What does an electric drill switch use to wash dust? How to let dust fall on yourself when using an

Updated on home 2024-08-15
12 answers
  1. Anonymous users2024-02-16

    The first step was to find a discarded Coke bottle. For example, our mineral water bottles, Coke bottles! and other bottles!

    Bottles like this should not be thrown away or sold in daily life. Of course, you can't sell it for a few cents, and if you change it slightly, it will become an anti-ash artifact of an electric drill.

    In the second step, you'll need to get a utility knife and split the plastic bottle in two.

    Plastic bottles actually have a lot of wonderful uses in our lives, and today we only need to use the bottom section of the plastic bottle.

    The third step is to make a cable-stayed mark for the Coke bottle with a marker.

    You have to compare the Coke bottle with your hand and then draw the Coke bottle diagonally with a marker and divide it into two triangles. The Coke bottle should be marked on both sides and be symmetrical.

    The fourth step is to use scissors to cut it along the mark.

    After cutting the Coke bottle along the mark, it is a beveled Coke bottle.

    Then follow this diagonal line to make him attach to the wall. He's a dust collector! At this time, we need to tear the advertising sticker on the Coke bottle to him, so that it is more convenient for us to observe the gray condition inside.

    The fifth step is to carve a hole in the middle of the straight side of the Coke bottle.

    This hole is the size of the drill bit on our electric drill. The diameter is the same. We're going to have our drill bit going through here later.

    Step 6: Thread the drill through the Coke bottle.

    Then find the location of the wall where you want to make a hole, drag the Coke bottle with one hand and let him idle to cling to the wall, and hold the electric drill in the other hand to drill.

    You'll notice that some of the fly ash from the oil drill is blocked, if it's in this one Coke bottle. It didn't fly out at all, it was very clean, and there was no fly ash in the air.

    When cutting, be sure to cut it smoothly so that it can be completely attached to the wall. Just such an electric drill ash preventer. So that you can use the electric drill at home with confidence, and you don't have to do a lot of hygiene every time!

    Watch all the dust from the electric drill fall into this Coke bottle. When you're done, all you have to do is remove the ash from the Coke bottle.

  2. Anonymous users2024-02-15

    Fall? Or still won't drop? It's as simple as dropping, just stand under the electric drill. If you can't think of it, you can use cardboard to make a self-made dust cover and put it on the part of the drill bit that does not rotate.

  3. Anonymous users2024-02-14

    Drill holes in the wall at home, dust is scattered and it is not easy to pick up, then use a hard A4 paper to stack and glue a long box (storage box), the box is similar to the L-shaped point on one side, and the upper mouth of the growing side is pasted with tape under the perforation, and then punch the hole and catch the dust.

    Note: Do not stick too much to glue the wall.

  4. Anonymous users2024-02-13

    Use a vacuum cleaner while drilling the holes. Without a vacuum cleaner, you can fold it into an L shape with cardboard paper and stick it under the drilling position.

  5. Anonymous users2024-02-12

    The best way is to put the hose of the vacuum cleaner under the drill bit when punching, open the vacuum cleaner to punch the hole, and the powder from the hole will be sucked away

  6. Anonymous users2024-02-11

    The way to keep dust out of the air is to add a guard before turning your head. The annual production and sales of electric drills account for 35% of China's power tools. The specifications of the electric drill are also divided into a very variety, and the number points to the maximum diameter of the drill bit drilled on the steel with a tensile strength of 390n mm2, and the maximum drilling diameter of the hole for materials such as metal and plastic can be 30 50% larger than the original specification.

  7. Anonymous users2024-02-10

    Add a guard before turning your head.

    The annual production and sales volume accounts for 35% of China's power tools. The main specifications of the electric drill are mm, etc., and the number refers to the maximum diameter of the drill bit drilled in steel with a tensile strength of 390n mm2. The maximum drilling diameter of non-ferrous metals, plastics and other materials can be 30 50% larger than the original specifications.

    Classification: Electric drills can be divided into 3 categories: hand drills, percussion drills, and hammer drills.

    1.Hand drill: the power is the smallest, and the scope of use is limited to drilling wood and being used as an electric cone, which does not have much practical value.

    2.Percussion drill: The percussion mechanism of the percussion drill has two kinds of electric drills: canine type and ball type electric drill.

    The ball impact drill is composed of a moving disc, a fixing disc, a steel ball, etc. The moving plate is connected to the spindle by a thread and is equipped with 12 steel balls; The fixing disc is fixed to the casing by pins and carries 4 steel balls, under the action of thrust, 12 steel balls roll along the 4 steel balls, so that the cemented carbide drill bit produces a rotational impact motion, and can drill holes in brittle materials such as bricks, blocks, and concrete. Take off the pin, so that the fixing disc rotates with the moving disc without impact, and can be used as an ordinary electric drill.

    3.Hammer drill (electric hammer): can drill holes in any material, the most widely used.

    These 3 kinds of electric drills are arranged from low to high, and the functions are also increased, and the selection needs to be combined with their respective scope of application and requirements.

  8. Anonymous users2024-02-09

    The way to keep dust out of the air is to add a guard before turning your head. The annual production and sales of electric drills account for 35% of China's power tools. The specifications of the electric drill are also divided into a very variety, and the number points to the maximum diameter of the drill bit drilled on the steel with a tensile strength of 390n mm2, and the maximum drilling diameter of the hole for materials such as metal and plastic can be 30 50% larger than the original specification.

  9. Anonymous users2024-02-08

    The drill punches a lot of dust, teaches you three tricks, how to use water skillfully, very practical, learned is earned.

  10. Anonymous users2024-02-07

    There is no good way, introduce a way to collect dust when punching, you can try it 1 First prepare a relatively wide transparent tape Plastic bag Scissors plastic bag Choose a larger or smaller one according to the size of the drilling.

    2. Spread one side of the bag, then cut a piece of transparent glue and stick it to the mouth of the bag, and the length of the transparent glue is roughly cut off according to the length of the mouth of the bag.

    3 Stick the bag flat on the wall below the nearest position to the hole to be drilledNote: the transparent glue should be flattened and there should be no wrinkles, so that it will not hinder the dust and slide naturally, and the bag should be stretched open, so that the powder layer that floats out will also be better collected.

  11. Anonymous users2024-02-06

    Use a transparent plastic sheet and a damp cloth to make a dust cover similar to the bell mouth when you turn it on the machine, not only dustproof but also reduce noise, refer to the desk lamp shade The outer layer of transparent plastic is pasted with the inner layer of cloth (remember to leave an observation hole) When you use it, soak the cloth (be careful to go electric) and put it on the wall on the electric turner. If you can, it is recommended to buy an air filter, or make your own. Works great,

  12. Anonymous users2024-02-05

    Drill while using a vacuum cleaner.

Related questions
15 answers2024-08-15

In my experience: ** useBaking soda + toothpaste + dish soapSoak and clean it can be easily cleaned, and there is no damage to **, and, I have personally tried many times, simple and convenient, we take **necklace as an example to make a **Ming: >>>More

11 answers2024-08-15

At present, the main methods of tattoo washing are laser tattoo washing, as well as the ** grinding method, but compared with each other, the effect of laser tattoo washing is even better! Compared to laser tattoo removal, grinding is a more traditional method. It is suitable for removing shallow tattoo patterns, and there may be ** pigmentation or loss of pigment after tattoo washing; Removal of scars left when it is too deep, and it is difficult to completely remove dark pigments. >>>More

13 answers2024-08-15

You can pour water and white wine into the basin, and then put the crab in and soak it for about 10 minutes, so that the crab will be drunk. It is not easy to get caught in the hands when cleaning crabs. Then grab both sides of the crab and vigorously wash the back, abdomen and mouth with a toothbrush; Then clean the sides of the crab and the roots of the feet and tongs; Then use the handle of the toothbrush to pick up the joints of the double tongs from the bottom up, and use the thumb and index finger of the crab catcher to grasp the crab claws along the root of the tongs upward. >>>More

5 answers2024-08-15

1. First prepare a basin of water, and then sprinkle an appropriate amount of baking soda in it. >>>More

10 answers2024-08-15

The most convenient way is to have tea stains.

Immerse the cup in water for 2 minutes, then take it out, dip some toothpaste with a toothbrush, evenly apply the toothpaste to the place with tea stains, and then wipe it repeatedly for about 3 minutes. >>>More