of collapse, and the cement mortar should be covered with the back of the brick when pasting the wall brick.

5. In the whole home decoration, it is generally the kitchen and bathroom that need a large area of wall tiles, so because the kitchen and bathroom pipes are easy to deform and cause brick cracks, stainless steel strips can be used at the sunny corner of the wall tiles.

Precautions for floor tiling:

1. Before paving the floor tiles, you need to soak the wet surface with water.

2. Before paving the floor tiles, the thickness of the mortar of the binding layer should be determined according to the design requirements, and the crosshairs should be pulled to control the thickness and the flatness of the surface of the floor tiles. 3. If your floor is paved with stone floor tiles, then you should maintain a horizontal position when paving, gently tap with a rubber hammer to make it bond tightly with the mortar, and adjust its surface flatness and joint width, the joint width is generally between 3mm and 5mm.

4. According to the brick positioning, the paving mortar matching ratio is generally 1:3, and the mortar thickness is 15mm 20mm.

5. For each 10 bricks and about 10 bricks, check the surface flatness and slope with a ruler, and properly adjust the brick joints and keep the bricks clean.

6. When the bathroom is paved with floor tiles, a certain slope should be maintained along the floor drain position to ensure that it does not affect the drainage in the future.

The precautions for the posting of floor tiles and wall tiles are clearly described above, and I hope it will be helpful to you. It must be noted that the position of the wall tiles and the floor tiles are not the same, so they are also different in the precautions for paving, so they must be dealt with separately when paving.

When pasting wall tiles, it is necessary to choose the appropriate adhesive material. Most of the wall tiles at this stage are not traditional glazed tiles. Many friends choose floor tiles for walls.

When we choose the bathroom tiles, we will choose 800 800 tiles, and then the wall tiles are 800 800 tiles to be cut. For example, a tile cut into 400 800, then in fact, this belongs to the floor tiles on the wall. For pasting materials, I recommend that you do not choose traditional cement mortar, but choose a material that is more suitable for you.

The adhesive coating on the back of the tile is actually an auxiliary bonding material, which is mainly used to increase the adhesion of the back of the tile. If we don't choose tile glue when pasting bathroom tiles, we should try to glue the tiles on the back of the tiles and on the cement mortar. The specific operation is to apply glue to the back of the tile and then paste it with cement mortar.

To a certain extent, this can also ensure the sturdiness of our tiles. For the pasting of wall tiles, we must master the method of pasting tiles.

The pasting method of wall tiles generally includes the pasting order and specific pasting method of wall tiles. Because a good tile pasting sequence can ensure the effect and quality of the whole wall tile pasting. This pasting method can also guarantee the quality of the tiles being pasted.

First, the grooves on the back of the bricks are ground off, buried with copper wires, and then fixed with structural adhesive, and then fixed with wooden keels. This laying method is usually used to lay a TV background wall. Generally, the wooden keel is made first, and then the 12cm board is sealed, and then the back of the floor tile is grooved, hung with copper wire, and then fixed.

Wet laying is similar to dry laying but requires the use of cement mortar combined with cement and fine sand to lay floor tiles on the cement walls. Before laying, the walls must be rough to increase the friction before laying. Wet laying takes more time because the tiles take more than two hours to soak in water, the process is more cumbersome, so the labor cost is also more expensive.

Floor tiles are easy to collapse, and problems should be paid attention to in construction. Before laying, check whether the wall is suitable for tiling, check if there are cracks, and if so, correct the wall first.