What does it mean for Inovance server to display RDG?

The display symbol of the server is that the background running speed of the server is significantly reduced, and there is no way to support the normal work.

So we have to check the frequency of operation in time and adjust the voltage**.

If the servo motor shows this, there should be a fault**, so you can restart it directly, and then it can be recovered.

If the server will display RGDG, it means that the server equipment is faulty, and it will be good to restart.

This is actually the case where he is showing an error on the server.

The abbreviation of ready, which means that the servo is ready, but it is not yet running, and it is in standby mode.

What a bunch of people are doing? The Inovance servo drive displays RDY mainly because the servo is not enabled.

Because that's what the products in Guizhou show, and some of them in Guizhou may not be used in other places or outside the province.

No, yes, what do you mean? The only master she can turn around is probably that variety, and that watch.

The display of the Inovance server can be consulted with the after-sales personnel of the shopkeeper, and they will provide this information.

What does the Inovance server mean when it shows the pair of headphones, this seems to be an uh logo or a model number, it should be the meaning of the model.

What does it mean when Inovance server shows RDG? I think this kind of circuit may be caused by the instability of the circuit, and I think you can consult a professional like this.

What does the monitor show for this? There was also a little problem with the hot display, and the color was wrong.

The meaning of this sentence is that there is a problem with the monitor, there is a problem with the system, and you need to repair it, do you still have any problems? Thank you for your support.

In this case, it is very likely that your motherboard has a faulty key, and you replace it without publishing, and then try again, which can generally solve the problem.

Then about Inovance servo oil and gas, if it displays the alarm, you can see the manual, he has that manual, ask about the situation, and really call ** consultation in the frequency band.

Uh, this should be the police, right? The light of the display should be alarmed, you can take a look at the servo It has a manual, four or five manuals in which he will tell you how to use it to solve it.

The RDD displayed by Inovance's server is not very clear, and it is probably a symbol of a failure.

Generally, the system is faulty.

It is recommended to go to the official after-sales inspection and repair.

Summary. Hello, 1. The bus voltage of the control loop is too low: use a multimeter to confirm whether the power supply voltage value of the control loop (L1C, L2C) is too low.

The phase-to-phase voltage of the 220V class driver is lower than 198V, and the phase voltage of the 380V class driver is lower than 342V, which will cause the bus voltage to be too low. Read the control loop bus voltage monitoring value (H0B57), 220V class driver is below 235V, 380V class driver is below 451V between phases.

2. Whether the input voltage meets the requirements. Using a multimeter, confirm the voltage value of the main circuit (r, s, t) or the input voltage of the three-phase phase.

3. Whether the bus voltage meets the requirements. Through H0B-26, you can check whether the bus voltage value of the main circuit of the driver is consistent with the measured bus voltage; Whether the power-on bus voltage is too high or too low, and the pn voltage meets the following requirements* (1 15%) 2 * 1 10%) 2 in min pn in max v v v.

4. Detect that the speed feedback exceeds 10rpm when the power is on, and confirm whether there is any reverse drag or abnormal encoder feedback H0B07.

5. Abnormal wiring. When the IS620P-Sizee frame machine is wired, it is necessary to connect the negative bus short connector of the power terminal, otherwise it will alarm NRD, and the Inovance servo power-on display RND? What is the meaning.

Hello, I am helping you to inquire about the relevant information and will reply to you immediately.

What does Inovance servo power-on display rnd mean.

Hello, it doesn't work properly.

I also know what the alarm is**.

The bus voltage of the control loop or main loop is too low or the speed feedback is abnormal.

How to fix it. Hello, 1. The bus voltage of the control loop is too low: use a multimeter to confirm whether the power supply voltage value of the control loop (L1C, L2C) is too low.

The phase-to-phase voltage of the 220V class driver is lower than 198V, and the phase voltage of the 380V class driver is lower than 342V, which will cause the bus voltage to be too low. Read the control loop bus electric damage hole pressure monitoring value (H0B57), 220V level driver is lower than 235V, 380V level driver is lower than the input voltage between phases to meet the requirements. Using a multimeter, confirm the voltage value of the main circuit (r, s, t) or the input voltage of the three-phase phase.

3. Whether the bus voltage meets the requirements. Through H0B-26, you can check whether the bus voltage value of the main circuit of the driver is consistent with the measured bus voltage; Whether the power-on bus voltage is too high or too low, and the pn voltage meets the following requirements* (1 15%) 2 * 1 10%) 2 in min pn in max v v v. 4. Just power-on, detect the speed of the defeat and feed more than 10rpm, and confirm whether there is any reverse drag or encoder feedback abnormal wiring.

When the IS620P-Sizee frame machine is wiring the Chayu bridge, it is necessary to connect the negative bus short connector of the power terminal, otherwise it will alarm NRD,