What is the method of starting the needle with a flat needle?

1, Step 1, prepare the yarn and the yarn needle, and put the yarn on the yarn needle.

2. When catching the needle with the right hand, the short yarn is also caught, the ring finger and the little finger of the left hand are close to the palm, and the middle finger, index finger and thumb are close together to wrap a circle of wool from the outside to the inside.

3. The sweater needle passes from the back of the hand through the wool between the index finger and the thumb.

4. Release the left hand and straighten the wool on the side of the long side into the following pattern.

5. Depending on the size of the wool and the desired width of the scarf, the number of stitches is different.

6. Hold the needle in the left hand and pass the needle in the right hand through the middle from above.

7. Wrap the thread from the bottom to the top and lift the thread inward.

8. Put down the needle that has been lifted, weave a flat needle, and repeat it all the time.

Finger hanging thread stitching method: The rod needle used in this section of the needle is two needles larger than the actual needle number used in the work.

Crochet needle, rod needle natural color line wiring needle method: natural color line is directly from the wool needle, wiring is first through a wiring (nylon composition is the best) to start the needle and then knit with wool, wiring needle method for the need to splice the fabric, so that the joint is more beautiful.

Ring needle use: After the required needle is lifted, the first needle is connected into a cylinder and knitted all the way forward.

Knitting scarf needle skills.

It should be noted that for many users, the double ingot needle is not a particularly complicated yarn weaving method, because at the beginning, the needle was not done correctly.

It should be noted that under normal circumstances, the number of needles of the double ingots needle is the number of even needles, so it is also necessary to knit the number of even needles when steaming, not singular, and at the same time, in order to be able to weave well, you also need to relax the wool as much as possible when starting the needle, but it is not too loose, it is appropriate, you can pull it, so that the wool knot woven behind will make the tightness even.

The above content refers to Encyclopedia - Scarf Knitting - Rods and Needles Basics.

1.The first step is to start the needle, here you can take any number of needles, and you can look at it according to the width you need when you knit the scarf.

2.In the left hand, the knitting needle is raised, and in the right hand, the knitting needle is not yet threaded. It's a habit of right-handers.

3.Poke the needle into the first yarn coil from the inside out, pay attention to the stitching method, the needle in the right hand is under the needle in the left hand, and poke it from the inside out.

4.At this time, hold the thread in your right hand and wrap the thread from the outside to the inside, as shown in the figure below, noting that the needle in your right hand is still under the needle in your left hand.

5.Gently pull out the thread, be careful not to take away the thread that you just went around, and if you are not used to it, you can press the thread you just wound with the help of your fingers. Once completed, it will be shown in the image below.

1. Prepare the yarn and knitting needle.

2. Wrap the wool around and put one end on it.

3. Then go down and out of the circle. Make a looper.

4. Thread the needle out of the sleeve.

5. Then wrap the coil on the needle with the right finger, and tighten the coil appropriately, so that a needle is raised.

6. Then continue to repeat the operation to achieve the required number of stitches. This completes the needle lifting.

7. Repeat the above steps in turn.

8. In this way, the flat needle is done.

1.Start by crocheting a crochet hook with an appropriate number of braids. For example, if I think of 150 pairs, I hook 150 braids.

2.Knit 150 stitches on the protrusion on the reverse side of the braid. (Pick a little looser.) ）3.Circle knitting under the needle 3 rows.

4.Pick and dig the needle, that's the key. The original rod needle is knitted under the needle, and after the knitting of 1 needle, it is at the root of the corresponding needle to pick up the rent and let 1 needle. After weaving 150 stitches, you will finish picking 150 stitches. It became 150 pairs.

5.Pull off the hollow line.

How to choose the right yarn needle? The best size needle to use for knitting a scarf, and the size of the needle depends on how thick the thread you use. It also depends on the quality of the wool, if there is fluff on the thick line, it is best to use a stick needle, thinner than chopsticks.

If there is no fluff, use an 8-gauge needle. If it is a fine thread with fluff, you should also use a gauge needle, and if it is not fluffy, you can use a 10-gauge needle.

The method of collecting the flat needle is to finish with the flat needle first, pick a needle through the first needle, knit a flat needle in the second needle, and then press a needle to complete it. The details are as follows:

1. First of all, finish with a flat needle, start with the first needle to pick a needle, the second knitting a needle to a flat needle, and then press the picked needle forward with a needle.

2. Then, knit another flat needle, use the back pressure needle to press forward another needle, so that you can knit a needle forward, and press off a needle later.

3. In this way, press the needle forward until the last needle, cut the wool short, and then thread the wool in the last needle and tighten it.

4. In this way, the end of the ordinary flat needle is the same as the beginning of the needle, and it is also convenient to tie the wool spike, and it is also very good to tie a wool spike every 3 or 5 needles.