Wallpaper has a fringing phenomenon, is there any way to remedy it?

Wallpaper warping is a lot of owners will encounter trouble, wallpaper warping is caused by many reasons, especially pay attention to the decoration construction, the following summary of a few precautions, I hope to solve your troubles!

Clause.

First, pay attention to the firmness of the wall

When sticking wallpaper on the wall decoration, you must communicate with the painter in advance, so that the master can add more 901 glue, so that the putty on the wall is harder and firmer, not easy to fall off, and it is not easy to warp in the later stage!

Clause.

2. Reduce glue extrusion at the seams

If the surface of the wallpaper itself is long fiber, or embroidery, etc., this is relatively thick, the edge of the later stage must be easier to warp, thick must be heavy, and the surface of long fiber or embroidery, there is also a certain tension, it is easy to warp, pay attention to the splicing, let the master try to scrape a little. Then reduce the glue squeezing, so that the glue at the seam is also slightly more, don't scrape it all away. In this way, it is easy to warp the edge after air drying in the later stage.

Clause.

Third, the surface process of wallpaper attributes

Different wallpaper attributes, different surface processes, when the master dispenses glue, look at the master's experience, to target different wallpapers. When playing glutinous rice glue, add more water and add less thick and thin, it all depends on the experience of the master, after all, the wallpaper is pasted one by one, there are seams, the seams are naturally scraped more, glutinous rice glue is naturally thinner than the middle, plus more contact with the space, it must be easy to open the glue, different materials of wallpaper, the glutinous rice glue is thin or thick!

Clause.

Fourth, pay attention to the dampness of the house wall

There is also an important reason for the mildew on the warped side, the owner's house is the east side of the household. That is, the wall next to the table is pasted with wallpaper or wall cloth, and the time is exposed to the wind and sun. The walls will also slowly seep water.

It's not that there is a large area of water leakage, but it is slowly penetrating, and after ten or eight years, the wall must be more than the middle of the family. The walls are going to be damp, and he may be later. The wall putty powder will be loose, and the weathering may also cause the wallpaper to be a little warped.

This wall cloth can not be avoided, and there will be hollowing in the middle after a long time, for example, the glutinous rice glue will be dry for a long time, and the glutinous rice glue will naturally fall off with the wall and appear hollow.

Clause.

Fifth, the wallpaper should be edge-banded

After the wallpaper is pasted, it is generally necessary to do edge banding, and the edge banding is to prevent the wallpaper from warping. Generally, after two or three years of use of wallpaper, air and moisture will erode the wallpaper for a long time, and it is difficult to avoid problems such as warping and mildew in this environment, so it is necessary to do wallpaper edge banding.

Some owners are more mindful of warping, so don't choose wallpaper with embroidery, silk long fiber, and other complex processes on the surface, and choose wallpaper that is not too thick. Thick wallpaper is also easy to warp, because it is thick and heavy, and it will have a pull on the wall. It is easy to warp in the later stage.

It is recommended to choose a plain and thinner wallpaper, which will be more firm and not easy to warp!

If a large area of wallpaper warping occurs, it should be torn off and re-pasted with a sticky adhesive. If there are a lot of air bubbles, you can use a needle to prick the eye to exhaust, if the edge is upturned, it may be that the window is not clean, you can wipe it clean and then water it to fix.

If the wallpaper has a raised edge, re-glue the wallpaper with the glue used for wallpaper to give it a new look. When pasting, pay attention to cleaning up the floating ash on the wallpaper and the wall, which is easier to stick.

If the wallpaper appears to be edged, you can buy a special glue for wallpaper, apply some glue on the wallpaper, and then glue the wallpaper tightly, which can solve this problem.

If the wallpaper appears to be edged, remove the original glue and putty layer of the wall, scrape some putty powder again, re-glue, and hang flat with a plastic scraper.

Decoration has always been a big thing, because it not only has a large amount of work, a long time, but also a lot of money, and the most important thing is to invest a lot of energy, in order to get up every morning when you see your satisfaction with the decoration will be happy, then the day's work and study will be efficient, but also want to let every day come back from work, you are tired, you can see a good decoration to relax.

If the economic conditions allow, then try how to be luxurious, choose your favorite style, but if you don't have money, especially young people who are working hard outside, renting a house is also a lot of expense, so choose to paste wallpaper, there are various colors, various patterns to choose from. But after a period of time, I found that the wallpaper appeared warped, which may be because I was not serious enough in the construction at that time, or it may be that the quality of the wallpaper is too poor, or it is damp, and it is often rubbed, etc.

If the wallpaper appears to be warped, there are a few things you can do:

1. Clean up and smooth the place on the edge of the wallpaper, including the wall and wallpaper, and then glue them together with special glue to minimize impurities.

2. Cut off the upturned part and paste it with the same wallpaper. This is more convenient, but the problem is that if the wallpaper pattern is more complicated, cut and pasted differently, then the new wallpaper and the old wallpaper can not form a whole well, then it will look very ugly.

3. Tear off all the wallpaper of the wall and paste the new wallpaper. This can not only dispose of the warped wallpaper, but also paste a new one, so it feels more comfortable, but the problem is that it costs more money and is very troublesome.

4. Just let it be cocked. Because sometimes the reason why the wallpaper is warped is because the humidity there is heavier, for example, the wallpaper next to the bathroom is easy to mold and warped, so if you paste a new wallpaper, it will also appear again, so it is better to put it naturally and ignore it.

Immediately glue the pry edge to the place, if not treated, the warping will be very serious, and it will affect the degree of compliance in other places.

You can choose to use tape or glue to glue all the corners to it firmly, and you can get it.

If there is a warped edge, you should re-paste the wallpaper and paste it back again, so that you can do it.

Wallpaper is a relatively common material in home decoration, but there may be warping and cracking after wallpaper. Next, PCHOUSE will introduce you to what problems will cause warping and cracking of wallpaper.

1. Improper construction.

1) Uneven shrinkage and local cracking caused by sunlight and strong wind blowing.

2) The softening time is too long, the expansion is too long, and shrinkage joints are formed after drying.

3) The glue concentration is too low, the viscosity is insufficient, and the wallpaper cannot be adhered to.

4) Excessive local glue and uneven shrinkage.

5) Excessive force on the scraper when pasting, or too much stretching and widening of the wallpaper during construction, resulting in excessive stretching and shrinkage joints after drying.

6) When double-layer cutting, the knife edge is repeated, and the seam is revealed.

7) The operator is not strict with the seam.

2. Improper products.

Including improper selection of products and improper blending of products. Before construction, you should first evaluate the wallpaper that will be constructed, and it is best to do a tentative paste test in advance, choose the right adhesive product, and not rely on experience alone. If the heavy wallpaper is pasted with wallpaper powder with average performance, there is no packaging instructions when the product is deployed, the wallpaper glue powder is too short to open the glue, the stirring is uneven, and it cannot be completely gelatinized; Improper glue opening method causes clumping and low viscosity of glue.

3. Environmental factors.

including the temperature and humidity conditions of the construction; the firmness of the base layer (putty) of the wall; the finish and water absorption of the wall, the sealing effect of the wall; The bearing capacity of the construction surface, etc., in this case, blind construction will inevitably cause problems.

It is recommended that the construction be inspected on-site and repaired. If you want to fix it yourself:

For the warped edge, use a syringe to suck a little glue in. If the glue is too viscous at this time and it is not easy to suck into the syringe, you can pour it into it from the tail of the syringe and then put it into the pusher.

2. You can clean up the wall of the flying wallpaper a little, and then inject glue into the wall on the back of the wallpaper.

3. If it is a pure paper wallpaper, the glue is not too viscous, if it is PVC, especially the deep embossed wallpaper, you can mix the glue a little thicker. Generally, squeeze glue into it, don't fill all the walls, get about two-thirds, and then use a small scraper.

4. Carefully squeeze out the excess glue, you can add a little bit of strength to make the flying wallpaper re-paste. This repair method is mainly for the wallpaper of more ordinary materials, if it is gravel or flocking and other wallpaper, because of the particularity of the wallpaper, it is best not to stain the surface with glue, and it is best not to use a scraper to scrape, to use a special brush to deal with.

5.If the wallpaper is damaged, it needs to be repaired by a special construction personnel, and it is recommended to contact the construction personnel.

Generally, the service life of wallpaper is no problem in 5-10 years, but it is inevitable to warp after a long time, so the maintenance and maintenance of wallpaper is the key.

1. The room where the wallpaper has just been laid should be closed doors and windows, and it is strictly forbidden for the wind to blow, and the wallpaper must be in a dry state.

2. When pasting and pasting the last three. For four days, you can use a slightly damp flat towel or the sea surface to wipe off the residual glue left on the seams of the wallpaper.

3. After all, the wallpaper is paper, which can be wiped but not resistant to knocking, if it is found that there is a slight or small damage, it can be covered with pigments or paints of similar colors.

4. Flat printing (non-concave-convex) wallpaper, when cleaning on weekdays, you can use a feather duster to wipe off the surface dust, and concave and convex wallpaper, every 3 or 6 months, you can use a vacuum cleaner or soft brush to wipe off the surface dust.

5. After pasting the wallpaper, after two or three years, attention should be paid to the seams and turns, and if it is found that there are warping edges and cracks, it should be immediately glued to prolong the service life of the wallpaper.

6. Pay attention to the wallpaper pasted to prevent hard objects or sharp things from scratching, after a certain period of time, the seams in some places are cracked, and they should be subsidized in time, and they cannot be allowed to develop.

7. When the wallpaper in the bathroom is hung with water droplets and water vapor on the wall, the window and exhaust fan should be opened in time, or the water droplets should be wiped clean with a dry towel first, because for a long time, the quality of the wallpaper will be damaged, and white spots or blisters will appear.

8. In a room that is too dry, open the window in time to avoid direct sunlight for too long, otherwise it will have a greater negative impact on the dark wallpaper color.

9. If you accidentally stain the wallpaper, just wipe it with water or detergent dipped in the sea, and you can get rid of the stain.

First, the treatment of wallpaper warping.

Wallpaper warping is generally due to the change of weather temperature and humidity caused by the phenomenon of thermal expansion and contraction, generally only need to use professional wallpaper glue to paste, and use a flat object, such as a book, to press it.

Second, the treatment of wallpaper blistering.

If the wallpaper in the home has a blistering phenomenon, it is generally caused by uneven gluing and blistering due to lack of glue when the wall is partially pasted. You can use a sewing needle to make a small hole in the blistering position on the surface of the wallpaper, release the gas, take an appropriate amount of adhesive and put it into the needle hole to stick tightly, and finally flatten it with a flat book to dry.

Third, the treatment of moldy wallpaper.

Due to excessive moisture in the indoor air and poor indoor ventilation, mold will grow on the wallpaper. To deal with wallpaper mildew, you can first wipe the wall with a dry cloth, and then mix half a bottle cap of 84 disinfectant solution into 4 paper cups of water, mix it evenly, and use it to wipe the wall with mildew.

Fourth, the treatment of damaged wallpaper.

Broken wallpaper is usually caused by scratches from hard objects or accidental bumps when moving. At this time, the damage in a small area can be repaired with glue; If the area is large, it is generally recommended to re-pavement.

Fifth, the treatment of yellowing of wallpaper.

There are generally three ways to deal with yellowing of wallpaper:

1. If the wall ash has not dried thoroughly when moving in, the wallpaper will be pasted, resulting in a chemical reaction between the alkaline substances in the wall ash and the bottom of the wallpaper, making the surface yellow. This phenomenon is difficult to deal with, and the wall needs to be removed and reconstructed. 2. If there is yellowing after living for a few years, most of it is caused by the aging of the paper due to sunlight and air contact, at this time, you can use "safety bleach" dipped in the towel to wipe it, and then wipe it with water after half an hour.

You can first do a small piece of the wall in the hidden place for experimentation, observe the effect, if the effect is ideal, you can use it for the whole wall treatment. 3. If some of the wallpaper turns yellow due to smoke, it is advisable to wipe it with diluted caustic soda solution.

end precautions.

1. When the resident is not at home, he should use curtains or blinds to avoid direct sunlight. At the same time, be careful not to let the hot air from air conditioners and other equipment blow directly on the wallpaper when it is cool. Because the wallpaper may also be deformed and discolored when exposed to heat.

In summer, wallpaper usually appears to open glue, warp, and partially fall off the wall, which is mainly caused by indoor temperature, humidity, and other decorative objects.

2. Daily smoke or kitchen fumes will make the wallpaper yellow in a short time; Condensation or moisture are the main causes of stains, peeling and mildew, so in order to avoid these two situations, it is necessary to pay attention to maintaining indoor ventilation and humidity regulation.

3. Pay attention to daily cleaning, all wallpaper walls should be vacuumed regularly, vacuum cleaners or feather dusters can remove dust, do not directly scrub the wallpaper with water. If there is a dirt that is difficult to scrub, such as oil stains, you can wipe them with an eraser or wring them out with a towel dipped in some cleaning solution and gently wipe the stains.