Automatic sandblasting machine, sand waste is fast, what is there to solve it

It is common for automatic sandblasting machines to waste sand quickly during use. In response to this problem, the following methods can be taken to solve it:

1.Adjust the parameters of the sandblasting machine: The speed of sand waste can be controlled by adjusting the sandblasting pressure, sandblasting speed, sandblasting angle and other parameters of the sandblasting machine. According to the specific work requirements, reasonable adjustment of these parameters can achieve higher blasting efficiency and reduce the generation of sand waste.

2.Optimize the choice of blasting material: Choosing the right blasting material is also an important factor in reducing sand waste. Different sandblasting materials have different hardness and wear resistance, and choosing the right sandblasting material for the work needs can extend its service life and reduce the generation of sand waste.

3.Regular maintenance and cleaning: Regular maintenance and cleaning of your blasting machine is key to keeping it up and running and extending its lifespan. Cleaning up the impurities and accumulations inside the sandblasting machine and keeping the sandblasting machine smooth and working normally can reduce the generation of sand waste.

4.Use ancillary equipment: During the blasting process, consider using some ancillary equipment to reduce the generation of sand waste. For example, a vacuum cleaner or collection device can be used to collect sand waste from the blasting process, reducing its scattering and waste.

In short, by reasonably adjusting the parameters of the sandblasting machine, selecting the appropriate sandblasting materials, regular maintenance and cleaning, and using auxiliary equipment, the problem of fast sand waste of the automatic sandblasting machine can be effectively solved, the sandblasting efficiency can be improved, and the cost can be reduced.

There are several reasons why the sand of the sandblasting machine is wasted quickly: 1. The sand material is not selected correctly; 2. The sealing performance of the sandblasting machine is not good; 3. The sand is sucked away by the dust removal box;

Find the cause to solve it. Baiyuan sandblasting machine wishes you a prosperous business!

I don't know what kind of sand you use? What is the material of the product that needs to be sandblasted?

There are many reasons that affect the sandblasting effect of automatic sandblasting machine, mainly including the following aspects:

1.Selection of blasting material: Different blasting materials have different hardness, particle size, and shape, and choosing the right blasting material is crucial to achieving the desired blasting effect.

2.The blasting pressure and blasting volumeThe size of the blasting pressure and blasting volume directly affects the sandblasting effect. Too high a blast pressure can cause excessive wear on the surface, while too low a blast pressure may not achieve the desired cleanup.

3.Blasting distance and angle: The choice of blasting distance and angle will also have an impact on the blasting effect.

Blasting distances that are too close may cause excessive surface wear, while blasting distances that are too far away may not achieve the desired cleaning results. The choice of blasting angle also needs to be carried out on a case-by-case basis, and the blasting can evenly cover the entire surface.

4.Sandblasting time and blasting speed: The control of sandblasting time and blasting speed is also an important factor that affects the sandblasting effect. Blasting too long can lead to excessive surface wear, while blasting too fast may not achieve the desired cleanup.

5.Preparation before surface treatment: Before blasting, the surface to be treated needs to be thoroughly cleaned and prepared to ensure the best blasting effect. This includes the removal of oil, rust, and other impurities from the surface, as well as necessary repairs and coatings.

To sum up, there are many factors that affect the sandblasting effect of the automatic sandblasting machine, and it is necessary to comprehensively consider all aspects of the factors, and make reasonable adjustments and controls to achieve the ideal sandblasting effect.

The sandblasting effect of an automatic sandblasting machine is affected by a variety of factors, and here are a few of the common ones:

Nozzle: Nozzle is an important part of the sandblasting machine, and the aperture and angle of the nozzle will directly affect the flow, speed and range of sandblasting. If the nozzle aperture is too small or the angle is incorrect, it will lead to problems such as uneven blasting and insufficient strength.

Blasting Pressure: Blasting pressure is a key factor in controlling the speed and intensity of blasting. If the blasting pressure is too low, the sand particles sprayed out are not fast enough to achieve the desired cleaning effect; If the blasting pressure is too high, it will cause wear and tear of the sandblasting machine, and the sandblasting is also easy to be excessive, causing damage to the object being treated.

Types of sand grains: Different types of sand grains will produce different cleaning results. For different objects to be treated, it is necessary to select the appropriate type of sand grains.

Sandblasting distance and sandblasting time: Sandblasting distance and sandblasting time directly affect the sandblasting effect. If the distance is too far or the time is too short, the sandblasting effect is not ideal; If the distance is too close or too long, damage may be caused to the object being treated.

Material and shape of the object to be treated: The effect of the treated object on the blasting machine will be different for different materials and shapes. It needs to be adjusted according to the material and shape of the object being processed.

The above factors will affect the sandblasting effect of the automatic sandblasting machine, which needs to be adjusted and optimized according to the specific situation.

The sandblasting machine uses compressed air as the power, and the sand and gas are mixed to form a high-speed jet beam to spray the sprayed material along the conveying pipeline at high speed, and spray it to the surface of the workpiece to be treated, so that the attachment on the surface of the workpiece to be treated is peeled off and separated, or the mechanical properties of the outer surface are changed.

Scope of application. It is suitable for sandblasting processing of flat plates, plates, quadrangles, profiles and other special-shaped workpieces, such as: flat stainless steel plates, parallel steel plates, glass fiber reinforced plastic plates, stones, non-stick pans, baking trays, toaster ovens, computer chassis, functional panels, notebooks, computer motherboards, iron bottom plates, decorative parts, signage badges, communication equipment, aluminum plates, profiles and other special-shaped parts.

There may be several reasons why the sand blasting machine is not effective:

Nozzle clogging: If the nozzle is clogged with sand particles or other debris, it will cause the sand blasting machine to have a poor sand suction effect. At this time, it is necessary to stop the nozzle to clean it.

High sand humidity: The high sand humidity of the sandblasting machine will affect the fluidity of the sand and lead to poor sand suction effect. The solution is to dry the sand.

The particle size of the sand is too large or too small: If the particle size of the sand is not suitable for the nozzles and pipes of the blasting machine, it will affect the sand suction effect. It is necessary to select the appropriate sand according to the requirements of the sandblasting machine.

Insufficient pressure: If the pressure output of the air compressor is insufficient, it will affect the sand suction effect of the sandblasting machine. It is necessary to check whether the output pressure of the air compressor meets the requirements of the sandblasting machine.

Sand adheres to the inner wall of the pipe: If the sandblasting machine is not used for a long time, the sand may adhere to the inner wall of the pipe, resulting in poor sand absorption. This is where the pipes need to be cleaned.

In short, the poor sand suction effect of the sandblasting machine may be caused by a variety of reasons, and it is necessary to analyze the specific problems, find the causes and take corresponding solutions.

The sandblasting nozzle is blocked (not completely blocked, so it can not produce enough negative pressure, and the sand can not suck the sand), or the sand suction pipe is damaged and leaking, in short, there is a leak or blockage, and the problem will be found by careful inspection, and there is not enough wind pressure or flow is not enough, and the general pressure at the open end is more than two pressures to use. That is, there must be a large air compressor to drive the sandblasting machine to do it.

Sandblasting rust removal is the use of compressed air, a certain particle size of sand sprayed on the rusted surface of the parts through the spray gun, not only fast rust removal, but also for painting, spraying, electroplating and other processes to prepare the surface, sandblasted surface can achieve clean, a certain roughness of the surface requirements, so as to improve the binding force of the covering layer and the parts. The compressed air used for sandblasting must be treated by a cooling device and an oil-water separator to ensure dryness and oil-free air; Oil-water separators must be cleaned regularly. The distance between the nozzle and the surface of the base steel should be 100 300mm, and the non-sandblasting parts should be shielded and protected before sandblasting.

There may be several reasons why the sandblasting machine suddenly can't spray sand:

1.Sand clogging: During the use of the sandblasting machine, the sand may block the nozzle or sandblasting pipe, resulting in the inability to spray sand normally.

This may be due to the presence of impurities or excessive particles in the sand, clogging the nozzles or pipes. The solution is to clean the nozzles and pipes to ensure that the sand is clear.

2.Insufficient pressure: The sandblasting machine needs a certain pressure to spray the sand, and if the pressure is insufficient, it will not be able to blast the sand normally.

This may be due to the incorrect setting of the pressure regulator of the blasting machine or insufficient compressed air**. The solution is to check the settings of the pressure regulator to make sure that the pressure is appropriate and that the compressed air** connected to the blast machine is sufficient.

3.Nozzle wear: The nozzle of the sandblasting machine may wear out after a long period of use, resulting in the sand being unable to be sprayed properly. At this point, the nozzle needs to be replaced to ensure that the size and shape of the nozzle meet the requirements.

4.Sand depletion: The sandblasting machine uses a limited amount of sand, and if the sand is exhausted, it is impossible to continue blasting. The solution is to replenish the sand in time to ensure that the sandblasting machine has enough sand**.

In conclusion, the sudden failure of the sandblasting machine to spray sand may be caused by clogged sand, insufficient pressure, worn nozzles, or running out of sand. Depending on the specific situation, corresponding measures can be taken to solve the problem. If you can't solve it on your own, it is recommended to ask a professional for overhaul or repair.

1. The sand is wet but not dry.

2. Sandblasting or abrasive valve blockage.

3. The safety gas path is cut off.

4. The main pressure regulator is broken.

5. The pressure regulator valve for control is broken.

6. The foot switch is not adjusted well or damaged.

These reasons are possible, you can go to our** to find out, you can use the search Zhaoshun sandblasting machine**, directly send the link can not be sent, sorry, there is a lot of knowledge about sandblasting, you can also consult me if you have any questions.

Summary. Hello dear The nozzle of the automatic sandblasting machine is blocked by foreign objects: after the blasting department machine is deflated, first turn the nozzle sleeve down to check whether the sandblasting nozzle is blocked by foreign objects, and if so, remove the foreign bodies.

Note: When the nozzle sleeve is turned away from the iron base, the nozzle must be turned upwards and then tapped a few times before it can be rotated, otherwise it is easy to cause the screw teeth to bite or be damaged).The sandblasting abrasive of the automatic sandblasting machine is not suitable for excessive dust or very large particles:

Unsuitable abrasives are easy to accumulate dust or clog the sand nozzle, it is advisable to choose an abrasive without dust and uniform particle size distribution. The reason why the general automatic sandblasting machine cannot absorb sand, does not produce sand or has small sand is mainly because the sandblasting nozzle of the sandblasting tank is blocked (not completely blocked), and it cannot produce enough negative pressure to suck the sandblasting abrasive.

What is the reason for the unstable sand output of my sandblasting machine, please help.

The nozzle of the automatic sandblasting machine is blocked by foreign objects: after the sandblasting department is deflated, turn the nozzle sleeve down first, check whether the sandblasting nozzle is blocked by foreign bodies, and if so, remove the foreign bodies. (Note:.)

When the nozzle sleeve and the iron seat are rotated, the nozzle must be turned upwards and then tapped a few times before it can be rotated, otherwise it is easy to cause the screw teeth to bite or be damaged).The sandblasting abrasive of the automatic sandblasting machine is not suitable, the stool cover is too dusty or has very large particles: the unsuitable abrasive is easy to accumulate dust or block the sand nozzle, it is advisable to choose an abrasive without dust and jujube cavity, and the particle size is evenly distributed.

The reason why the general automatic sandblasting machine cannot absorb sand, does not produce sand or has small sand is mainly because the sandblasting nozzle of the sandblasting tank is blocked (not completely blocked), and it cannot produce enough negative pressure to suck the sandblasting abrasive.

What is the reason for the sand one by one.

If the sand flow is too large or the compressed air is too small, the sand will be ejected (shivering) one by one

Shaking all the time, what the reason.

This is the case with a jar of sand.

What's a good solution? Thank you!

Hello, try to adjust the flow of small sand.

I can't even adjust it.

1. Does your sandblasting machine have a sand adjustment pump? Let the sand pump be adjusted to a large age, and the sand pump should have a vent, so that the sand will not be breathless. 2. If the air pressure is too large, the sand material cannot keep up, there will be such problems 3, whether the air pressure is stable 4, whether the sand is damp 5, and whether the nozzle is leaking.

None of these problems exist.

The pressure is unstable, there is a blockage, and the sand tide imitates the macro and so on. The air pressure is not enough, the wind power of the dust collector is not enough, and the abrasive is not circulating. In addition to the above problems, there may also be wet sand, or there is not enough sand.

You see if there are any of these problems.

Summary. Hello dear! 1. The air pressure is not enough; 2. The wind power of the dust collector is not enough; 3. Your abrasives are not circulating enough. In addition to the above problems, there may also be wet sand, or there may be insufficient sandblasting machine in Ningbo.

What is the reason for the unstable sand output of my sandblasting machine, please help.

Hello dear! 1. The air pressure is not enough; 2. The wind power of the dust collector is not enough; 3. Your abrasives are not circulating enough. The sandblasting machine may have such as the question of Yingsong on the Qiao Song mold, there may also be wet sand, or filial piety is not enough sand and other Ningbo sandblasting machine.

Hello dear! The sandblasting machine is unstable, generally the pressure is unstable, there is a quick blockage, the sand is tide and so on. The air pressure is not enough, the wind power of the dust collector is not enough, and the abrasive is not circulating.

In addition to the above problems, the sandblasting machine may also have wet sand, or the sand material is not enough.

What is the reason for the sand to come out one by one?

Ask about custom messages].

Ask about custom messages].

Ask about custom messages].

Ask about custom messages].

Okay, wait a minute.

The speed of sandblasting will have a certain impact on you, because the empty source is not the same as blasting. Sandblasting is the use of the gun head strafing, which takes a certain amount of time, and the shot blasting head is fixed, so there is no such situation.

Hello dear! First of all, see if the sand pipe nozzle is blocked.

It's not blocked. The speed of sandblasting will have a certain impact on you, because the empty source is not the same as blasting. Sandblasting is the use of the gun head strafing, which takes a certain amount of time, and the shot blasting head is fixed, so there is no such situation.

The out-of-air pressure is high. As soon as the sand comes out, it will be one by one.