The tractor hydraulic pressure is getting slower and slower and slower in the end, what is the reaso

The hydraulic pressure of the tractor is getting slower and slower, and finally it is not riding, it may be caused by insufficient pressure, and it is best to drive to the maintenance place to do a thorough inspection.

The hydraulic starter of the tractor was caused by his lack of pressure. But there is no hydraulic fluid. Or it is caused by poor sealing.

**] This article analyzes the most common slow lifting faults of tractor hydraulic suspension system to remind users to pay attention when using it. 1 Reason The reason for the slow lifting of suspended farm tools is mainly due to the reduction of the amount of oil entering the cylinder, the slow establishment of oil pressure, and the oil supply.

This may be a problem with the tractor's hydraulic pump or hydraulic oil, right? It's best to take the car to the repair shop and have someone else inspect it.

If the tractor hydraulics get slower and slower, if you can't afford this in the end, it may be that there is a problem with the nutrition inside.

The tractor's hydraulic lift is getting slower and slower, probably due to insufficient fluid buildup.

The tractor hydraulics are getting slower and slower, and finally what is the reason for not washing the suffix of the confusion which is normal This tractor hydraulics are getting slower and slower, and finally there is no need for this reason, and it will start again after being confused. It's normal again.

There is a problem with the hydraulic press. It should be changed.

56] Wei Wei, Ye Qingmei, Analysis of Commercial Bank Profitability Based on Improved DuPont Analysis: A Case Study of Industrial and Commercial Bank of China [J].Business Accounting, 2017(7):46-49

If you start it now, it's not normal again, and I personally think there's a reason for this.

The tractor hydraulic is getting slower and slower the more you ride, and in the end it can't get up, what is the reason for starting it again after extinguishing the fire, I think this may be the problem that the starter is broken.

Is tractor hydraulics getting more and more up? In the end, what is the reason for not being able to do anything, it can only be some engine oil or something. Well, the reason.

Summary. Hello, dear, I'll answer this question for you<>

The tractor is not hydraulic, what is going on 1, the agricultural machinery is too heavy, does not match the tractor or the connection hole between the pull-down rod and the lifting rod is improperly used: replace the lighter agricultural machinery. 2. The blockage of the hydraulic oil filter causes the lifting to be weak and not lifted

Unclog the oil filter. 3. The lifting hydraulic oil of the tractor is insufficient, and there is oil leakage in the oil circuit: add lifting hydraulic oil.

4. The hydraulic oil model of the tractor is not suitable. 5. Air intake into the hydraulic pipeline. 6. The pressure of the distributor or the safety valve of the multi-way valve is low.

Tractors are hydraulic, and nothing is going on.

Hello, dear, this question is answered by me for you <>

The tractor is not hydraulic, what is going on1, the agricultural machinery is too heavy, does not match the tractor or the connection hole between the pull-down rod and the lifting rod is not used properly: replace the lighter agricultural machinery. 2. The blockage of the hydraulic oil filter causes the lifting to be weak and not lifted

Unclog the oil filter. 3. The lifting hydraulic oil of the tractor is insufficient, and there is oil leakage in the oil circuit: add the lifting liquid family rolling oil.

4. The hydraulic oil model of the tractor is not suitable. 5. Air intake into the hydraulic pipeline. 6. The pressure of the distributor or the safety valve of the multi-way valve is low.

This situation is generally that the key of the hydraulic pump and the gearbox power take-off connecting shaft is twisted and broken, and there will be a time when the unloaded can be slowly raised, and it is not good to eat heavy. Another situation is to eat heavy and start from the state, but slowly, increase the throttle has not improved significantly, it is necessary to check the oil hose to see if there is a discount, focusing on checking the bottom pressure oil inlet part, to see if it is blocked, the oil supply is insufficient. If the light load lifting is normal, the heavy load is difficult to lift, and sometimes the throttle is increased to barely lift, you should consider replacing the oil size pants pump.

Summary. Dear, glad to answer for you! It is not easy to start after the tractor is turned off; There are several reasons why the tractor is not easy to start after it is turned off:

1.Insufficient fuel or clogged fuel filter, resulting in insufficient fuel supply; 2.The air filter is clogged, resulting in insufficient air ingress; 3.

Faulty ignition system, such as dirty or damaged spark plugs; 4.Low battery or poor circuit connection, causing the starting system to not work properly; 5.The engine is overheated or the water temperature is too low to start; 6.

Poor fuel quality leads to incomplete combustion and affects engine starting.

Dear, very round do happy to answer for you! It is not easy to start after the tractor is turned off; It is not easy to start after the tractor is turned off, and there are several reasons: 1

Insufficient fuel or clogged fuel filter, resulting in insufficient fuel supply; 2.The air filter is clogged, resulting in insufficient air ingress; 3.Ignition system failure, such as dirty spark plugs or damage to Xunyuan; 4.

Low battery or poor circuit connection, causing the starting system to not work properly; 5.The engine is too hot or the water temperature is too low, resulting in the inability to start; 6.Poor fuel quality leads to incomplete combustion and affects engine starting.

Check that the air filter is clean and if there is dirt that needs to be cleaned or replaced; 3.Check whether the spark plug is normal, and replace it in time if there is a problem; 4.Check whether the battery level and circuit connection are good, and repair it in time if there is any problem; 5.

Check whether the water temperature of the engine is normal, and if there is a problem, it needs to be solved in time; 6.Choose the fuel that meets the requirements to ensure the combustion efficiency.

There can be several reasons why a tractor is difficult to start. First of all, problems with the fuel supply can lead to start-up difficulties. It may be that the fuel oil circuit is blocked, the fuel filter needs to be replaced or cleaned, or the wheel huai or the Ranling Tongge material pump is faulty.

Second, electrical system failures can be one of the problems, such as low battery, damaged starter motor, or poor contact. In addition, faults in the ignition system can also cause difficulties in starting, such as aging spark plugs, faulty ignition coils, or ignition switch problems. In addition, problems with mechanical components, such as a lack of lubricating oil in the engine, insufficient cylinder compression, or damaged starter gears, can also cause start-up difficulties.

Pro, one is that the cylinder head nut is not tightened or the cylinder gasket is damaged When turning the crankshaft, if you find that there is an air leakage sound at the joint surface of the cylinder head and the body, it may be that the cylinder head nut is not tightened, or it may be that the cylinder gasket is damaged. If it is the former, it should be tightened as required. If it is the latter, when the damage to the cylinder gasket is not serious, the damage can be repaired with asbestos thread, and the new gasket can be replaced when it is serious.

The second is the intake and exhaust valve leakage There are two reasons for this kind of air leakage: one is that the valve clearance is too small, so that the valve is not closed tightly, and the valve clearance needs to be readjusted. The other is that there may be spots on the valve sealing cone, such as rust, charcoal and other debris, which also makes the valve not close tightly.

When you check the crankshaft, you can shake it, if you hear a "squeak, squeak" sound in the air filter and exhaust pipe, it means that there is a leak in the intake and exhaust valves. The valves need to be ground. The third is excessive wear of the piston ring When the crankshaft is rotated, there is an air leakage sound inside the body (such as the oil low shell), and most of the reasons are on the piston ring.

You can add some clean oil to the cylinder, if the compression force is significantly increased after adding, then the piston ring should be replaced. Piston ring counterparting The piston ring openings are moved to a straight line (commonly known as counterpart), or the piston rings are stuck in the ring groove due to carbon deposits, and the compression cylinder cannot be ejected. The phenomenon is that when the crankshaft is rotated, there is an air leakage sound in the crankcase.

The piston ring should be removed to remove the deposit. If the ring mouth is moved to a straight line, the positions of the openings should be evenly distributed, but the piston pin direction must be avoided. Injector fixing bolts are loose and there is an air leak at the injector lump on the cylinder head, rent or tighten it.

Hello <>

If the tractor's electro-hydraulic lifting function suddenly has no pressure, there may be several reasons:1Insufficient hydraulic fluid.

Hydraulic oil is a key part of electronically controlled hydraulic lifting, if the hydraulic oil is insufficient, it will cause the hydraulic system to not work properly and cannot lift the goods. You need to check if the oil level of the hydraulic oil is below the minimum mark, and if so, then add the hydraulic oil in time. 2.

Hydraulic pump failure. The hydraulic pump is the core component of the hydraulic system, and if the hydraulic pump fails, it will cause the hydraulic system to not work properly. You can judge whether the hydraulic pump is faulty by checking the noise of the hydraulic stove pump, hydraulic oil pressure and other indicators.

3.Hydraulic valve failure. The hydraulic valve is an important part that controls the work of the hydraulic system, and if the hydraulic valve fails, it will cause the hydraulic system to fail to work properly.

You can tell if the hydraulic valve is faulty by checking whether the action of the hydraulic valve is sensitive, whether there are problems such as stagnation. 4.Blocked hydraulic lines.

If the tractor's motor-controlled hydraulic lift suddenly loses pressure, it may be due to a blockage in the hydraulic line. You need to check the hydraulic lines for foreign objects, sediments, and other conditions that affect the flow of hydraulics. If you are unable to diagnose the problem yourself, it is recommended that you have a professional technician inspect and repair it.

At the same time, in order to maintain the normal operation of the tractor's electric control hydraulic lifting function, please regularly check whether the various components of the hydraulic system are operating normally, and replace the hydraulic oil and other maintenance work in time.

I don't want to get up with my high horsepower, and it's slow.

Hello, dear, I'm glad I can answer for you. The reasons why the tractor cannot be hydraulically unhydrated are as follows: 1The agricultural machinery is too heavy, does not match the tractor, or the connection hole between the pull-down rod and the lifting rod is not used properly

Replace lighter agricultural implements. 2.The blockage of the hydraulic oil filter shed dispenser causes the lifting to be weak and not lifted

Unclog the oil filter. 3.The lifting hydraulic fluid of the drag key pull machine is insufficient, and the oil circuit has oil leakage

Add lifting hydraulic fluid. 4.The type of hydraulic oil for the tractor is not suitable.

5.Air intake for hydraulic lines. 6.

Caused by low pressure in the distributor or multi-way valve safety valve.

The heavy bucket can get up a section of the cylinder, how to adjust.

Kiss, adjust the throttle valve to control the speed of the hydraulic cylinder.