Are the 2017 Geely Vision High Beams and Low Beams up and down in one place?

Updated on Car 2024-08-01
10 answers
  1. Anonymous users2024-02-15

    Geely Vision is not a place to adjust the high beam and low beam, there is a fluctuation button to adjust the low beam on the left side of the main driver in the car, and there is a position to adjust the height of the headlights in the hood headlights.

  2. Anonymous users2024-02-14

    Adjusted via a knob on the rear of the headlight assembly, you can adjust the light yourself with tools. Lift the engine cover, find the adjustment knob behind the headlight assembly, and judge whether the knob is adjusted left and right or up and down when adjusting. Park the car directly opposite the wall about 10 meters away and adjust it, if you feel troublesome, you can go to the repair shop to adjust.

  3. Anonymous users2024-02-13

    There is a way to adjust the light at the bottom of the steering wheel.

  4. Anonymous users2024-02-12

    Not in one place, you can look at the manual, which has high beams marked on it, because the low beam signs are different.

    Low beam. Popular Science China |This entry is reviewed by the "Science Popularization China" Science Encyclopedia Entry Compilation and Application Work Project.

    The low beam is for close lighting, and the design requirements are to have a large irradiation range (160°), a short irradiation distance, and the light gathering cannot be adjusted.

    Chinese name. Low beam.

    Foreign name. low beam

    Irradiation distance. It is about 30-40 meters or so.

    Peculiarity. The irradiation range is large and the irradiation distance is short. Category. Lamp.

    Fast. Navigation.

    Related information. Brief introduction.

    Definition. The irradiation distance of the low beam is about 30-40 meters. According to experiments, it is known:

    When driving at a speed of 55 km/h at night, the brakes were immediately applied when the situation was noticed, and the stopping distance was exactly 30 meters. That is, when the situation is found within the range of low beam illumination, it stops immediately, and there is no gap between the car and the object. Of course, this is when the vehicle condition, road conditions and the driver's response are good, if the speed is higher than this, the vehicle condition, road conditions are poor and the driver's fatigue reaction time is long, the result can be imagined.

    Therefore, it is important to control the speed of the vehicle when driving at night. When using high beams on a flat, wide, well-sighted road, the speed of the vehicle can be appropriately accelerated; And when the car encounters uneven road surface or turning or bridges or narrow roads or intersections and other complex situations, it should slow down and slow down, and the speed is generally controlled within 40 kilometers per hour.

    In the following cases, the low beam must be turned on; Turn on your low beams when driving in dark areas where there are no street lights and when it is dark in the evening or when dawn is at dawn. If you are caught up in fog, snow or heavy rain and your vision is clouded, then you must turn on your low beams even during the day; In some sections, although there is lighting, but the brightness is not enough, you should also turn on the low beams.

  5. Anonymous users2024-02-11

    Operation method of Geely Vision High Beam and Low Beam:

    1. Press the brake pedal of the car until you can't press it to prepare for starting the engine.

    2. Press the one-button start button to start the car's engine system.

    3. The instrument light is lit up, and the whole vehicle system is energized.

    Fourth, twist the headlight switch and light up the headlights of the silver car.

    5. Twist the switch of low beam and high beam, twist the switch forward, and the high beam light will light up; After turning the switch to the bucket, the low beam lights up to read the feast.

  6. Anonymous users2024-02-10

    1. Pull the wrench in the engine compartment to unlock the engine compartment lock.

    2. After that, pull the wrench in front of the engine compartment to lift the engine compartment cover.

    3. After that, you can use the bracket to support the engine compartment cover.

    4. After that, you can find the headlight adjustment knob below the illustrated position in the engine compartment.

    5. After that, you can adjust the light knob by using the change cone, adjust it upward, and the angle of the high beam will become higher, and adjust it downward, and the angle of the high beam will become lower.

  7. Anonymous users2024-02-09

    Emgrand headlight height and left and right position adjustment 4 lights have a total of 8 screws, a lamp 2, one to adjust the height, one to adjust the left and right position, as long as you take a Phillips screwdriver and rotate it in the opposite direction. Open the front hood and there are two adjustment points behind the headlights, one is to adjust left and right, and one is to adjust high and low.

    The first thing to pay attention to in the left and right adjustment method of Geely Emgrand headlights is:

    1. The general adjustment of the headlights is the adjustment of high and low, and the mediation of the lights is adjusted behind the headlights in the cabin and the position of the horizontal screws;

    2. The tools to be prepared first, tape measure, sealing glue, Phillips screws and hexagon sockets;

    3. The adjustment of the height of the headlights can not be arbitrary, find a site with a flat ground and a vertical white wall - for example, it is good in the underground parking lot. You need to adjust it at night, find a place where the lighting range is more obvious, and prepare a flashlight, otherwise the screws will not be visible. Regardless of high beam or low beam, the left light is adjusted a little to the right, and the low beam is a little lower, which will make the car safer.

  8. Anonymous users2024-02-08

    1. Choose a dimly lit environment.

    For example, in the underground parking lot or at night, the front of the car is parked in front of a wall, and the front of the car is as aligned as possible with the coarse dust and bright body of the wall, about a meter apart.

    2. Turn on the headlights, cover one headlight with a thick cloth that is opaque, and adjust each headlight individually.

    In order to ensure that the position of the light beam is in the position of the normal brother grinding car, it is best not to leave the vehicle empty, and you can find a friend to sit in the driver's seat.

    3. Make a mark with a marker pen or chalk in the center of the lighting range of the headlight, and also make a mark on the wall corresponding to the position of the car logo (the center of the front of the car).

    Measure the distance between the light marks on both sides and the center position separately, and the two distances should be equal. Note: If the phenomenon of outward or inward deviation occurs, you should look at the vehicle instruction manual and use a screwdriver to make a slight adjustment so that the position of the two lights is symmetrical.

    4. Adjust the height of the beam, the right side of the light should be completely horizontally direct, and the left light should be raised up by about 10cm, but not too high, so as not to shine directly into the eyes of the opposite driver.

    Note: The range of the right side light can be shifted to the right to improve the visibility of the wide right side of the vehicle.

  9. Anonymous users2024-02-07

    Summary. Hello dear, it's a great honor to answer your questions here, let's adjust the high beam and low beam left and right. It's a pro that can be adjusted, and it can be adjusted through this adjustment bolt behind our headlights, pro.

    This is a pro that can be adjusted, here I wish you a happy life, everything goes well, this headlight behind this by the inside is to adjust the headlights left and right lights of the pro. In this innermost close to this water tank, this side of the pro,Make this adjustment, the whole headlight left and right lights can be adjusted,Pro。 Here, I wish you a happy life and all the best <>

    <> 10 years of Geely Vision that low beam how to adjust the left and right.

    Because the left side of my car can't shine out of the car.

    You are pure and pro, it is a great honor to answer your questions here, let's adjust the high beam and low beam left and right. It's a pro that can be adjusted, and it can be adjusted through this adjustment bolt behind our headlights, pro. This is a pro that can be adjusted, I wish you a happy life in this positive pants burning, everything goes well, and the inside of the headlight behind the headlight is the pro who adjusts the left and right lights of the headlight.

    In this innermost close to this water tank, this side of the pro,Make this adjustment, the whole headlight left and right lights can be adjusted,Pro。 Here, I wish you a happy life and all the best <>

    <>Hello dear, in this case, you can put this left low beam inside this close to this tank. Carry out this plum blossom clan staring to make a spin on it, dear. The torx screwdriver rotates it, and then the light can be adjusted inside, dear.

    There is a separate adjustment bolt for this adjustment behind the headlights, which can be adjusted with a Torx screwdriver. You can solve this problem pro. <>

    <>If you say that you don't know the location of Hengzhou, you take a **, and I'll mark it for you.

    Hello dear, take a look at our this is this adjustment, the light around the light of this adjustment bolt, stool spring, you use the plum blossom screw to call the rough cheats to adjust it, affinity family. <>

    <> you can adjust our lighting left and right.

  10. Anonymous users2024-02-06

    Geely's far and near light shirt is not one or rotten for a long time.

Related questions
20 answers2024-08-01

Hello, Geely Vision This model replaces the sunroof glass ** at about 400 yuan, and the deputy factory is cheap.

14 answers2024-08-01

First of all, you get what you pay for, after all, this is a low-end model, and the displacement is not very large, so the climb is relatively difficult, which is very normal, you can't be very good when running.

6 answers2024-08-01

Envision is definitely more cost-effective than King Kong, the engine Vision is all-aluminum, generation CVVT variable valve technology, King Kong is an ordinary engine, the body is iron, but King Kong's engine technology is very mature, but the engine of Vision is more fuel-efficient than King Kong; The configuration is almost the same; In terms of space, the vista is one size larger than King Kong; In terms of safety, the Envision should be better than the King Kong, after all, the Envision is the first batch of domestic cars to pass the 4-star collision. I'm using Vision now, which is great and great value for money.

8 answers2024-08-01

Hello car owner, now it is best to add antifreeze, otherwise after a period of time it will be cold, you can freeze and crack, If you have any questions, please ask, I am happy to answer for you, I hope mine can help you, I wish you a happy car [If you have a problem with the car, ask the car master. 4S shop professional technician, 10 minutes to solve. 】

27 answers2024-08-01

Hello, generally it should be that the oil pipe is not connected, and then the friction causes oil leakage, it may also be the oil pipe of the auxiliary factory, the quality is not good, or there is a problem with the oil, the oil pipe is corroded, yesterday we came here with an antifreeze added to the deputy factory, and the oil pot became sesame sauce, and the pipe was also corroded [car problem, ask the car master. 4S shop professional technician, 10 minutes to solve. 】