How to partially remove the gusset ceiling, how to dismantle the PVC gusset ceiling?

1. Square aluminum gusset: You can use a very thin blade tip to gently insert the corner gap of the gusset plate, try to move it down, dial a little bit, dial the other diagonal side of the gusset plate in the same way, and then dial the diagonal edge of the other pair of sides, repeat several times, you can disassemble the square aluminum gusset. 2. Square aluminum gusset:

The removal of the square aluminum gusset can also be pulled down from the edge with a suction cup, or pry down from the edge with a small flathead screwdriver. 3. Long aluminum buckle plate: The long aluminum buckle plate can be removed from the last board, and then removed in turn.

4. Long aluminum buckle plate: The long single buckle aluminum buckle plate can be pry down the edge of the single piece with a small slotted screwdriver, and the single piece of the buckle plate can be removed individually.

Dismount with the help of suction cups, flathead screwdrivers, or a relatively thin piece of iron.

1. Square aluminum gusset: Do it yourself, you can buy a suction cup first, use the suction cup to stick to a corner of the square, and then pull the corner of the aluminum gusset hard, and the other three corners can be dismantled in the same way, so that the labor cost of disassembly can be effectively removed.

Strip aluminum gusset: When installed, it is pressed one by one, and the last one will probably have a small seam of centimeters. Insert the wallpaper knife along the gap, draw back and forth a few times to find the position of the clip, and then gently pry downward, pry the middle first, pry both sides are easy to deform.

Gently pry it vigorously, and then disassemble it from the side in turn.

Material gusset ceiling removal method:

1. To remove the plastic ceiling, remove the pressing strip at one end, extract the plate from the pressing strip block by piece, replace the damaged plate with a new plate, and then reinstall the pressing strip. Pay attention to minimize color difference when replacing. Precautions for the removal of plastic ceilings (it is recommended to ask a professional master to remove them, so as not to break the plastic ceiling).

2. When the plastic ceiling is removed, the safety of the equipment and facilities in the original ceiling should be considered to avoid damage to the pipeline and equipment during the demolition; When removing the original ceiling in the kitchen and bathroom, it is necessary to avoid damaging the ventilation duct and flue; The original circuit pipeline in the ceiling should be removed as much as possible, and no longer considered for continued use.

3. The design of second-hand houses should give priority to the safety of suspended ceilings. In particular, some old houses that have been used for more than 15 years, their original building structure has begun to age, and due to the requirements of the hanging structure during the construction of the original ceiling, many holes have been made on the top surface, so that the local bearing capacity has decreased.

4. The demolition and transformation of the plastic ceiling in the kitchen and bathroom should pay attention to the impact on the indoor light source, and the height of the ceiling should be moderate, which will have an impact on the wall decoration and the soft decoration in the future.

5. The echoing relationship between the plastic ceiling and the ground must also be paid attention to, and when the ground function and the ceiling are asymmetrical, it will affect the placement of furniture and other furnishings in the future.

1. First of all, insert the wallpaper knife along the gap, draw back and forth a few times to find the position of the clip, and then gently pry downward, pry the middle first, and pry the two sides are easy to deform.

2. The aluminum buckle plate with long strips and buckles needs to be removed from the last board and then removed in turn; The long single-buckle aluminum gusset can be pryed down the edge of the monolithic piece with a small flathead screwdriver, and the monolithic gusset can be removed individually.

3. See if the PVC board and trimming corners are made of glass glue during installation, and if so, cut it with a utility knife. Then insert a flathead screwdriver or utility knife into the gap between the last piece and the penultimate one, and gently move it up and down, and after a while, the last PVC board will be loosened.

4. Use a Phillips screwdriver to remove the board inside, because the mother seam of each PVC board will be self-tapping screws, first under the self-tapping screws, and then slowly disassemble them, don't break them. Finally, open the smoke pipe hole, first put the removed plate according to the direction, and then make a mark where the smoke pipe hole needs to be opened, and then put the purchased pipe vertically at the mark, draw a circle along the smoke pipe with a paint pen, and then use a hole opener to open the hole.

First, first of all, you see if the PVC board and trimming corners are made of glass glue when installing, and if so, use a utility knife to cut it. Then insert a flathead screwdriver or utility knife into the last and penultimate gaps, gently swing up and down, and after a while, the last PVC board will be loose, you will push the board to the left or right of the trimming corner, and there will be one side down, and then grab the side with both hands, gently press down, use a little force, pull, and it will come out.

Second, and then dismantle the board inside, you need a Phillips screwdriver, because the mother seam of each PVC board will be self-tapping screws, first under the self-tapping screws, and then slowly disassemble, do not break.

3. Finally, open the smoke pipe hole, first put the removed board according to the direction, (be sure to press the direction) Oh, and then make a mark where you need to open the smoke pipe hole, and then put the purchased pipe vertically at the mark, use a paint pen to draw a circle along the smoke pipe, and then use a hole opener to open the hole. After doing a good job, install it according to the original path, and lay glass glue around it, just do it.

1.For this kind of gusset ceiling, usually only need to use a hook suction cup to suck the middle of the gusset, gently pull it down, it is easy to remove the gusset, which is the easiest way. 2.

Another form of gusset is the strip gusset, for this form of gusset, we can use a small iron piece or wallpaper knife, insert into the gap of the gusset, back and forth to the collapse of the hole a few times, find the part of the clip in the gap, and then we only need to gently pry down, in the middle of the force, to prevent both sides from bending and deforming. 3.If it is a long buckle plate, find the buckle part, use a small iron piece to cut the buckle part, remove it from the last board, and then remove the front buckle plate in turn, if it is a long strip trembling rent single buckle aluminum buckle plate, you can use a flathead screwdriver to pry it down along the edge of the single piece, you can remove the single piece of buckle plate.