How to embed the civil air defense fuse box and need help?

Updated on technology 2024-08-12
8 answers
  1. Anonymous users2024-02-16

    Method:

    1. Embed a junction box at both ends of the civil air defense wall.

    2. The junction box is explosion-proof and can accommodate the fuse.

    3. After the fuse is installed, it should be plugged with fireproof mud and covered with a cover plate (the cover plate is fixed by four bolts).

    4. For details, please refer to the civil air defense electrical construction method.

    There is no requirement to install a fuse on the side of the civil air defense area for the lighting line leading from the civil air defense area to the non-civil air defense area, but it must be transferred out through a closed junction box (for the method, please refer to the "Installation of Electrical Equipment in the Air Defense Basement").

    Overview:

    Low-voltage power distribution system.

    The fuse is a kind of electrical appliance that plays a role in safety protection, the fuse is widely used in power grid protection and electrical equipment protection, when the power grid or electrical equipment occurs a short circuit fault or overload, it can automatically cut off the circuit to avoid damage to electrical equipment and prevent the spread of accidents.

    The fuse is composed of an insulating base (or support), a contact, a melt, etc., the melt is the main working part of the fuse, and the melt is equivalent to a special wire connected in series in the circuit, when the circuit is short-circuited or overloaded, the current is too large, and the melt melts due to overheating, thus cutting off the circuit.

    The melt is often made in the form of filaments, grids, or sheets. The melt material has the characteristics of low relative melting point, stable characteristics and easy fuse. Generally, lead-tin alloy, silver-plated copper sheet, zinc, silver and other metals are used.

    The above content refers to Encyclopedia - Fuse Box

  2. Anonymous users2024-02-15

    Is there a fuse mounted**.

  3. Anonymous users2024-02-14

    Dear, I'm glad to answer for you: the practice of pre-embedding the civil air defense fuse A: Hello dear The practice is as follows:

    1. Embed a junction box at both ends of the civil air defense wall. 2. The junction box is explosion-proof and can accommodate the fuse. 3. After the fuse is installed, it should be plugged with fireproof mud and covered with a cover plate (the imitation plate of the cover field bench is fixed by four bolts) 4. For details, please refer to the civil air defense electrical construction atlas.

    1) The fuse box is embedded in the civil air defense, and the fuse is maintained in the distribution cabinet fuse. (2) Protective closed junction box, the thickness is not less than the galvanized steel plate welded, and the thickness of the cover plate is greater than 3mm. Song Fiber (3) Fuse:

    The lighting line leading from the civil air defense area to the non-civil air defense area is separately provided with a fuse embedded box on the inside of the protective airtight door. The fuse is commonly known as the fuse tube, the fuse is the fuse in the glass tube, which is an overcurrent protection electrical appliance, and the fuse is mainly composed of two parts of the melt and the fuse tube and the external filler. When in use, the fuse is connected in series in the protected circuit, when the current of the protected circuit exceeds the specified value, and after a certain period of time, the heat generated by the melt itself blows the melt, so that the circuit is disconnected, and plays the role of protection.

    In the commonly used fuse of the delay fuse, the fuse can be seen through the transparent glass tube in the form of a spiral, while the fuse of the ordinary fuse is similar to a thin copper wire. The fuse device of some electric vehicles does not use a fuse, but uses a (low-voltage) circuit breaker (also known as automatic switch, air switch), it is a kind of switch that will trip as long as there is a short circuit, the switch will trip when it forms a circuit, and it uses air to extinguish the arc generated during the switch. (Low voltage) circuit breakers are divided into two categories: broken assembly type and broken 10,000 type

    Break-mounted type is device-type automatic air circuit breaker; The breaker type is a universal (also known as frame) automatic air circuit breaker. The circuit breaker (low-voltage) is composed of five parts: contact installation, arc extinguishing device, tripping mechanism, transmission device and protection device. When the current exceeds the rated value for a certain period of time, the (low-voltage) circuit breaker will automatically jump (i.e. trip) to the off position, cut off the circuit, and protect the battery and motor.

    If you are satisfied with my service, please give a thumbs up, and once again wish you all the best! Peace and joy!

  4. Anonymous users2024-02-13

    Civil air defenseFusesThe installation height is.

    Installation of fuses:

    1. In order to facilitate the operation of the gliding attitude, the installation height of the civil air defense fuse should generally be between.

    2. The angle between the fuse pipe and the horizontal plane of the civil air defense fuse should be kept at an angle of 60 degrees to 75 degrees.

    3. The interphase distance of the civil air defense fuse should meet the requirements of the regulations.

    4. The upper and lower leads of the civil air defense fuse should be connected reliably and have good contact.

    5. When copper and aluminum are connected, copper-aluminum transition clamps should be used.

    Installation requirements for fuses.

    1. The porcelain should be good, the melt pipe should not have moisture absorption, expansion and bending, and the center line and fuse of the upper and lower contacts of the melt pipe.

    The axis should be in the same plane and should not be twisted.

    2. The fuse should be installed firmly and neatly arranged with special fittings, and should not be rotated left and right, and the horizontal distance between the phases should not be less than.

    The angle is generally 20°-30°.

    3. The operation of dividing and closing should be flexible and reliable, and the contact should be tight, and the upper and lower contacts should be adjusted before closing.

    4. The connection between the upper and lower leads and the switch should be firm, and the contact should be good.

    Normal conditions of use of the product: the ambient temperature is not higher than 40 degrees, not lower than -40 degrees, altitude.

    Not more than 1000m, the maximum wind speed does not exceed 35m s, and the intensity does not exceed 8 degrees.

    The product is not suitable for the following places: places with burning or danger, places with severe vibration or impact, conductive and chemical gas effects and areas with serious pollution and salt spray.

  5. Anonymous users2024-02-12

    Summary. Hello, it is divided into the following steps, 1. Embed a junction box at both ends of the civil air defense wall.

    2. The junction box is explosion-proof and can accommodate the fuse.

    3. After the fuse is installed, it should be plugged with fireproof mud and covered with a cover plate (the cover plate is fixed by four bolts).

    4. For details, please refer to the civil air defense electrical construction method.

    There is no requirement to install a fuse on the side of the civil air defense area for the lighting line leading from the civil air defense area to the non-civil air defense area, but it must be transferred out through a closed junction box (for the method, please refer to the "Installation of Electrical Equipment in the Air Defense Basement").

    How to embed the civil air defense fuse box and need help?

    Hello, it is divided into the following steps, 1. Embed a junction box at both ends of the civil air defense wall. 2. The junction box is explosion-proof and can accommodate the fuse. 3. After the installation of the reed fuse is completed, it should be plugged with fireproof mud inside, and the cover plate should be covered (the cover plate is fixed by four bolts) 4. For details, please refer to the civil air defense electrical construction method.

    The lighting line leading from the civil air defense area to the non-civil air defense area does not require the installation of a fuse on the side of the civil air defense area, but it must be transferred out through a closed junction box (please refer to the "Installation of Electrical Equipment in the Air Defense Basement" for the practice bureau).

    Is the fuse box connected to the light on the top?

    What kind of lights, lights?

    Yes, aren't they all mostly switched on and off by now?

    The box of the fuse should be connected to **.

    It should be connected in series at the live wire position before the switch.

    Just connect the switch?

    Yes, you can try, there are very few fuses to protect the lamp now, and it generally does not need to be protected by a fuse.

    This one is installed behind the civil air defense door.

    It's generally a circuit breaker or something.

    In wartime, when the lighting circuit in the basement of the civil air defense is short-circuited, the electric bell in the fuse box will ring, which can play a certain warning role. Then his monopoly is to say that this Kai has the effect of anti-corrosion, moisture-proof, high-temperature resistance, and early state calling.

  6. Anonymous users2024-02-11

    Dear, hello, I am glad to answer for you [Happy Wu Zheng] Answer: The installation height of the civil air defense closed box fuse installation is large. Installation of fuses:

    1. In order to facilitate operation, the installation height of the civil air defense fuse should generally be between. 2. The angle between the fuse pipe of the civil air defense fuse and the orange banquet on the horizontal surface should be kept at an angle of 60 degrees and 75 degrees. 3. The interphase distance of the civil air defense fuse should meet the requirements of the regulations.

    4. The upper and lower leads of the civil air defense fuse should be connected reliably and have good contact. 5. When copper and aluminum are connected, copper-aluminum transition clamps should be used. 1. Embed a junction box at both ends of the civil air defense wall.

    2. The wiring liquid box is explosion-proof and can accommodate the fuse. 3. After the fuse is installed, it should be plugged with fireproof mud and covered with a cover plate (the cover plate is fixed by four bolts).

  7. Anonymous users2024-02-10

    Summary. Hello, Method:

    1. Embed a junction box at both ends of the civil air defense wall.

    2. The junction box is explosion-proof and can accommodate the fuse.

    3. After the fuse is installed, it should be plugged with fireproof mud and covered with a cover plate (the cover plate is fixed by four bolts) 4.

    There is no requirement to install a fuse on the side of the civil air defense area for the lighting line leading from the civil air defense area to the non-civil air defense area, but it must be transferred out through a closed junction box (for the method, please refer to the "Installation of Electrical Equipment in the Air Defense Basement").

    How to embed the civil air defense fuse box and need help?

    Hello, method: 1. Embed a junction box at both ends of the civil air defense wall. 2. The junction box is explosion-proof and can accommodate the fuse.

    3. After the fuse is installed, it should be plugged with fireproof mud and covered with a cover plate (the cover car beam plate is fixed by four bolts) 4. For details, please refer to the civil air defense electrical construction method. There is no requirement to install a fuse on the side of the civil air defense area for the lighting line leading from the civil air defense area to the non-civil air defense area, but it must be transferred out through a closed junction box (for the practice, please refer to the "Installation of Electrical Equipment in the Air Defense Basement").

    Overview: The fuse in the low-voltage distribution system is a kind of electrical appliance that plays a role in safety protection, the fuse is widely used in power grid protection and electrical equipment protection, when the power grid or electrical equipment occurs a short circuit fault or overload, it can automatically cut off the circuit to avoid damage to electrical equipment and prevent the spread of accidents. The fuse is composed of an insulating base (or support), contacts, melt, etc., the melt is the main working part of the fuse, and the melt is equivalent to a special wire connected in the circuit in series, when the electric wide circuit is short-circuited or overloaded, the current is too large, and the melt melts due to overheating, thus cutting off the circuit.

    The melt is often made in the form of filaments, grids, or sheets. The melt material has the characteristics of low relative melting point, stable characteristics and easy fuse. Generally, it is made of lead ridge vertical tin alloy, silver-plated copper sheet, zinc, silver and other metals.

  8. Anonymous users2024-02-09

    Summary. Pro, pre-embedded anti-fuse box, first of all, to determine the installation location, according to the ambient temperature and humidity of the installation location to determine the installation material, generally with concrete or masonry as the foundation, after determining the foundation, fix the fuse box with screws, and then pull the copper core wire into the fuse box, pull the copper core wire into the fuse box, and then cover the fuse box, and finally connect the circuit circuit, the installation is completed.

    Pro, embedded anti-fuse box, first to determine the installation location, according to the installation location of the ambient temperature, humidity to determine the installation material, generally with concrete or masonry to do the foundation, determine the base of the Hui travel foundation, fix the fuse box with screws, and then pull the copper core into the fuse box, pull the copper stool core into the fuse box, and then cover the fuse box, and finally connect the circuit circuit, the installation is completed.

    Extended information: The embedded human anti-fuse box generally includes the following steps: 1. Anzheng installation pit:

    Holes are drilled in the embedded locations and then fixed with special inserts to secure the fuse box, while ensuring that the drain is not affected. 2. Install the inlet pipe: connect the external power harness to the inlet terminal of the civil air defense fuse box and check whether the wiring is correct.

    3. Place the civil air defense fuse box in the embedded hole: put the bracket of the civil air defense fuse box into the embedded hole and install it, and ensure that the lifting and rolling stop is completely disconnected from the external power supply, and take necessary protective measures to prevent the outside world.

    Whether to add a closed junction box to the installation of a fuse in civil air defense.

    Want. There is already a closed box for the line pipe to penetrate the anti-human wall, whether to add a closed box to the fuser?

    No need.

Related questions
3 answers2024-08-12

Fuse HRC: Current limiting fuse, also known as HRC fule, high rupturing capacity fuse. >>>More

24 answers2024-08-12

Semiconductor fuses have no polarity, so there is no positive or negative. The difference with ordinary fuses is that the fuse or fuse is made of pure silver material, which has the characteristics of fast short-circuit fusing speed, so it is also called a fast fuse, which can effectively protect semiconductor devices. >>>More

13 answers2024-08-12

When the current exceeds the specified value, the melt is blown with the heat generated by itself, and the circuit is disconnected. >>>More

22 answers2024-08-12

It is mainly to consider the relationship between the upper and lower levels, and the rated current of the upper level must be greater than the rated current of the lower level to prevent the action of skipping the level. Circuit breakers and fuses are generally not directly matched together, since there is a circuit breaker, do not use a fuse.

7 answers2024-08-12

Cut-out fuses.

It is the most commonly used short-circuit protection switch for 10kV distribution line branch lines and distribution transformers, which has the characteristics of economy, convenient operation and strong adaptability to the outdoor environment, and is widely used in 10kV distribution lines and distribution transformers on the primary side as a protection and equipment projection and switching operation. >>>More