How to connect the external control line of the lighting digital tube is simpler?

Updated on vogue 2024-08-12
18 answers
  1. Anonymous users2024-02-16

    It should be that the signal controller cannot be connected with the new digital tube signal, unless you will replace the crystal oscillator yourself! Otherwise, the only way to do this is to replace the similar or identical digital tube.

  2. Anonymous users2024-02-15

    The IC model inside is not the same, whether the signal is correct at the corner of the wire, and the data. Locking. None of the clocks and other signals can be misconnected.

  3. Anonymous users2024-02-14

    There is generally no problem with a new digital tube, as long as it can be bright, it generally means that it is good. You can test the digital tube. I don't know what your control circuit looks like, it's generally triode controlled, you disconnect the pins of the control chip and test whether the triode can light up the digital tube correctly.

    Of course, before doing these things, it is best to test whether the power supply voltage is normal, including whether the voltage of the main control chip is normal.

  4. Anonymous users2024-02-13

    Upstairs, didn't you consider the "model" mismatch? You test whether the pin pin is the corresponding first.

  5. Anonymous users2024-02-12

    If you change the crystal oscillator, or if there is a problem with the capacitor, it is the crystal oscillator part.

  6. Anonymous users2024-02-11

    It is a mismatch between the digital tube and the controller.

  7. Anonymous users2024-02-10

    It depends on what you want. It depends on the grade you want, the simple installation and construction of the internal control is convenient and cheap. The external control is a little more high-end than the internal control.

    In addition, there are line lights, as well as DMX512 line lights. There are all kinds of them. The cheap ones are more than a dozen yuan a meter, and the expensive ones are hundreds of dollars a meter.

    Choose according to the needs of the project.

  8. Anonymous users2024-02-09

    I want to know how many meters of pipe you use.

    This makes it a good match for the controller.

    I can help you make a wiring diagram.

  9. Anonymous users2024-02-08

    By the way, it doesn't have to be 104 (, generally 103-105 is fine, and usually bigger is better.) Eliminates high-frequency radio waves. Protect the LEDs.

  10. Anonymous users2024-02-07

    It's bucked, and you can't take it that much.

  11. Anonymous users2024-02-06

    Use a 220 power cord to disconnect every six and connect to the mains power supply.

  12. Anonymous users2024-02-05

    First, there is no signal transmission, check the controller or the line.

  13. Anonymous users2024-02-04

    You asked, I didn't give any information, what lights, colorful or full color point by point? What model of controller is dressed up in? How many lines is line infiltration? There is no information in the hall to shout that you are looking for answers?? The best thing to do is to call your **ask your **quotient directly.

  14. Anonymous users2024-02-03

    There are synchronous and asynchronous ones, and there are connection diagrams

  15. Anonymous users2024-02-02

    Connect to a relatively stable high level, such as +5V (relative error <5%), or connect to the high and low level interface and point the switch to the high level.

  16. Anonymous users2024-02-01

    Connecting 1 is to connect the high level, and the terminal that needs to be connected to 1 is always given high level through the control.

  17. Anonymous users2024-01-31

    Give high to the terminal that needs to be connected to 1.

  18. Anonymous users2024-01-30

    Look for relevant documents and other materials for this. Or take a look at the technical documentation. Or go to the Big Bit forum and post to ask.

Related questions
8 answers2024-08-12

Landlord, there's a problem with the program, right?? Something is wrong with you? >>>More

6 answers2024-08-12

I don't know what the electronic basis of the questioner is. >>>More

10 answers2024-08-12

There is no such thing, and you need to draw the components by yourself. >>>More

10 answers2024-08-12

It depends on what the power supply voltage of your digital tube is, the commonly used small 7-segment digital tube is 2 LEDs in series in series, 20mA, so each section of the voltage is about, the driving current of 74HC573 can reach 35mA, the saturation voltage drop is, the saturation voltage drop and the LED working voltage add up, when the power supply voltage is 5V, the voltage will be higher, and when the current limiting resistance is not added, the current will increase to more than 35mA, so that the saturation voltage drop and LED voltage are increased, until the addition is equal to 5V. The temperature of the device increases. At this time, the sink current can not be determined, it should be beyond the normal range, and the current is related to various factors such as the size of the LED, the ambient temperature and heat dissipation, the manufacturer and batch number of the device. >>>More

23 answers2024-08-12

The river lighting should meet the needs of people who can enjoy the beautiful scenery of the river and protect people's personal safety. >>>More