In the renovation, what should I do with the masonry project?

Tile construction standards: the wall should be smooth, the brick joints should not be the same, and the mortar should be full. Home Improvement Masonry Construction Standards:

Floor tiles should consider the problem of floor drain in the balcony and bathroom, and should be sloped first, and there should be no water for no special reason in general. Masonry is the first renovation project after concealment works, and the trenches opened in the floor and walls during the construction of concealment works need to be smoothed at this stage. In particular, the trenches left by the ground and wall wiring in the hydropower project need to be filled by masons.

<> clay tile is the fired clay tile used to build a house in the past, this tile is durable after being fired by fire, and does not deform, does not worry about rust, and has good thermal insulation performance, and can effectively use the gap ventilation, the disadvantage is that it can not withstand the impact of heavy objects and rain and wind is easy to seep, if it is renovated, under the premise that the roof beam is strong, you can use color steel tile, save money and trouble, but the service life is about ten years, and you are afraid that the coal smoke will rot quickly.

Mud tiles and color steel tiles have their own advantages. In the past, the roofs of the houses in our village were all made of mud tiles, and the roofs made of mud tiles were warm in winter and cool in summer. Later, after many families rebuilt their houses, bungalows were built upstairs, and there was less place to use mud tiles.

Another advantage of mud tiles is that they are more durable.

Not easy to deform: the main raw materials of cement tile are cement and quartz powder. The shape of the formed substance is stable and the deformation coefficient is small. Sound and heat insulation, we can see the history of taste for 1,800 years.

Good with mud tiles! Regardless of the life of the clay tile, the material, and the architectural beauty, it is higher than the color steel tile. And look at the color steel tile iron sheet exposed to the acid mist salt rain, it has been rusty and falling off in a few years, and the rusty yellow dust has gone with the wind!

Cement tile is relatively troublesome, the insulation layer should be fireproof, if you want to use it for a long time, you must buy a thicker iron sheet, there is also an insulation layer in the middle, and it is more convenient to install a single-layer color steel tile. Thermal insulation layer, the top of the new buildings and bungalows is used as an insulation layer, which is warm in winter and cool in summer.

Before construction, it must be inspected, the required materials need to be prepared, and some tools also need to be prepared, and these materials must be prepared in advance to start operation, and the waterway circuit also needs to be communicated, otherwise it is easy to rework.

The trenches on the ground and walls need to be smoothed, the waterproofing of general kitchens, bathrooms and other spaces needs to be redone, the ground needs to be leveled, and finally tiles need to be paved.

In the process of decoration, it is necessary to let the mason lay a layer of cement first, and then level the ground before proceeding to the next step of decoration.

How is the masonry project constructed? Steps of masonry construction

In home decoration, masonry construction is a very important part. The construction personnel need to clean the base layer, find the slope layer, make the waterproof layer, make the insulation board, hang the tile, and deal with the details. These construction steps have clear regulations to ensure the smooth progress of the masonry construction process.

So how is the masonry project constructed? Below we will bring you the steps of masonry construction, I hope to be able to help you.

Masonry works: waterproofing layer.

The first thing the masons do is to carry out the construction of the waterproofing layer of the kitchen and bathroom. In the selection of materials for the waterproof layer, most of them choose cement mortar, and the masons are waiting for the cement slurry to be flattened when the masons are engaged in the construction. Keep the thickness above and remember to do a closed water test.

Masonry works: insulation.

The insulation layer is divided into sloping roof and flat roof, and the sloping roof should first find a flat cake when the mason is constructed, and then lay perlite, and the surface is required to be flat. After doing a good inspection, tie the steel wire mesh and the inserts. The construction plan of the flat roof is the same, but there is no need for steel wire mesh.

Masonry works: tile surfaces.

Masons must prepare enough work during tile construction, and need to carefully check the quality of the materials, whether the tiles are defective, cracked, and not good. These have a great correlation when the masons lay the tiles. After the tiles are laid, the minimum length of the upper and lower tiles is 100mm, and the cement tiles are paved with fine stone concrete.

From right to left, from bottom to top.

Masonry works: wall and floor tiles are laid.

Masons should be standardized when laying floor tiles, and polished tiles should be waxed first to prevent color changes. When laying floor tiles, the missing corners, colors, and gaps should be removed. If the flatness deviation is large, the bricks are paved with mortar, and the thickness is controlled at about 7-10mm.

The mason does not exceed the height of the wall tiles and the ground, and the floor drain should be the lowest point indoors, otherwise it has no effect. If the floor tiles have shading, if they are wrongly pasted, they should be repasted. When trimming, the whole piece should be placed in an inconspicuous place, and after the paving is pasted, it should be protected with cardboard, etc., and it is not allowed to work on it for 36 hours.

The above is how to construct the masonry project for you? The whole content of the masonry construction steps.

1. Placement of materials: In the decoration and construction of the house, there should be special requirements for the placement of materials.

2. Accumulation of experience: Before the cement slips, the brick wall should be moistened with water, which can not only promote the adhesion between the cement glaze and the surface of the brick frame, but also prevent the moisture of the cement from being sucked into the brick frame.

3. Anti-crack treatment: After the wall is anti-cracking, we can stick cool cloth strips on the gaps.

4. Clean up the excess cement in time: when tiling, the mason should use a linen cloth to wipe off the excess cement in the gaps of the tiles, and clean the tiles at the same time.

5. Masonry engineering process monitoring: tiles must be placed horizontally and vertically.

In the decoration design of the house, the mason must pay attention to the above details in the construction process, and only after paying attention to the above details, can the construction quality be ensured.

Decoration masonry projects include paving tiles, waterproof layer treatment, ground leveling treatment, smoothing hydropower construction ditch, in the construction need to pay attention to the indoor running protection measures to be strengthened, in the cement plastering to treat the wall with water wet, for the wall to carry out anti-cracking treatment, after using up the tile, to wipe off the excess cement in the gap with a rag in time, waterproof coating to do a good job.

All include waterproofing, waterway, circuit, balcony insulation, floor tile laying; Precautions include to protect the construction site, to place the materials neatly, to soak the floor tiles with water before laying the floor tiles, to clean up the excess cement on the floor in time, and to pay attention to the way of tiling when keeping the balcony warm.

Smooth the floor, tile the floor, take the stairs, take care of the walls, etc. First, you should invite a master with better skills, second, you must provide sufficient materials, third, you must put forward your own requirements, fourth, you must supervise, and fifth, consult with the other party.

Wall leveling, leveling water and electricity, ground waterproofing and ground leveling, tiling; Be sure to choose a master with good skills, put forward your own requirements, supervise the completion of the other party, negotiate the price with the other party, and provide sufficient materials.

Home decoration design is a big thing, the whole process is also by different types of workers to participate in it, love space decoration official website pointed out: in the decoration design of their own house, you must understand the precautions for mason construction.

1. Site protection.

In the decoration process, we must grasp every link in the project. From the careful indoor protection measures, we can see the quality of the construction from the details.

2. Material placement.

There are many types of decoration materials, which have specific requirements for placement, are easy to access and not easy to damage.

3. Accumulation of experience.

Before cement plastering, the brick wall is thoroughly watered, which is conducive to the adhesion of cement plastering on the surface of the brick body and prevents the moisture in the cement from being absorbed by the brick body.

4. Anti-crack treatment.

Glue strips of cool cloth to the gaps on the wall to prevent them from cracking.

It can be seen that in the construction process of masonry, it is necessary to pay attention to the corresponding details, and only after paying attention to these details can the construction quality be guaranteed.