Is it necessary to disassemble the reel after the lure rod is used up?

This must be dismantled, first of all, the rod is basically installed in the rod barrel, and the wheel must be removed to fit in. Secondly, it is best to take the wheel home and clean it after each fishing. It doesn't matter if you have a one-pitch pole or a two-pitch pole, the wheels are not convenient for transport and storage on the pole.

In addition, if the wheel is not removed from the pole, it is more likely to cause damage.

You can not dismantle it, but it is not easy to maintain.

Whether you need to disassemble the reel after using the lure depends on your specific use scenario.

If you put the lure rod in a lure bucket, then the wire wheel will generally need to be removed. This is because lure rods are usually longer and the wheels are mounted on the tip of the rod, allowing the entire rod to occupy more space in the barrel. For more convenient storage and transportation, it is recommended to remove the wheels.

However, if your lure rod is packed in a rock fishing rod bag, then the need to remove the wheel depends on your personal preference and needs. Some anglers choose to remove the wheels for easier transportation and storage. But if you don't mind the wheels in the bag, it's okay not to dismantle them.

In general, whether or not you need to disassemble the reel after using the lure rod depends mainly on your specific use scenario and personal preferences.

It doesn't matter if it's dismantled or not.

If you're going to put it in a lure bucket, you're going to have to take it apart.

If you put it in a fishing rod bag, you don't have to open it.

If you want to dismantle, you can dismantle it, and if you don't want to dismantle, you can install it.

If there is no problem with your spinning wheel, it means that your unloading force is not adjusted properly, and it is OK to lock it tightly.

Spinning wheel, also known as spinning winding wheel, is the most commonly used winding wheel, which is mainly composed of wire cups, wire stops, crank handles, unloading devices, check switches, etc. Compared with other reels in use, the biggest feature of the spinning wheel is that the wire cup is fixed when the wheel is wound, and the rotation of the wire block is used to wind the fishing line on the first cup.

Precautions

Most of the high-end spinning wheels are developed and designed for lure sports, and the technology of tight parallel coiling is applied. This makes it possible to arrange the coiled thread perfectly in the wire cup without loading. Greatly avoid the problem of scrambled lines and loose cables.

The low-resistance shallow cup is mostly developed and designed for PE line, which makes it extremely easy to throw. If it is a conventional reservoir for fishing, buying high-end wheels is a huge waste and cannot be used to the fullest.

When using spinning wheels, special care should be taken to avoid scratching and abrasion on the edge of the front wire cup. Do not place on concrete floors. Once this position is ground roughly, it will greatly affect the smoothness of the toss.

You don't know this question very clearly, add me q specifically, and talk about it in detail. **There is my q

The commonly used poles of lure rods are straight handle rods and gun handle rods, and the following will talk about the corresponding wiring methods of the two poles.

1. Straight handle rod spinning wheel.

1) Go live. It is best to attach the wheels to the lure rod, then open the wire cup wire stop, turn off the check switch and start tying the knot.

Knotting method: Generally close to the top of the wire cup to tie the knot, and the figure eight ring knot is almost the same, and the remaining head can be tied with two backhand knots.

2) Stranded wire. Find a wet towel and hold the pole and thread with one hand, and shake the wheel with the other hand to start wrapping the thread until it is nine points full.

2. Spinning the wheel with the handle rod winding the thread.

1) Take-up. Put the fishing line reel on the plate, slowly shake the wheel, tighten the line, and the line to the water drop wheel outside the non-friction line cup shall prevail.

(2) Pass the main line through the rod guide ring one by one, and finally connect a lure pin by playing the figure eight ring, and then use the pin to connect the false bait to start fishing.

If you put the lure on the sea rod, you can't.

The Lure Wheel can be mounted on a sea pole. But the average fishing enthusiast doesn't put a lure on a rod. There is no specific difference between a lure wheel and a rod wheel, except that anglers choose different reels depending on the species of fish.

The spinning wheel has the characteristics of being suitable for long-distance casting, simple operation, and not easy to blow up the line, and is suitable for casting rods and long-distance fishing, floating rock fishing, etc., and the small transverse axis type droplet wheel is small in size and accurate in casting, suitable for lure fishing and raft fishing, and the large drum wheel spool is equipped with hail bearings at both ends, which has the characteristics of strong fishing power, and is more suitable for heavy fishing group boat fishing and trolling fishing. The wheels used by Lure are generally relatively small and not very large. If you really want to subdivide the lure, there are shallow cups, small fuselages and water drop wheels, and there are many lures that no one uses on the sea rod.

There are two types of fishing lines, the main line and the front line, and some anglers will cut the line when harvesting, which is relatively simple, but it is also possible to leave the line uncut.

When tying the front wire, connect it to the main line through the pin, and add a figure-eight ring in the middle, as long as the pin is removed first, the fake bait is put away, and then the main line and the fishing rod can be put away, and there is no need to cut the line.

The lure rod needs to be used with a fishing wheel, and the fish wheel and lure rod are separated, so they need to be installed before use. After use, the wheels can be removed and stored. When removing the wheel, the line needs to be cut, which can cause waste.

Therefore, it is not necessary to remove the wheel every time you reel the rod, you can tie it with a rod belt, and you can use it directly in the next fishing without installing the wheel in advance. However, if you need to store the lure rod in a special rod bag, you need to remove the wheel, otherwise you can't put it in.