I bought a new Hisense inverter air conditioner, and the temperature always can t drop to the set te

Hisense inverter air conditioner is a lot of functions,I don't know if yours is a dual-mode inverter air conditioner,That is, at the same time"High efficiency power saving"and"Long-term energy saving"Two inverter operation modes,If so、You can use a"Long-term energy saving"Inverter operation mode,Hisense inverter air conditioner according to the temperature you set25

degrees, the wind speed gear is adjusted automatically. Generally at 27

When the air conditioner has automatically dropped to the operation stage of low frequency and low air volume, the most accurate temperature value is the most accurate temperature number of the remote control, and if it is based on the temperature sensing value of the indoor unit, there is a deviation; Because the remote control of Hisense inverter air conditioner has an intelligent portable sense function[ifeel],It can send a signal to the indoor unit every three minutes to respond to the real-time temperature around the remote control in a timely manner[The indoor unit fails to receive the signal of the remote control for more than a certain period of time, it will be changed to the temperature sensing of the indoor unit],So when the indoor unit receives a temperature change, it will automatically adjust the operating frequency and wind speed。 Therefore, you usually need to face the transmitter head of the remote control towards the indoor unit. But you can't blow the cold air of the indoor unit directly to the remote control [so the temperature is inaccurate], you may read the manual again to understand better.

Because the temperature sensing plug is next to the air outlet, the indoor temperature sensor is on the body, and the 27-28 ° you see means that the indoor temperature has reached this, in fact, the temperature of the air outlet has reached 25 °, and because you are in the automatic mode, the wind speed automatically slows down when you see 27-28, which is normal.

Summary. 1.How many degrees do you have set on your controller?

2.How do you measure the room temperature at 27 degrees and whether the room temperature field is uniform?

3.Is the room airtight and is there any fresh air blowing in?

How can the temperature of Hisense inverter air conditioner not decrease when it reaches 27?

1.It depends on how much balance you have set on your controller? 2.How do you measure the temperature of the room at 27 degrees, and whether the temperature field of the room is evenly dismantled? 3.Is the room airtight and is there any fresh air blowing in?

Set 18

It may be that the remote control can't control the air conditioner.

The indoor unit shows that it will not be reduced until 27.

Can I turn it on with a remote control?

Yes. It's just not to give the wind, is it, or is it just showing 27 but it can cool down.

It may be that there is no confined space.

There was wind, but it didn't decrease until 27.

That is, it is not well sealed, and the wind comes in from outside.

If you close the doors and windows, it's still like this, just call ** to find after-sales service.

The set temperature usually refers to the average indoor temperature, and the temperature displayed by the machine is the temperature near the internal machine, which is a little different, which is a humanized design. The machine can be shut down when it reaches 31 degrees, indicating that the temperature control function is still normal.

High temperature air conditioning is designed for high temperature working environment, mainly used in metallurgical industry, steel mills, field work and coking industry four major vehicles, the ambient temperature below 80 cab, equipment operation room and electrical room, can make the indoor temperature control between 20 -35. The product has the characteristics of anti-vibration, anti-dust, high-temperature resistance and anti-corrosion.

Summary. Dear, the reason why the air conditioner does not heat may be because the air conditioner filter is blocked, the air conditioner refrigerant is insufficient, or the four-way valve relay or surrounding electronic parts on the main board of the air conditioner are damaged.

Four-way valve failure, usually occurs when heating, four-way valve is not good, gas or stuck, resulting in poor heating performance, in the judgment of the four-way valve can be turned off to listen to whether the suction is good, in the maintenance can be repeatedly energized to the four-way valve or gently knock on the four-way valve to reset it.

Check valve failure, check valve in the refrigeration directly on, but in the heating of the refrigerant through the auxiliary capillary, when the check valve seal is not tight or the auxiliary capillary is blocked, the heating is affected, so if the air conditioning refrigeration is normal but the heating is poor, after eliminating the problem of the four-way valve, the check valve should be checked.

What should I do if the heating temperature of Hisense air conditioner cannot be reached?

Dear, the reason why the air conditioner does not heat may be because the air conditioner filter is blocked, the air conditioner refrigerant is insufficient, or the four-way valve relay or surrounding electronic parts on the main board of the air conditioner are damaged. Four-way valve failure, usually occurs during heating, four-way valve sucking is not good, gas or stuck, resulting in poor heating performance, in the judgment of the four-way valve can be turned off to listen to whether the suction is good, in the maintenance can be reversed by the simple rise to re-energize the four-way valve or gently knock on the four-way valve to reset. Check valve failure, check valve in the refrigeration directly on, but in the heating refrigerant to pass through the auxiliary capillary, when the check valve seal is not strict or the auxiliary capillary is blocked, heating is affected, so if the air conditioning refrigeration is normal but the heating is poor, after eliminating the problem of the four-way valve, it is necessary to focus on checking the check valve.

Dear, hello, you can see if the air conditioning filter and the external unit are too dirty, choose to clean and wash the air conditioning filter, and regularly clean up the accumulation on the air conditioner except for the air conditioner. If you can't solve it yourself, it is recommended to contact professional maintenance personnel next to the cavity for maintenance.

Hello dear, I hope mine is helpful to you, and I wish you a happy life!

It is a one-to-one empty pipe machine, set at 32 degrees, and the actual temperature does not exceed 15 degrees, which is a new machine.

Dear, hello, this is a problem with the machine, you can contact the buyer for the new machine to let them check, not to ask them to give you a new one.

First click the switch button on the air conditioner to turn the air conditioner on, otherwise the air conditioner cannot be set. After that, the set temperature will be displayed on the air conditioner, click the mode alarm on the remote control of the air conditioner, and then click the display switch button immediately. It should be noted that the interval between the two button clicks should not exceed five spring fiber seconds, otherwise the operation will fail.

This is suitable for most models of liquid senmo air conditioners such as Hisense KFR-72LW E80A1.

Because the temperature sensing plug is next to the air outlet, the indoor temperature sensor is on the body, and the 27-28 ° you see means that the indoor temperature has reached this, in fact, the temperature of the air outlet has reached 25 °, and because you are in the automatic mode, the wind speed automatically slows down when you see 27-28, which is normal.

The automatic air of the inverter air conditioner does not reach the set temperature, which is normal. Because:

1. The external ambient temperature causes no way to continue to reach the set temperature, and the temperature of the external unit can be changed to reach the set temperature.

2. The air conditioner's own capacity has reached the limit, and there is no way to reach the set temperature, and the current temperature is the maximum limit of the air conditioner.

3. Reduced heating capacity under low temperature conditions: when the set temperature is not reached and the outlet air temperature is reduced to a certain extent, the cold air function will work and the defrosting function will work. It shows that within the capacity of the machine and under specific use conditions, 18 degrees is the limit.

Dear Hisense users, hello!

The quality of air conditioning and refrigeration depends on the temperature difference between the air inlet and the air outlet, and the national standard is a temperature difference of 8 degrees! air inlet (do not turn on the air conditioner temperature); The air outlet (the thermometer is placed on the swing blades of the air conditioner), the greater the temperature contrast temperature difference detected, the better the effect, the minimum should not be lower than 10 degrees, otherwise the air conditioner will have "anti-freezing protection". Need help dialing Hisense Kelon air conditioner national unified 24-hour service**!

During the warranty period, we provide free door-to-door service.