-
Anonymous users2024-02-15For example, your gho image file is in an iso folder under the d partition Open your virtual machine and see the file in the upper left corner and click on it There will be a lot of options Here you select new (New) There are 2 sub-options Here you select virtual machine (virtual machine) Then there will be 2 options Select typical Just do it, it's as simple as that and then start selecting the file The first is to reference the image from your computer's optical drive, and the second is to store it in your place Like I said, the ISO file in the D partition is your image, so it's OK, then it's the next step to break into your virtual machine.
-
Anonymous users2024-02-14GHO's next restore tool! The virtual machine is ISO, you can select your GHO image file under the restore tool, and there is it in 360 software management!
-
Anonymous users2024-02-13Yes, you just need to change the load CD-ROM to load the ISO, and it will run after booting.
-
Anonymous users2024-02-12Only use a disc to install a virtual machine operating system to float over to give you a link, lazy people, will not go.
-
Anonymous users2024-02-11It can be said that it is troublesome to go to baidu
-
Anonymous users2024-02-101. Open the installed virtual machine directly and click [Create New Virtual Machine], as shown in the figure below.
3. Next, [Install the operating system later], and then the next step.
4. Select the Windows client operating system, and the title of the new virtual machine and the location of the storage virtual machine will pop up.
5. Select Disk as default, and finally click Done, and a new virtual machine system file will be successfully created.
6. Then load the PE image.
7. Use the built-in DiskGenius partition in the PE system to partition the hard disk of the newly created virtual machine. Once the partition is complete, shut down the virtual machine.
8. Use DiskGenius to open the virtual machine hard disk file, and open it specifically. Hard Disk - Open the virtual machine hard disk file.
9. Copy the GHO file to the D drive (i.e. the D drive).
10. Finally, load the PE mirror system again, and use the software in the PE system to restore the GHOST system.
-
Anonymous users2024-02-09Install DOS first, and then use the ghost command in DOS to restore the system.
-
Anonymous users2024-02-081. The first step is to load the ghost version of the system disk on the optical drive of the virtual machine, then start the virtual machine, enter the installation interface, and then use the partition tool PQ graphic partitioning tool here to partition the hard disk first, this step is a must. It is important to have some settings in the partition.
2. Step 2. Partition the hard disk of the virtual machine and format it. Enter the partition tool, a disk will be displayed, we right-click on this disk - select Create Split Disk, and enter the figure below.
Select the primary partition - disk type select FAT32 format - drive letter C -- C disk size, it is best to determine (here is an important point that the disk type must be selected as FAT32). After confirming, I will return to the disk interface, and a drive letter of the C drive will be displayed. There will also be a disk space left, and the extended one will be left alone.
In the same way as before. However, when selecting the partition type, select the logical disk partition, nothing else is the same. After completing these two steps, right-click and select the C drive and D drive to format and restart when completed.
3. The third step, install the GHOST version of the XP system, restart it after installation, and an error will be displayed, which is the key. Because it can't find the boot file, so at this time we need to use the installed version of the XP system disk to boot it.
4. The fourth step is to guide. Load the installed version of XP on the CD-ROM drive of the virtual machine, and then the installation screen will appear, and select the installation XP system. Enter the following interface, when you choose whether to install the system to the C drive.
You click Enter to confirm, and you will be asked to select the type of formatting. You don't have to move anything, just install the esc key, press the F3 key to exit, and the restart interface will appear, just confirm it. The point is that you have to go to the step where you choose the type of formatting.
You don't use anything as a direct esc--f3--- reboot and that's fine.
5. Finally, this interface will appear. After the fourth step is completed, there is no need to do anything, and there is no need to change the plate or anything. Just wait for the restart.
The following image will appear. How it doesn't appear, just check two of the steps. One is that in the second step, the format of FAT32 was not selected when formatting the hard drive.
One is that in the fourth step of the boot, there is no step that allows you to choose the type of format. As long as these two points are done well, there is no problem.
If you can hydroponics, wash the bulbs of hyacinths first. Then put it in a glass container filled with sun-dried water, just close to the roots, and put it in a cool place. It will take root in about a week, and the water does not need to be replaced after rooting, and a few drops of nutrient solution can be added appropriately, which is very good to raise, pay attention to observe whether the water quality has deteriorated and whether the water level has dropped. >>>More
Latex paint. I believe everyone is very familiar with it, and it will be used in home decoration. However, for different materials and different people, the effect of painting is still different, so in order to ensure the quality of brushing latex paint, construction operation is also the main part. >>>More
1.When the root system is washed first, the broken roots, rotten roots and longer roots are removed, and the roots of the orchid are soaked in potassium permanganate solution for 10 minutes to sterilize and disinfect. After detoxification, move into the prepared vase for planting, the height of the water level can not exceed one-third of the root system, too high is easy to cause root rot, when one-third of the root system adapts to the growth of the water will grow aquatic roots that adapt to growth, so that the orchid can grow normally in the water. >>>More
Chrysanthemum is a nutritious green vegetable, which is very delicious in both hot pot and stir-fry, so many farmers are now starting to grow chrysanthemum. But the quality of the cultivation is not the same, and this is because no good method is used. The following is an introduction to the planting method and time of chrysanthemum from the six points of planting time, planting method, water and fertilizer management, precautions, pest control and harvesting. >>>More
If the bathroom is leaking, you can directly do waterproofing on the surface of the tile, prepare 20 catties of tap water, and pour the waterproof fine seam agent into the bucket, and the specific operation steps are as follows: >>>More