Zebra ZM400 printer ribbon paper is always Zou, how to solve

In this case, it is mainly a problem of print head pressure.

One is the pressure of the print head.

The second is the pressure of the ribbon shaft and the rewinding shaft.

The problem of print head pressure is relatively easy to solve, release the print head, when re-installing, make sure that the print head is balanced on both sides, and there is no situation that one side is high and one side is low, and then it is installed, loosen the plate in front of the print head, let the carbon take away the paper, after a few sheets, the carbon belt will not wrinkle. Install it.

**shaft, you can adjust the pressure of **shaft to determine. There is a screw on the reel of the shaft, clockwise.

Adjust it counterclockwise and take a look. If that's not enough, you'll have to use a wide ribbon.

Because the narrow ribbon is unbalanced and stressed, the force point is large, which can easily cause wrinkles, but if you change to a wide ribbon, you can evenly distribute the force points to the ribbon, and the force is not so large, and the ribbon will not wrinkle.

Hopefully, this will help you solve this problem.

Ribbon always pay attention to the following points:

Whether the ribbon spindle and compound shaft are mounted symmetrically "in place".

After replacing the ribbon or breaking the ribbon, the ribbon without cleaning the compound shaft is used directly (resulting in uneven rewinding of the compound shaft) Whether the label paper is installed smoothly and whether it is in the card slot.

The quality of the purchased ribbons is not up to standard.

Printing temperature and speed) are too small.

The above (excerpted from: Henan Zhuoyi hot stamping material ****).

1. Determine whether the type of ribbon and the installation are correct, so as to remove the ribbon and reinstall it, or replace it with a new ribbon;

2. There is a problem with the quality of the printer, and the ribbon cannot be detected by the sensor failure, and the sensor needs to be replaced.

3. If you don't want to see this flashing light, the best way is to change the printing mode to the thermal transfer mode.

4. The change of printing mode can be changed on the hardware, and the mode can be converted to TT mode in the setup mode.

Or change it in the driver of the software, if it is printed in the way of instructions, you need to change the source**.

Note: This kind of electronic products is relatively professional, and professional maintenance personnel are required to disassemble and test the machine to avoid unnecessary losses.

First of all, determine the type of ribbon and whether it is installed correctly. (You can remove the ribbon and reinstall it, or replace it with a new roll of ribbon), you can print to prove that there is no major problem with the machine, and observe whether there is any label paper or ribbon residue next to the ribbon sensor.

In this case, it is mainly a problem of print head pressure.

One is the pressure of the print head.

The second is the pressure of the ribbon shaft and the rewinding shaft.

The problem of print head pressure is relatively easy to solve, release the print head, when re-installing, make sure that the print head is balanced on both sides, and there is no situation that one side is high and one side is low, and then it is installed, loosen the plate in front of the print head, let the carbon take away the paper, after a few sheets, the carbon belt will not wrinkle. Install it.

**shaft, you can adjust the pressure of **shaft to determine. There is a screw on the shaft and the reel, clockwise and counterclockwise to adjust it. If that's not enough, you'll have to use a wide ribbon.

Because the narrow ribbon is unbalanced and stressed, the force point is large, which can easily cause wrinkles, but if you change to a wide ribbon, you can evenly distribute the force points to the ribbon, and the force is not so large, and the ribbon will not wrinkle.

Hopefully, this will help you solve this problem.

They all said it, so I'll take a look.

You adjust the pressure of the printhead

1. Check whether the printer driver is installed correctly;

2. Check whether the data cable connection of the printer is normal;

3. If there is a conflict in the system, restart the system or reinstall it;

4. Firewall blocking, turning off firewall or anti-virus software;

5. If the hardware of the printer is physically damaged, if the power board and main control board are damaged, it will cause the machine to fail to turn on, and it needs to be disassembled for detection and replacement.

1.In this case, whether the barcode printer has an error, if the error is reported, you can check the error information on the display screen of the barcode printer, and troubleshoot according to the corresponding information.

2.If there is no error message, check the setting of the printer driver, whether the paper feed option is set to continuous paper labels, change to non-continuous printing and print the test page to print normally.

3.Another special situation is that the label paper roll is too heavy, resulting in the reverse stretching of the paper output is too large, and the printer does not report errors during the printing process, but the position of the print is offset up and down due to the tensile force.

Hope it helps.

1.The thread did not pass the correct path (check by pressing the feed key).

2.The software setting was changed from continuous to die-cutting.

I suspect it's a loose belt, or a slippery belt, so you remove the lid and check it.

The printer does not have a positive confirmation paper, or there is a problem with the software page settings...

Whether your label paper is single-row or two-rowed. Is the barcode in the middle of the top and bottom or in the middle of the left and right sheets? Left and right, it is estimated that the size and actual size of the label paper in your software are not set.

There is also a horizontal spacing to be changed to 2mm. If it's up and down. It is estimated that the printer did not detect the paper.

Just start with a new test of paper.

Zebra label printers bring out ribbons during the printing process and the reasons may be the following:

1.Incorrect ribbon installation: The ribbon may not be properly installed between the printer's print head and pulleys, resulting in the ribbon being taken out while printing. At this point, the ribbon needs to be checked and re-installed to make sure it is properly mated and placed between the printhead and the pulley.

2.Loose or aged ribbon: If the ribbon is loose or aged, it may not be in proper contact with the printhead and pulleys and will therefore be brought out during the printing process. In this case, it is necessary to replace the ribbon with a new one to ensure that it is tight and of good quality.

3.Printer adjustment issues: Improper adjustment of the printer can also cause the ribbon to be brought out.

For example, if the printer tension is set too high or too low, the ribbon may be brought out. In this case, it is necessary to make appropriate adjustments according to the printer's user manual to ensure that the printer's tension is set correctly.

In addition, there are a few other factors that can cause the ribbon to be brought out, such as printing too fast, printing the label in the wrong material, etc. Therefore, when solving the problem of ribbon being brought out, these factors need to be considered, and corresponding measures should be taken to adjust and improve.

Extended content: In addition to the problem of ribbon being brought out when printing, we can further improve the print quality and reduce the amount of ribbon used. For example, properly adjusting your printer's printing parameters, selecting the right printing materials, and regularly cleaning and maintaining your printer are all ways to help improve your print results and extend the life of your ribbon.

In addition, understand the difference between different types of ribbons, such as resin ribbons and wax resin hybrid ribbons, and you can also choose the right ribbon according to your actual needs to achieve better printing results.

Zebra label printers may bring out ribbons when printing virtual takes, and there may be the following reasons:

1.Incorrect ribbon installation: If the ribbon is not properly installed under the printer's print head, it will cause the ribbon to be brought out during the printing process. At this point, you need to check that the ribbon is installed correctly to make sure it fits snugly with the print head.

2.Improper ribbon tension adjustment: Printers are often equipped with ribbon tension adjustment devices, which can cause the ribbon to be carried out if the tension is set too tightly or too loosely. In the process of use, the tension of the carbon cavity can be appropriately adjusted to ensure its stable operation during the printing process.

3.Incomplete printer cleaning: If there are impurities such as dust and paper scraps inside the printer, it may affect the normal operation of the ribbon and cause the ribbon to be carried out.

Regular cleaning of the printer, especially the printhead and ribbon path, can effectively prevent this problem.

In addition, you need to pay attention to the following extensions:

Quality and longevity of ribbons: Low-quality ribbons may be easier to take out, so choosing a high-quality ribbon can reduce the occurrence of such problems. In addition, timely replacement of aging ribbons can also ensure print quality and reduce the probability of ribbons being carried out.

Printer parameter settings: Some printers have parameter setting options, such as print speed, print density, etc., and different settings may have an impact on the use of ribbons. These parameters can be adjusted appropriately on a case-by-case basis to get the best printing results.

In conclusion, when the zebra label printer brings out the ribbon when printing, we should carefully check the installation and tension adjustment of the ribbon, and keep the printer clean. At the same time, choosing a high-quality ribbon and the right printer parameter settings are also effective ways to prevent this problem.

Zebra label printers can bring out ribbons when printing for several reasons:

1.Incorrect ribbon loading: If the ribbon is not properly loaded into the printer, it may be brought out or stuck, causing problems while printing. When installing the ribbon, make sure it passes through the printer's drivetrain correctly and is not loose or stuck.

2.Ribbon tension is not properly adjusted: Ribbon tension is an important factor affecting print quality and stability.

If the ribbon tension is too tight or too loose, it may be carried out or distorted, resulting in a drop in print quality. Make sure to make the correct ribbon tension adjustment according to the printer's instructions.

3.Poor ribbon quality: Low-quality ribbons can break or twist easily, causing ribbons to be carried out when printing. Choose a high-quality ribbon and follow the manufacturer's recommendations to choose the right ribbon for your printer model.

Also, there are some other possible reasons such as broken printer parts, wrong printer settings, or improper maintenance of the printer, etc. If none of the above methods solve the problem, it is recommended to contact the printer manufacturer or professional technician for further troubleshooting and repair.

Extended Content: In addition to the above reasons, it is also worth noting that operating errors during use can also cause ribbons to be taken out. For example, printing with too much force or operating the printer incorrectly can cause damage or carry-out effects on the ribbon.

Therefore, when using the printer, it is important to follow the correct operating steps and maintain the appropriate operating force to ensure that the spinning process goes smoothly. In addition, regular maintenance and cleaning of the printer is also an important measure to maintain the quality and stability of the print, which can avoid problems such as ribbons being carried out.

There are several reasons why zebra label printers are bringing out carbon dust digging bands while printing.

First of all, it may be that the ribbon is not installed correctly. When using zebra label printers, the ribbon needs to be properly seated between the print head and the paper. If the ribbon is not properly installed or loosened, it will be brought out during printing.

The solution to this problem is to reinstall the ribbon and make sure it is securely attached to the printhead.

Secondly, it may be that the ribbon is of poor quality. If the ribbon is of poor quality, or if it has been used many times and is wearing out, it is easy to bring the ribbon out when printing. It is recommended to replace the ribbon with a new one and choose the best ribbon brand to ensure the printing quality and stability.

Also, it may be that the printer's print head needs to be cleaned. If there are impurities such as dust, dirt, or toner on the print head, the ribbon will be brought out when printing. Clean the printhead regularly, you can use a special cleaning stick or cleaning paper to ensure the cleanliness and normal operation of the printhead.

Extended content: In addition to the reasons listed above, there are a few other factors that can cause ribbons to be carried out when printing on zebra label printers. For example, a printer that prints too fast or has uneven print tension can cause the ribbon to be carried out.

At this time, you can adjust the printer's print settings, reduce the printing speed or adjust the printing tension to solve the problem of the ribbon being brought out.

In short, when the zebra label printer brings out the ribbon when printing, we can check the ribbon installation, ribbon quality, printhead cleaning and print settings, and take corresponding measures to ensure the printing quality and stability.

The reasons why the zebra label printer brings out the ribbon when printing may be the following:

1.Incorrect ribbon installation: The ribbon on the printer may not have been installed correctly or installed poorly, resulting in it being brought out during the printing process. In this case, you can check and reinstall the ribbon to ensure that it is properly seated on the printhead.

2.Ribbon quality issues: Poor or aging ribbons can cause them to fall off easily during printing.

This may be due to the fact that the material of the ribbon is not suitable for the printer, or the ribbon has expired or has been used for too long. In this case, it is recommended to replace the ribbon with a new one and choose the ribbon that is suitable for the printer model.

3.Incorrect printer settings: The printer may be set up incorrectly, resulting in an uneven pressure between the printhead and the ribbon, making it easy for the ribbon to come out.

In this case, you can check the printer's settings, make sure there is close contact between the print head and the ribbon, and adjust the pressure settings of the printer.

It should be noted that different models of zebra label printers may have different ways of using ribbons and related settings, so when solving this problem, it is recommended to refer to the printer's operating manual or consult a professional for a more accurate solution.

In addition, in order to avoid the problem of ribbon carryover, you can also take some additional measures, such as cleaning the printer's print head regularly, keeping the environment around the printer clean, choosing the best ribbon, etc., to ensure the printing quality and stability.