How to wrap the Hyundai Rena 1 4 manual combination belt

The specific operation steps for installing the manual combination belt of Beijing Hyundai Rena are as follows:

1. Unplug the headlights of Beijing Hyundai Ruina and take down the entire headlights of Beijing Hyundai Ruina, and there will be enough space to install the belt.

2. Use a wrench.

Loosen the Beijing Hyundai Rena tensioner.

3. After loosening the Beijing Hyundai Rena tensioner, you can take off the Beijing Hyundai Rena belt.

4. Install the new belt.

5. Lock the Beijing Hyundai Rena tensioner and the operation will be completed.

You should be able to see it clearly, right? If you still don't know, please ask the car master if you have a problem with the car. 4S shop professional technician, 10 minutes to solve. 】

Hello, that belt is really not easy to disturb, the belt is too long, there are too many wheels inside, it is recommended to go to the repair shop to disturb it, it is too long and it is not easy to say, [There is a problem with the car, ask the car master. 4S shop professional technician, 10 minutes to solve. 】

Hello friends, this one needs a professional engineer.

Hello, this requires professional tools, it is recommended to go to 4S to find a professional technician to operate. Have a great trip. If I can help you, please set it to, thank you!

This is the installation diagram of the belt, I hope it can help you [If you have a problem with the car, ask the car master. 4S shop professional technician, 10 minutes to solve. 】

Timing chain. The timing chain is an alloy material, which requires a certain amount of lubrication from the engine oil during use, and can be achieved in use, with a wear life of eight to 100,000 kilometers, and it also needs to be checked and replaced after reaching the service life.

In the use of the timing chain relatively loud noise, if the tensioner is broken, the noise will become louder, and even there will be a situation of jumping teeth, when there is a serious situation, replace the timing chain.

Here are the steps to replace the timing belt:

1. Disassemble the valve chamber cover, disassemble the crankshaft pulley, and remove the timing chain shell; Rotate the crankshaft, turn the crankshaft to the top dead center of a cylinder, screw the crankshaft fixing screw, and fix the crankshaft;

2. Rotate the intake and exhaust camshaft, there is a groove at the rear end of the camshaft, align the grooves of the two camshafts in a balanced manner, and snap the special tool into it;

3. Remove the old chain and replace it with a new one. The crankshaft pulley is also without a slide key, and when installed, there is a round hole on the pulley, which is aligned in the groove above the chain shell;

4. The crankshaft position sensor can be adjusted, and the gap should be adjusted in place during installation, otherwise the fault code will be reported; Both the crankshaft sprocket and the pulley rotate freely.

The old Rena is the chain, and the new Rena is the belt.

The specific operation steps for installing the manual combination belt of Beijing Hyundai Rena are as follows:

1. Unplug the headlights of Beijing Hyundai Ruina, take down the entire headlights of Beijing Hyundai Rena to the hall fiber shed, and there will be enough space to install the belt.

2. Use a wrench.

Loosen the Beijing Hyundai Rena tensioner.

3. After loosening the Beijing Hyundai Rena tensioner, you can take down the Beijing Hyundai Rena Pi Laughing Belt.

4. Install the new belt.

5. Lock the Beijing Hyundai Rena tensioner and the operation will be completed.

The specific operation steps for replacing the generator belt for Hyundai Rena automatic transmission models are as follows:

1. Loosen the fixing screws of the belt tensioner.

2. Pull the belt by hand when it becomes loose.

3. Loosen the belt from each pulley and then pull it out.

4. According to the original belt winding method, put the belt on each pulley.

5. After winding the belt, tighten the tensioner screws clockwise and install the belt.

Hello, from the crankshaft to the pump wheel, the back of the belt for the water pump, then to the air conditioning pump, to the generator, to the falling wheel, to the booster pump, to the tensioner, to the crankshaft. I don't know if I can understand this, if I don't understand, just use the wholesale analogy [If you have a problem with the car, ask the car master. 4S shop professional technician, 10 minutes to solve. 】

Compare it yourself more, and you will be [If you have a problem with the car, ask the car master.] 4S shop professional technician, 10 minutes to solve. 】

Hyundai Rena generator set.

Fitting belt assembly **?..

I suggest that you call the car repairer to help you hang up the car [If you have a problem with the car, ask the car master. 4S shop professional technician, 10 minutes to solve. 】

Summary. How to wrap the Hyundai Rena manual combination belt.

Hello, I'm helping you sort out the answers to your questions, please wait a while Hello, this first message can't be sent**, you need to send a new message. Then I'll send you **, the belt is installed.

How to change the Rena manual transmission belt?

The Hyundai Rena timing belt alignment method is the belt housing groove alignment belt slim earlier in this wheel on the round hole. Timing belts are an important part of an engine's valve system. The timing belt is connected with the crankshaft and cooperates with a certain transmission ratio to ensure the accuracy of the intake and exhaust time.

The belt is used instead of gears because the belt is quiet, has little variation and is easy to compensate. Here's how to check the timing belt:

1. Disconnect the negative cable of the battery first, and then disconnect the positive cable;

2. Disassemble the wire plug of the alternator, then remove the engine wiring harness from the cylinder head, remove the cylinder head cover, and remove the timing belt cover;

3. Turn the crankshaft pulley counterclockwise to check whether the belt has cracks or stains of organic oil and coolant, and if so, it should be completely removed. Check the belt tooth profile for wear and replace it if necessary.