Diesel pickup trucks are not easy to ignore, sometimes they are very good, sometimes they can t be h

1. Whether the steering wheel is in a state of deadlocking. The solution is simple, as long as you hit the steering wheel hard and twist the key at the same time, you can generally unlock the steering wheel lock quickly, and the ignition is an instantaneous thing.

2. Did you not return the gear to P gear when you parked? Think about it, if the D or R gear can be ignited, the jump of the vehicle at the moment of ignition is undoubtedly a huge safety hazard. Therefore, for automatic transmission vehicles (AT, CVT, AMT), manufacturers will preset this mode, and repeatedly inform in the manual:

Make sure the gear is in the P position when ignition.

3. One-button start sometimes encounters the trouble of power loss of the smart key, obviously the key is in the car, but the instrument always shows 'key matching error', this situation is likely to be the power loss of the smart key, and the start system can not sense the weak radio waves emitted by the key. Therefore, it is recommended to pick up the smart key and put it on the start button, and then press the button to start.

4. Check whether the battery has electricity. If the ignition is not ignited, it may be due to the loss of power or the expiration of the battery life due to the long-term headlights have not been turned off, and the battery is generally replaced in time according to the maintenance manual.

5. See if there is oil. If the fuel gauge shows that it is below the red line, it will not ignite. At the same time, pay attention to the quality of the oil. There have been car owners who found that there was water and mud in the fuel tank after disassembling the car, and with such oil, it is impossible for the car not to break.

6. No antifreeze is added.

Some car owners add water or inferior antifreeze to the car, resulting in a particularly cold winter, causing the entire waterway to be frozen, the engine to be frozen and cracked, resulting in the car water pump can not operate, can not catch fire, and injure other parts of the engine.

Is the engine revving enough? Please thank you for measuring the cylinder pressure.

Hello, there are many situations when you can't catch fire.

1.Check whether the battery is losing power, insufficient power or serious power loss will not be able to play, you can use a multimeter to measure the battery voltage, and there is no problem if it does not move about 12V.

2.Check that the oil pump worker is not working, you can pull out the oil pipe to see that there is no oil, and the oil is not out may be that the oil pump is broken or the fuse is burned out.

3.Check whether there is a high-voltage fire, there is no need to check whether the high-voltage bag is damaged, whether the fuse is burned out, and the bending position will also lead to no high-voltage electricity.

4.Check whether the cylinder pressure is enough, you can use the cylinder pressure gauge to measure the cylinder pressure, generally not less than 8 kg There is no big problem.

The reasons why the diesel pickup EFI car cannot catch fire: 1. The battery loss is that the starter starts to rotate but the speed is not enough, that is, it is weak, and then the starter only clicks and does not turn. In winter, the low temperature and individual electrical equipment will cause the vehicle to fail to start, especially in the winter for long-term short-distance low-speed use, the battery voltage will be lower than the rated value, starting and unable to operate normally; 2. If the flow of gasoline is blocked, do not wait for the gasoline to burn out before refueling, and there is no oil pressure in the fuel supply pipe of the engine.

This situation usually occurs in the morning when the temperature is very low, and it is caused by long-term dirt in the fuel line. When the temperature is particularly low, the water is mixed with debris, so that the fuel line is blocked, and the result is that it cannot be started; 3. The ignition system is not in good working condition, especially in cold weather, due to the low intake temperature, the fuel is not atomized well in the cylinder, if the ignition energy is insufficient, the result will be flooding, that is, too much fuel accumulates in the cylinder Zen vertical, exceeding the fire limit concentration and can not land.

What is the problem that the diesel pickup EFI car can't catch fire? First, to see if the car is out of gas, in addition, to see if the battery is out of power, and then to see if the gear is not adjusted, unlike the manual transmission model, the automatic transmission model gear is not in P or N gear, and in R or D gear, it can not be started. Reasons why the diesel pickup EFI truck can't catch fire:

1. The battery loss is that the starter starts to rotate but the speed is not enough, that is, it is weak, and then the starter only clicks and does not rotate. The low temperature in winter and the forgetting of individual electrical equipment will cause the vehicle to be unable to start, especially in the winter for long-term short-distance low-speed use, the battery voltage will be lower than the rated value, starting and unable to operate normally; 2. The flow of gasoline is blocked, do not wait for the gasoline to burn out before refueling, and there is no oil pressure in the oil supply pipe of the engine. This situation usually occurs in the morning when the temperature is very low, and is caused by long-term dirt in the fuel line.

When the temperature is particularly low, the water is mixed with debris, so that the fuel line is blocked, and the result is that it cannot be started; 3. The ignition system is not in good working condition, especially in cold weather, due to the low intake temperature, the fuel is not well fogged and infiltrated in the cylinder, and if the ignition energy is insufficient, the result will be flooded, that is, too much fuel accumulates in the cylinder, exceeding the fire limit concentration and can not be landed. @2019

The reasons why the diesel pickup truck cannot catch fire are: 1. The fuel tank has no oil or the pipeline is not passable, and the fuel pump does not deliver oil, etc., which leads to the failure to catch fire; 2. The compression force of the engine is insufficient, the cylinder liner is seriously worn, and the piston ring is carbonized; 3. The battery storage is insufficient, resulting in the inability to drive the starter to run; 4. The air intake is blocked, and the air filter is too dusty or damp. Precautions for diesel pickup trucks are:

1. You can't refuel after the diesel is consumed, because in this case, the engine will be in an idling state and inhale air, which will seriously damage the engine; 2. The diesel engine has a glow plug device, the indicator light prompts the user that the glow plug is heating, when the engine is in a cold state, turn on the ignition switch, the light is on, and the indicator light can start the engine when the lead hunger is extinguished.

1. The lower the temperature, the higher the viscosity of the oil, the lower the fluidity, and the greater the engine running resistance, resulting in the difficulty of cold starting. Solution: Park the car in a high temperature environment for a period of time to start normally, in a particularly cold place, this problem may cause difficulty in starting, timely change the oil used at low temperatures.

2. The power consumption of the battery in winter is significantly increased and the capacity is reduced at low temperature, which can easily cause the battery power to be insufficient. At this time, don't start it, if the battery is exhausted, it will be more troublesome, charge it in time.

What is the reason why the pickup truck does not catch fire when it has electricity or gas? What is the reason why the pickup truck does not catch fire when it has electricity or gas? The reason why the pickup truck cannot catch fire when it has electricity or oil may be that there is a problem with the distribution wire, such as aging of the distribution line, wrong cylinder line sequence, damage to the distributor, loose spark plug cap and other problems.

Automobile circuit troubleshooting is as follows: 1. Direct observation method: the car sometimes thinks only when it comes to black smoke, flashing sparks, abnormal sounds, heating, etc., when these conditions occur, it means that there is a problem with the circuit of the car, and these faults can be directly observed, so it can be directly judged that the fault of the vehicle is in the first place.

2. Instrument method: every car is indispensable to be equipped with a dashboard, and there will be a variety of display instruments on the dashboard, such as oil pressure gauge, ammeter, fuel gauge and so on. The role of these instruments is to monitor and monitor the spare parts of the car in a timely manner.

Therefore, when some circuits of the vehicle fail, these instruments on the dashboard will react in time to give instructions for the car troubleshooting. 3. Test light method: When there is a problem with the circuit of the car, the car can not be easily started, and any vehicle switch can not be opened at will.

The light test method is to use a light bulb to check whether the car has a short circuit fault. @2019