The dipped beam indicator of the dashboard of modern cars is not lit, but the low beam is on

If the instrument indicator is not lit, first check the power supply fuse of the dashboard, and replace it if it is blown. Disassemble the dashboard, the lights are generally at the back of the dashboard, replace the lights that are not lit, and generally the individual lights are not lit to indicate that there is no problem with the fuse and wire, the main reasons are as follows

1. The lamp of the dashboard is damaged and needs to be replaced in time;

2. If the power supply line of the dashboard is broken, there is an open circuit or short circuit, which will also cause the car dashboard to not light up;

3. If the power supply fuse of the car dashboard is broken, there will naturally be no power supply, and the dashboard will not light up.

Precautions in the use of the car dashboard:

1. When the indicator light is on, the odometer should be observed immediately, if the cumulative mileage reaches or exceeds l00,000km, the timing toothed belt must be replaced, otherwise the timing toothed belt may break, so that the engine can not work normally.

2. After replacing the new timing toothed belt, it is necessary to open the rubber plug outside the reset switch on the mileage dial, and press the reset switch inside with a small round bar to extinguish the indicator light of the timing toothed belt.

3. After replacing the new timing toothed belt, remove the odometer and adjust all the readings on the odometer to the 0 position.

Hello, the meter will show the high beam, which proves that you have turned on the high beam. If the bulb does not light up, it is necessary to check whether the fuse is broken and whether the bulb is broken.

Hello, the bulb inside the meter is broken [There is a problem with the car, ask the car master. 4S shop professional technician, 10 minutes to solve. 】

Check whether the lamp port assembly is broken, causing the low beam light to not light up. The headlight assembly needs to be replaced. Generally speaking, the fifth situation does not occur often, and the cost of other conditions is relatively not very high, but it is important to go to the repair station to investigate first, and then decide what way to repair after determining the problem.

Reasons why the low beam does not light up:

1. The battery is dead. You can press the horn at this time to keep the battery power, if you forget to turn off the electrical appliances and don't work overnight, the next morning then you won't be able to drive, and even the low beam can't be turned on;

2. Damage to the bulb. Most bulbs also have a certain life cycle, when the light intensity is not up to standard when it is close to scrapping, and at the same time, the heat is severe until the filament is burned. In addition, there are some reasons, such as the headlight assembly is easy to enter the water after the vehicle wades, and the temperature drops sharply after the heated bulb hits the water droplets, so there will be rupture and damage, which will affect the lack of light;

3. The fuse is blown out, most of the low beam fuses can be found in the engine compartment fuse box or the fuse box on the left side of the dashboard, and the fuse is indicated that behind the fuse box cover, use a special clip to take out the detection;

4. There is a fault problem in the low beam adjustment circuit. It may be that there is a problem with the light adjustment switch, and in such a situation, you can go to the store to carry out maintenance and measure whether the light switch adjustment logic is abnormal.

The main reasons why the car dashboard light does not light up are as follows: 1. The dashboard light is damaged; 2. The power supply wire of the dashboard is disconnected; 3. The power supply fuse of the dashboard is blown out; The problem can be solved by mainly examining the above aspects. First of all, check the power supply fuse of the dashboard, if it is blown can be replaced; Disassemble the instrument panel, the lights are generally at the back of the dashboard, and replace the lights that are not on.

Generally, if the individual lights do not turn on, it means that there is no problem with the fuse and wire.

Check if the vehicle's battery is charged, and then look at the fuse.

Summary. 1. The dashboard lighting is damaged; 2. The power supply wire of the dashboard is disconnected;

1. The dashboard lighting is damaged; 2. The power supply wire of the dashboard is disconnected;

3. The power supply fuse of the dashboard is blown out; First of all, check the power supply fuse of the dashboard, if it is blown can be replaced; Disassemble the dashboard, the lights are generally at the back of the dashboard, and replace the dry lights that are not lit. Generally, if the individual lights are not on, it means that the fuse and wire are not raised, and there is a problem.

The low beam is not on, nor is the low beam logo on the dashboard.

After turning on the low beam, there will be no sign on the car dashboard, and only when the high beam is turned on, there will be a sign that the high beam is turned on on the car dashboard.

The low beam does not light up when it is turned on, and there is no low beam directly.

1. Staring envy may be that the fuse inside the car's low beam is blowing, resulting in the car's low beam not lighting, and a new fuse needs to be replaced, and at the same time, the cause of the fuse blowing should be eliminated to avoid the installation of a new fuse and blowing. 2. It may be that the battery of the car is insufficient or out of power, and the lights will not light up if there is not enough power. 3. It may be that the control switch of the car light is faulty, resulting in the low beam can not be turned on, at this time, not only the low beam can not be turned on, but also the high beam of the car can not be turned on, and the new control switch needs to be replaced in time.

Most cars don't show up on the dashboard when they turn on their low beams. However, when the low beam is turned on, the background light on the dashboard will generally dim, and when the low beam is off, the brightness of the background light on the instrument panel will increase.

The light control area of most cars is on the left side of the main driver's steering wheel, and the light control buttons of most Xindan cars are knob-type.

When the low beam is turned on, there is no logo on the dashboard. When the high beam is turned on, there will be a sign that the high beam is on.

As a result, many riders often forget to turn off their low beams when using their bikes.

Some cars will be equipped with automatic headlights. This car has an automatic switch on the headlight control knob. Once you go to Auto, the headlights will be controlled automatically.

The automatic headlights do not turn on during the day, and the automatic headlights turn on automatically at night.

When you turn off the engine and get out of the car, the automatic headlights will automatically turn off.

So if the car has an automatic headlight function, you can use this function, which is still very easy to use.

When driving in the city, do not turn on the high beams, which will affect the vision of the driver of the oncoming car and the driver of the car in front.

When driving on a highway or country road without street lights, you can turn on your high beams. When encountering a car, you should turn off your high beams out of politeness.

When you are driving, if the limb with low beam indicator is not on, it will cause you a lot of trouble. Without indicators, you won't know if the low beams are on, which will affect your driving safety. So, what is the reason why the car low beam indicator does not light up?

First of all, the most common cause is a damaged light bulb. If the dipped beam bulb is broken, the indicator light will not come on. At this point, you need to replace the bulb. Also, the lifespan of low beam bulbs is limited, and if you are constantly driving on dim roads, the life of the bulb will be shorter.

Second, the circuitry of the indicator may be faulty. If there is a problem with the circuit, the indicator light will not light up. At this point, you need to inspect the circuit, find the problem, and fix it.

There is also the possibility that the battery voltage is insufficient. If the battery voltage is insufficient, there may be problems with the vehicle's electrical system. At this point, you will need to replace the battery or charge it to ensure that the vehicle's electrical system is working properly.

In short, when the low beam indicator is undefeated, you need to check whether the bulb is damaged first, and if there is no problem with the bulb, you need to check the circuit and battery voltage. If you don't know how to check or fix these problems, your best bet is to find a professional car mechanic to deal with them. Only by making sure that the vehicle's electrical system is working properly can you safely drive on the dark road.

The car does not have a low beam indicator, only turn on the high beam and high beam blue indicator will light up, I hope mine can help you. [If you have a problem with the car, ask the car master.] 4S shop professional technician, 10 minutes to solve. 】