How to operate and use the floor scrubber? How to use the floor scrubber and precautions

Check the meter to confirm the remaining power before operation, then check the appearance, check whether the cleaning pad or cleaning brush is in good condition, and remove debris and particulate garbage from the floor in advance. After confirming that everything is normal, pull up the solution flow rod, close the solution valve, open the solution tank lid and inject the specified cleaning solution into the machine, and pay attention to the position of the solution while injecting. Reducing the high-efficiency suction and cleaning brushes to the position where they are in contact with the floor ensures that the brushes can fully scrape the floor.

Turn on the switch and the brush starts running, adjusting the solution flow lever to make the solution flow proper and pushing the machine forward. The trajectory of the propelled machine follows a sequence from the outer ring to the inner ring and then from the inside to the outside. Turn off all switches after completing the scrubbing work, if the solution tank is empty, continue to absorb water, make sure all sewage is sucked into the sewage tank, then drain the sewage and solution, flush the sewage tank and solution tank, and prevent the liquid from remaining to block the system after drying.

Finally, lift the cleaning brush and high-efficiency suction brush, wipe the machine shell with a clean semi-dry rag, and move to the charging place to charge after drying.

How to use: The first step is to untie the power cord of the machine, check whether the power cord is damaged and easy to leak, and if it is intact, you can install the needle holder, washing mat or washing brush in the counterclockwise direction at the bottom of the body. Wash the floor that is not smooth, install a special brush, and adjust the handle to the angle that you are comfortable operating.

Step 2: Check and confirm that the machine switch is in a closed state before formal use, and then plug in the power to use it safely.

The third step, the power cord is placed on the back of the machine, hold the handle with both hands, turn on the machine switch, at this time the brush plate or needle plate is kept level with the ground, grasp the lever and go down to control the left and right movement of the machine, when the brush plate begins to rotate, after confirming that there is no fault, start the operation.

Fourth, when working, do not rely too much on your own arm strength to force the group to drive the machine to move forward, backward, left and right, it is best to press the handle to make the machine itself move, and the human body will naturally move with the movement of the machine.

How to use the floor scrubber:

Turn on the key switch, lightly step on the brush pedal, put down the brush plate, put down the water absorption squeegee, press the brush plate and the water absorption switch, adjust the water volume button according to the degree of oil pollution on the ground to adjust the size of the water supply, press the handle control ring down (forward), adjust the speed adjustment knob of the floor scrubber, the floor scrubber can enter the floor scrubbing work, and push the handle control ring up to the machine backwards.

After the work is completed, first turn off the brush button, step on the brush pedal, lift the brush plate, and the machine continues to move forward, when the suction squeegee absorbs all the water on the ground, pick up the suction pickpocket handle, turn off the key switch after turning off the suction motor button and waiting for the machine to stop all functions.

Precautions for floor scrubbers:

1. Read the instructions of the floor scrubber carefully before use, and use it after training.

2. Please do not operate the machine before it is assembled. Before operating the machine, the user should carefully check the integrity of the machine.

3. In the area to be cleaned, the larger debris on the ground and the garbage that affects the suction and pick-up work should be removed first. This is a great benefit for you to increase your productivity and protect your machines.

Fourth, the particularly dirty ground can be repeatedly cleaned or choose different detergents to improve the cleaning effect of floor washing.

5. Due to the unevenness of the ground, sometimes although it has been cleaned, if there is still stagnant water, the brush plate can be raised, the water absorption switch can be started, and the floor scrubber can be pushed to absorb repeatedly and repeatedly in the waterlogged area.

6. There is a deep trench on the ground, which will affect the water absorption efficiency of the machine, please deal with it according to the situation at that time.

7. Usually when the brush plate is in the rising position, do not start the brush plate motor at will, otherwise the brush plate will be automatically removed.

8. When charging the floor scrubber bottle, please make sure that the socket power supply is in good contact, and the charger plug is in good contact with the battery plug.

9. When the battery of the floor scrubber is used for the first time, it should be fully charged. If a large current is used to charge the battery, the charging time may be shorter, but the high current will damage the battery life.

10. When the floor scrubber cylinder is not used for a long time, the battery should be replenished every two to three months.

Introduction: With the development of economic level and technology, we have undergone changes in many aspects. Traditional sanitation cleaning is to take a broom and dustpan to carry out, but in recent years, businesses have designed automatic floor scrubbers for some problems faced in the cleaning process, and the use of automatic floor scrubbers can effectively help us clean a large area, but it is not particularly tired.

So do you know how to use an automatic floor scrubber? It doesn't matter if I don't know, today I will introduce to you the use of automatic floor scrubbers and precautions.

1.Add water to open the lid of the water tank, add water to the clean water tank, add an appropriate amount of detergent, the proportion of addition can be determined according to the degree of dirtiness of the clean environment, and the lid of the water tank needs to be tight.

Note: It is strictly forbidden to pour laundry detergent and high foaming detergent, dish soap into the water tank, the resulting foam will damage or burn the machine!

2.The equipment operates to open the key switch, lightly step on the brush pedal, put down the brush plate, put down the water absorption paddle, press the brush plate and the water absorption switch, adjust the size of the water supply according to the degree of oil pollution on the ground, press the handle control ring, adjust the speed of the floor scrubber, and the floor scrubber can enter the floor scrubbing work; After the work is completed, first turn off the brush button, step on the brush pedal, lift the brush plate, and the machine continues to move forward, when the suction paddle absorbs all the water on the ground, pick up the suction pickpocket handle, and then turn off the suction motor button, and then close the key switch after all the functions of the machine are stopped.

Note: It is strictly forbidden to keep the machine in place for a long time when the brush plate is working, which will cause damage to the ground!

3.Clean sewage treatment of the water tank: push the machine to the sewer mouth and unscrew the sewage pipe cover; Water tank cleaning:

Open the lid of the water tank, first block the air inlet of the fan with a rag to prevent water from invading the inside of the fan and causing damage to the fan, and then rinse the inside of the water tank and the filter screen with clean water. Cleaning the surface of the machine: wipe it with a clean rag.

Note: It is strictly forbidden to flush the fan inlet of the floor scrubber with water! It is strictly forbidden to clean the surface and interior of the machine with corrosive cleaning liquid!

4.To charge, unplug the power supply plug of the floor scrubber, insert the charger plug, and then plug the charger plug into the power outlet. The charging time is generally 6 hours. Brush back, brush up. Lift the brush disc first, turn on the key switch, and press the unbrush button.

Note: It is strictly forbidden to use the automatic brush retract function without lifting the machine head, so as not to cause damage to the machine brush disc and buckle! Place the floor scrubber brush or needle holder in front of the machine, lift the brush plate of the floor scrubber, push it to the top of the floor scrubber brush or needle holder and put it down, turn on the key switch, press the brush button, and when you hear the obvious brush friction sound, close the brush button, step on the brush pedal, and lift the brush plate.

The above is to introduce to you today about the use of automatic washing machine and precautions related knowledge introduction, for automatic washing machine, we use it can effectively reduce their workload, and the cleaning effect is also excellent, but we must operate in accordance with the correct use method, only in this way can we help us achieve the purpose of cleaning the ground, and at the same time can effectively help us extend the service life of our automatic washing machine.

You can get it for free