-
Anonymous users2024-02-15The use of electric oil tins.
The electric heater is equipped with a thermostat, so that the surface temperature of the heater housing can be adjusted at will (below 120). When working normally, the thermostat should not always be set to the highest gear, otherwise when the surface working temperature of the heater is close to 120, the thermostat is not easy to operate, and the internal components are easy to burn and age or the protection is damaged when working at high temperature for a long time.
Maintenance of the electric oil tin.
1. Pay attention to maintaining tightness. The indoor sealing is good, and after the room temperature rises, the heating time is short and the heat dissipation time is long, so as to save electricity.
2. Prohibition of overlay. If the heat sink is wrapped around the surface for baking, the temperature of the covered hot sheet will be significantly higher than the temperature felt by the bimetal sheet in the surface, which is easy to scorch the clothes and cause danger.
3. It is forbidden to turn up and down. Inverted or downsided, the internal heating tube exposes the oil surface, in this case, the electric heating may produce over-burning and bursting, damaging the heating tube.
-
Anonymous users2024-02-14When adjusting, first gently rotate the thermostat knob clockwise to the maximum position, turn on the two-speed power switch (the high-power oil heater has three gears), the whole machine is in the maximum output state, heat up for about 5 minutes, and gently pat the upper surface of the shell with the back of your hand.
If you feel the right temperature, gently rotate the knob in an anti-clockwise direction until there is a crisp contact pop-up sound, and the power indicator on the power switch turns off, then gently turn it clockwise at a small angle to prevent the contacts from closing.
Once this is done, the heater can provide a satisfactory temperature. The temperature of the surface of the shell is about 85 when it is slightly hot. If the temperature of the heater housing is higher than the set temperature, the thermostat will automatically cut off the power supply to stop heating, and the heat stored inside will continue to be released to the outside.
When the surface temperature drops by 15, the thermostat contacts will automatically close, and the heating will be heated by electricity, and when the temperature of the shell is higher than the set temperature, the heating will be automatically cut off and stopped. And so on and so forth, and the temperature is balanced.
-
Anonymous users2024-02-13The electric oil tins are easy to use; When the electric heating oil is used for heating the living room, it should be as close as possible to the position of air convection, which is both warm and energy-saving. Since the surface temperature of radiator type oil heater can be as high as about 85 degrees Celsius when working, when used for bedroom heating, it should be avoided as much as possible from people's heads. If there are small children in the house, they should be placed in a place that is not easily accessible to children, or some protective equipment should be added around them to prevent children from getting burned while playing.
IntroductionElectric oil heater, referred to as electric oil heater, is a kind of oil-filled heater, which is a safe and reliable space heater that has become popular in recent years. It is mainly composed of sealed electric heating elements, metal heating tubes, iron heat sinks, temperature control elements, power switches, indicator lights, etc. This kind of heater is to install the electric heating pipe inside the cavity of the heat sink, and the heat transfer oil is injected around the electric heating pipe in the cavity.
When the power is connected, the heat transfer oil around the electric heating pipe is heated, rises to the upper part of the cavity, circulates along the convection of the heat pipe or heat sink, and radiates the heat out through the surface of the cavity wall, thereby heating the space environment. The air-cooled heat transfer oil descends around the electric heating pipe and is heated again, starting a new cycle. These heaters are usually fitted with a bimetallic temperature control element that disconnects itself when the oil temperature reaches a set temperature.
-
Anonymous users2024-02-121. Regular weighing: The electric oil tin itself is heated with heat transfer oil, and then circulated to achieve the purpose of raising room temperature, and the inside contains a certain amount of heat transfer oil. If there is a leakage phenomenon in the electric oil tin, it will cause the use effect to deteriorate and even have potential safety hazards, so you can use regular weighing to determine whether the electric oil tin has leakage wheel tracks.
2. Placement: When using the electric oil tin, it is best to place it in a position with strong air convection, so that the use effect of the electric oil tin can be maximized, and it will be more energy-saving. In addition, because the surface temperature of the oil tin will be relatively high when working, it needs to be placed in a position that cannot be easily touched by children to avoid burns.
3. Upright placement: Do not use strange ways such as upside down, flat or oblique placement of electric oil tins. Because the heating element of the electric oil tin is often at the lower end, if it is not placed upright, it may cause the electric oil tin to burn in the air, resulting in its damage.
4. Avoid indiscriminate refueling: Because the oil used in the electric oil tin is relatively special, even if the oil tin is damaged and leaking, do not add oil indiscriminately, and mixing other varieties of oil is likely to cause unknown accidents. Therefore, if it is determined that there is a leak in the electric oil tin, you must ask a professional after-sales personnel to repair it.
-
Anonymous users2024-02-11The electric oil heater is equipped with a thermostat, so that the surface temperature of the heater shell can be adjusted at will (below 120). During normal operation, the thermostat should not always be set to the highest setting. 2.
When adjusting, first gently rotate the thermostat knob clockwise to the maximum position, turn on the two-speed power switch, the whole machine is in the maximum output state, and the heating temperature rises for about 5 minutes. 3.Once this is done, the heater can provide a satisfactory temperature.
The temperature of the surface of the shell is about 85 when it is slightly hot. The temperature of the heater housing is higher than the set temperature.
How to use the insect detection and alarm light:
The insect detection and reporting lamp automatically takes pictures, automatically dries, automatically turns on the light, and can automatically open the lamp and high-voltage network remotely; Equipped with remote software platform, PC and mobile phone. >>>More
To ensure the normal operation of an automatic winding machine, daily inspection and correct operation is an indispensable important step, first of all, the equipment manual should be established, which is used for daily recording and reading of the operation of the automatic winding machine and the existence of problems, when starting to work, it is necessary to carefully check the workbench, the wire guide rail and the main sliding surface, if there are obstacles, tools, impurities, etc., it must be cleaned, wiped clean, oiled, and carefully check whether the equipment moving mechanism has new pulling, grinding, and bruising. If there is, the equipment staff should be notified to check whether the analysis is caused by the fault, and make a record, check the safety protection, power supply, limit and other devices should be complete and intact, check that the electrical distribution box should be closed firmly, the electrical grounding is good, and check whether the accessories of the equipment are good. The wire wheels, felt clamps, pay-offs, ceramic parts, etc. should be complete and intact, installed correctly, and the idling operation test should be observed to see whether the operation is stable, whether there is abnormal noise, etc. Although the above work is cumbersome, it can effectively judge whether the equipment is in good condition and prevent the occurrence of failures. >>>More
When you plug your teeth after eating, you can use dental floss to effectively remove the food residue between the teeth, solve the discomfort of the three teeth, and feel that after brushing your teeth at night, you can remove the food residue and plaque to prevent the appearance of dental diseases. >>>More
1) Transportation and storage of vibrating feeders.
Vibrating feeder transportation: When the transportation feeder is loaded and unloaded, it can be hoisted by using the chassis trunnion; The center position of the steel plate on the feeding surface of the feeder is welded with a lifting eye, which can be used for hoisting during on-site installation, and the vibrating feeder will be cut off after it is installed in place. >>>More
The correct way to use toner: Use toner after each face cleansing, remember not to pat your face directly, because this will cause bacteria on your hands to infect your face, and in addition, the toner has been lost before it has been absorbed by your face**. You can pour the toner onto a cotton pad and wipe it along the texture of the skin from the inside out. >>>More