How do you drain the water in the laundry when moving? There is water in the washing machine when mo

Updated on home 2024-08-15
35 answers
  1. Anonymous users2024-02-16

    Hello, if you want to drain the water of the washing machine when moving, you should put the washing machine in a higher position, and then. Lower the drain pipe, the washing machine can be slightly tilted, and try to drain the water as much as possible.

  2. Anonymous users2024-02-15

    There is a small valve under the washing machine, which only needs to be opened with a screwdriver to remove the moisture inside, and when moving, keep the washing machine as much as possible not upside down, and be careful when transporting it slightly, which is very convenient.

  3. Anonymous users2024-02-14

    If you want to drain the water in the washing machine when moving, you need to move the washing machine near the floor drain and unplug the drain pipe of the washing machine to drain the water stored in the washing machine.

  4. Anonymous users2024-02-13

    The front-loading washing machine can be set to have a single drain, so that all the water in the washing machine can be drained.

    If it is a washing machine, you can directly put the drain pipe flat and raise the washing machine to drain the water inside.

  5. Anonymous users2024-02-12

    Put the pipe of the washing machine to discharge the water into the lowest, your lowest position can better allow you to put the rest of the water clean, put the pipe at the lowest, plug in the power supply, and modulate it according to the switch on the washing machine, modulate to the position of the water discharge, the position of dehydration, so that the dehydration can be discharged in about a minute.

  6. Anonymous users2024-02-11

    Remove the drain pipe from the snap on the back of the machine, and it is best to start the single dewatering program, as the drum washing machine itself does not have a drain valve, and the water remaining in the bucket will be drained by gravity. Alternatively, when the dewatering process is activated, the water droplets remaining on the drum wall will have an air-drying effect through the air generated by high-speed rotation, and the dropped water can also be discharged naturally.

  7. Anonymous users2024-02-10

    If it is a fully automatic washing machine, first power off it and then open the back cover, you can find that there is a solenoid valve in the lower part and a column shaft in the middle, push it hard in the direction of the solenoid valve, you can open the drain valve, and let go after the water is discharged; If it is a semi-automatic washing machine, open the back cover after the power is off, and see a tractor underneath, which is composed of steel wire and spring, and the water will be released when you pull it hard with your hand.

  8. Anonymous users2024-02-09

    If you want to drain the washing machine before moving, you have to drain all the water in the washing machine. Then dry him and then wrap him. In this way, it is easier to move, this drainage is very simple, and it can be discharged directly with a drainage pipe.

  9. Anonymous users2024-02-08

    Hello; 1. Select a single rinse program.

    Generally, the first thing to perform is drainage and dehydration, so when the single rinse program is opened, there is an interval between the emptying of water and the start of the dehydration program.

    2. Select a single dehydration gear.

    5 general single dehydration, the first execution is drainage, so, open the single dehydration program, between the emptying of water and the start of the dehydration program, there is an interval time, master this node, stop the operation of the machine, even if you just start dehydration, you can also take this method, at this time the speed is very low, stop the machine is not much harm.

    Hope it helps.

  10. Anonymous users2024-02-07

    You can use a towel and an absorbent sponge to suck the water out, or open it yourself with a screw from the back, then take out the bucket and turn it upside down for a while to clean the water in the pipe.

  11. Anonymous users2024-02-06

    Washing machine drain method: Turn off the inlet faucet. Turn off the power to the washing machine.

    Use your finger to open the lower cover. Remove the drain plug and let the water out. Turn the drain pump filter to the left until it is turned on and a lot of water will come out.

    Remove impurities from the drain pump filter, clean it and then put it back in. Close the upper and lower lids.

  12. Anonymous users2024-02-05

    If there is water in the washing machine, you can raise the washing machine higher, and then place the drain pipe lower than the washing machine, so that the water in the washing machine can be drained by the effect of liquid pressure.

  13. Anonymous users2024-02-04

    To drain the water from the washing machine, we only need to raise the washing machine by 5 cm. Then tilt it in the direction of the drain pipe, and the water will be completely drained in about 5 minutes.

    When moving, be sure to pay attention to the alignment, do not tilt or tilt on the side.

  14. Anonymous users2024-02-03

    If there is excess water in the washing machine when moving, then pull the washing machine higher! Lift it up so that the washing machine is in a suspended state, put the drain pipe into the bathroom floor drain for two or three minutes, and all the excess water will be controlled!

  15. Anonymous users2024-02-02

    One is to plug in the power plug and rotate the drain button to let it drain. The second is to open the washing machine, find the drain valve, and drain the water by rotating the drain valve. Both can be used.

  16. Anonymous users2024-02-01

    This means that if you want to drain the water in the washing machine, then you put the drain behind it on the ground, because the drain pipe doesn't say that it goes around at high speed. If you take the top one off and put it directly underground, the water inside will be drained cleanly.

  17. Anonymous users2024-01-31

    When moving, drain the water in the washing machine in advance, turn on the drain switch, and let the drain pipe lay as flat as possible, so that after the stagnant water is placed, do not cover the lid, and let him air dry the remaining water naturally.

  18. Anonymous users2024-01-30

    The water in the washing machine can choose the drain button, and then it can be discharged directly from the drain pipe, and the button description of the washing machine will say the word drain, which is a very simple operation.

  19. Anonymous users2024-01-29

    If you want to drain the water in the washing machine, then you can use a screwdriver to gently unscrew the water in the back of the washing machine, and after opening it, he will drain all the water.

  20. Anonymous users2024-01-28

    If the washing machine is installed correctly, it can drain the water as long as the single dehydration function is activated, and if it is not installed correctly, then the dehydration function should be run again according to the correct installation method.

  21. Anonymous users2024-01-27

    When moving, the water in the washing machine is not clean, you can turn on the self-cleaning function of the washing machine, and it will clean up the water by itself.

  22. Anonymous users2024-01-26

    Dear, your washing machine is a drum washing machine or a wave wheel washing machine, the drum washing machine is a strong drainage, every time it is used up, it will automatically shoot the water, and the wave wheel washing machine will directly wash the clothes and drain the drain, and move the washing machine directly away.

  23. Anonymous users2024-01-25

    General washing machine, after washing, the water of the washing machine is basically drained, but there is a small amount of water that cannot be drained clean, as long as you unload, put on and off the water, and let the remaining water flow naturally, you can!

  24. Anonymous users2024-01-24

    A small valve under the washing machine, only the screwdriver opens to remove the moisture inside. Try not to turn the washing machine upside down, and be careful to carry it, very.

  25. Anonymous users2024-01-23

    What do you mean to put the water out of the washing machine when you move, and when you run out of the washing machine, don't they have a sewer pipe there? If you don't have a sewer pipe, you can connect a long pipe, or put it directly in the piggyback, and put it in a bucket to let this water out.

  26. Anonymous users2024-01-22

    If you want to move, I think the best way to get rid of the water in the washing machine is to get up after using the washing machine, and then move the washing machine to measure the water in it.

  27. Anonymous users2024-01-21

    The water in the pipes can be completely drained. This is normal. Each washing into or part (sampling.

  28. Anonymous users2024-01-20

    If you have a boat, the water in the washing machine, as long as you open the drain below and manually drain it, you can do it.

  29. Anonymous users2024-01-19

    It is common for the washing machine to have residual water inside the washing machine when it is moved, and it is necessary to take measures to completely drain the water inside the washing machine, otherwise it may cause water leakage and damage to parts. The specific steps are as follows:

    1.Disconnect the power to the washing machine and make sure the washing machine is powered off. This is the most basic security measure.

    2.Open the washing machine door so that the water inside can easily flow out. If there is clothing, remove it so that the water can flow smoothly.

    3.Tilt the washing machine so that water can flow out of the drain or door slot. The front and back sides of the washing machine or the left and right sides can be slightly tilted, with an inclination angle of about 5-15 degrees, so that the water flows out in the direction of natural inclination. Place a basin or other container under the drain to collect water.

    4.Use a vacuum aspirator to suck up excess water. If the tilt does not drain the water, you can use a household vacuum to suck the water out of the washing machine. Insert the suction connector into the drain to absorb water.

    5.Use a press to drain water. For high-end front-loading washing machines, the water can be drained with the help of the washing machine's drain pump.

    Connect the drain pipe to the faucet or other connector, then open the water inlet valve, start the drainage program that comes with the washing machine, and use water pressure to drain the internal water. Before doing this, make sure that the drain line is clear.

    6.Remove the laundry and wipe the inside of the machine with a towel. If the above steps still do not drain the water completely, you need to open the door cover of the washing machine, remove all the clothes, and then wipe the excess water in the inner shell, sealing ring and door groove of the washing machine with a dry towel or rot and burn.

    7.Relocate and reconnect before use. After moving the washing machine to the new address, reconnect it to the water power supply and check that it is working properly. When you run it for the first time, you still need to pay attention to whether the waterway or joint is cold and leaking!

  30. Anonymous users2024-01-18

    If it is a washing machine with a wave wheel sleeve, after placing the straight drain pipe, turn on the single dewatering program, so that the machine can open the water discharge valve.

    If it's a front-loading washing machine, just pull the drain out of the checkpoint and place it straight against the floor.

  31. Anonymous users2024-01-17

    When moving, in order to ensure the safe transportation of the washing machine, it is necessary to drain the water inside the washing machine. Here are some suggestions and methods:

    1. Set the washing machine to drainage mode: Set the program dial or touch screen of the washing machine to drainage mode, and then start the washing machine to drain water automatically. During drainage, make sure the drain pipe is connected to avoid water splashing.

    2. Manual drainage: If the washing machine can't drain automatically, you can try to drain it manually. Lower the drain pipe to the ground level and allow the water to flow out naturally. If needed, a drain can be inserted into a container so that the moisture can be collected.

    3. Use a sponge or towel to absorb water: If the above socks cannot drain the water, you can use a sponge or towel to absorb the residual water in the washing machine. Open the washing machine door, place the sponge or towel in the washing machine, absorb the moisture, and wring the sponge or towel out.

    4. Check the filter screen: Some washing machines are equipped with a filter screen at the bottom, which can be disassembled for cleaning. Before moving, check the filter for moisture, and if so, remove the filter and pour it out.

    During the moving process, in order to avoid damage to the old manuscript washing machine, it is recommended to leave the washing machine door slightly open for ventilation. At the same time, make sure that the washing machine is placed stably during transportation and avoid shaking violently. If needed, seek a professional moving service for removal.

  32. Anonymous users2024-01-16

    When you move, you find that there is water in the washing machine, you can turn on the power of the washing machine, and then after infiltrating Hongpei, you can drain the water in the washing machine by only activating the normal drying function.

  33. Anonymous users2024-01-15

    You can try to drain the water in the washing machine as much as possible by following the following methods:

    Drum washing machine.

    Detach the drain from the snap on the back of the machine and lay the drain flat, preferably with a single dewatering procedure. Since the drum washing machine itself does not have a drain valve, the water remaining in the bucket will be discharged by gravity.

    When the dewatering process is activated, the water particles remaining on the drum wall are dried by the air generated by the high-speed rotation, and the dropped water flows out naturally.

    Finally, open the glass door and let it air dry for a while, and you're good to go.

    Sleeve washing machine.

    Lay the drain pipe flat, and the single dewatering procedure must be turned on to allow the drain valve to open so that the water inside can be emptied.

    The inner drum that rotates at high speed is also the same principle as the drum washing machine, and will be air-dried.

    Then, open the top cover and let it dry for a while so that the inner cylinder is drier.

  34. Anonymous users2024-01-14

    Just leave the lid of the washing machine open and let it dry for a few days.

  35. Anonymous users2024-01-13

    Summary. Look at whether your washing machine is fully automatic or semi-automatic, if it is a fully automatic washing machine, first power off it and then open the back cover, you can find that there is a solenoid valve in the lower part and a column shaft in the middle, push it hard in the direction of the solenoid valve, you can open the drain valve, and let go after the water is discharged; As.

    If it is a semi-automatic washing machine, after the power is off, open the back cover, and see a tractor below, composed of steel wire and spring, pull it hard with your hand, and the water will be.

    It's out. I hope I can help you, thank you, I wish you a happy life, dear.

    There is water in the washing machine when moving, how to drain the water

    Hello: I am very happy to serve you, see whether your washing machine is fully automatic or semi-automatic, if it is a fully automatic washing machine, first power off it and then open the back cover, you can find that there is a solenoid valve in the middle of the lower part of the column shaft, push hard in the direction of the solenoid valve, you can open the drain valve, and let go after the water is discharged; As.

    If it is a semi-automatic washing machine, after the power is off, open the back cover, and see a tractor below, composed of steel wire and spring, pull it hard with your hand, and the water will be.

    It's out. Hope mine can help you.

    There is water in the washing machine when moving, how to drain the water

    Look at whether your washing machine is fully automatic or semi-automatic, if it is a fully automatic washing machine, first power off it and then open the back cover, you can find that there is a solenoid valve in the lower part and a column shaft in the middle, push it hard in the direction of the solenoid valve, you can open the drain valve, and let go after the water is discharged; If it is a semi-automatic washing machine, open the back cover after the power is off, and see a tractor underneath, which is composed of steel wire and spring, and the water will be released when you pull it hard with your hand. I hope I can help youThank you for wishing you a happy life Pro-Questioner Consultation Record There is water in the washing machine when moving, how to drain the water Hello: I am very happy to serve you, see whether your washing machine is fully automatic or semi-automatic, if it is a fully automatic washing machine, first power off it and then open the back cover, you can find that there is a solenoid valve in the middle of the buried envy part, and there is a column shaft in the middle, push it in the direction of the solenoid valve, you can open the drain valve, and let go after the water is discharged; If it is a semi-automatic washing machine, open the back cover after the power is off, and see a tractor underneath, which is composed of steel wire and spring, and the water will be released when you pull it hard with your hand.

    Hopefully mine can help bend and take a picture of you.

    Electromagnetism is in **, what does it look like.

    Pull it still doesn't come out of the water.

    If the drain valve is pulled and the water does not come out, it means that there is a problem with the drain valve and it needs to be replaced.

Related questions
8 answers2024-08-15

I. Preface Throughout the life of modern people, there will always be several changes and changes. Most Chinese people believe that relocation (moving) will bring different degrees of good luck and more or less good luck to the person concerned (or the owner and his family), so most people will always choose an auspicious day of the zodiac, choose an auspicious time, and follow the relevant traditional customs and joys and taboos when moving (moving), hoping to have an auspicious omen, and only then can they feel at ease. >>>More

16 answers2024-08-15

It is not possible to get the ants to move on their own. Because ants sense the dampness around them, they will move on their own. So, I suggest that you watch the ants move when it's about to rain!

6 answers2024-08-15

1. If the washing machine cannot be turned off, the main reason is that the channel at the drain switch is blocked by the fabric fibers left over from long-term laundry, and some are blocked by foreign objects (such as socks) inside. You can remove the drain pipe, clean the drain switch with a clip, make sure the passage at the switch is clear, and then install the drain pipe and you're done. 2. If the switch is turned off or drained, 1. There are foreign objects or dirt stuck on the sealing mouth at the closing port, 2. The closing spring is damaged. >>>More

5 answers2024-08-15

1. Disassembly and assembly method of modular furniture:

Furniture disassembly only needs to disassemble the hardware assembly on the furniture, and not all the hardware on the furniture. In the process of dismantling furniture, you must remember the position of the furniture so that you will not make a mistake when installing it, if you are afraid that you will forget to mark the furniture (1 day ago). >>>More

5 answers2024-08-15

July 2012 awaits you on an auspicious day of the zodiac

You need to avoid the opposition sun, the five elements [Golden Day] that are unfavorable to your husband's zodiac [Xinyou Wood Chicken], and the evil day when the entrance door is facing [Junzhi]. >>>More