What s going on with the natural gas showing that it doesn t burn?

The gas meter shows that there is still a lot of gas, but it is not lit. There could be the following reasons:

1.Regardless of your gas meter.

Whether the battery is charged or not. Probably a gas meter.

The power is out, and the solenoid valve in the meter is closed.

2.The gas meter is broken.

3.The gas pipe is clogged.

4.The voltage regulator is turned off.

Card meter overcurrent protection (I don't know if the gas meter you are looking at is right.) Nowadays, the general gas meter is a smart meter with a card. The mechanical degree above them is the amount of natural gas used, not the remainder.

For the residual gas flow, you need to press the button on the meter for the remaining gas volume to be displayed on the screen).

6.Ask the natural gas company personnel to come to the site for repairs. If there is no **, it can generally be seen on the pressure regulating box of the building in the community. (2017-11-03, chaos and chaos).

Troubleshooting steps:

1.Observe whether the spark of the gas stove is soft and weak, and whether the discharge frequency is significantly slower than before. If this is the case, our battery is low, and replacing it with a new one will solve the problem.

2.If the spark sounds crisp and powerful, but it just doesn't ignite, then consider whether the air path is unblocked. It is likely that the nozzle inside the burner is clogged during use. Remove the flame splitter cover, pass a thin wire through the nozzle hole, and then put it back into the flame splitter cover to re-ignite.

3.Check whether the throttle of the gas stove valve body is adjusted too much, resulting in excessive airflow in the fire hole and impacting the electric spark. You can adjust the damper left and right to test whether the test fire is normal.

You've just opened a pipeline of natural gas. This is because there is air in the pipe, you can open the valve for a while, close the valve when you smell of natural gas, and then light it again. Generally, the air that has just been ventilated will not be too easy to use for a few days, and sometimes the fire will be extinguished halfway, so you should be very careful when using it, and wait for a few days to exhaust the air in the pipe.

If the gas source of natural gas is not opened, first check whether the valve is opened, if it is not opened, just open it and then test the fire.

2.If the natural gas stove battery has no electricity, it will not ignite, just replace it with a new battery. 3.The gas pipeline is blocked, so it can't catch fire, as long as the pipeline is dredged.

The reason why there is gas in the home is not ignited: low battery, faulty ignition needle, clogged fire cover, blocked pipes.

1. The battery is insufficient

If the battery is insufficient, even if the natural gas is gased, it will still cause the natural gas stove to fail to ignite. At this point, the battery should be replaced with a new one.

2. Ignition needle failure

If the natural gas stove is to be successfully ignited, the distance between the ignition needle and the fire cover should be kept between four centimeters and six centimeters, and the angle between the two must be kept at 90 degrees. At this point, the ignition needle should be moved back to its proper position.

Note that the ignition needle is relatively brittle, and it is recommended that you do not use tools to move it, but should move it by hand to avoid damage to the ignition needle.

3. The fire cover is blocked

If the natural gas stove is to be successfully ignited, then the gas outlet holes on the fire cover must be kept unobstructed, if these gas outlet holes are blocked by foreign objects, it will lead to the natural gas outlet is not smooth, so that the natural gas stove can not ignite. At this point, the blocked air outlet hole should be unblocked.

4. Pipeline blockage

If the natural gas stove is to be successfully ignited, the connecting hose between the natural gas stove and the gas pipeline must be kept unobstructed, and if there is a blockage in the connecting hose, it will also cause the natural gas stove to fail to ignite. At this time, the gas pipeline should be unblocked, or it should be replaced with a new one.

The reason why the gas at home is not in arrears may be because the gas valve is not opened, first make sure that the valve is open, and then check whether the pipeline is connected normally, if the pipeline connection is normal, consider other reasons. Generally, when the gas pipeline is connected normally, there are the following reasons for the failure to ignite.

1. The battery is misplaced, and the battery in the natural gas stove will be misaligned, and the contact will be poor. The solution is to reinstall the battery and then light it.

2. The battery is out of power, the solution, check the battery condition, replace the battery and then re-ignite.

3. There is dust, and the dust in the gas stove will block the pipe, resulting in no fire, the solution is to clean the dust with a brush.

4. When the stove enters the water and the pot is cleaned, the water may splash into the gas stove, and after the water enters, the gas stove will not catch fire. The solution, wipe the water clean with a dry rag, let it dry for a while, and then you can start the fire.

4. Check whether the circuit has poor contact, mainly to check whether the positive and negative poles of the battery box are rusty, and if there is poor contact with the circuit, it will cause no ignition.

5. Check the overpressure protection, that is, the pressure reducing valve, many gas stoves have overpressure protection function, and the overpressure cannot be opened. 6.Check whether the pipeline is blocked, once the pipe is blocked, it will cause a fire and other situations, I hope it can help you.

Natural gas shows gas but can't hit the fire pro, hello! 1. Check whether the pressure of the gas beam branch stove is sufficient, if the pressure is insufficient, it will cause the gas and natural gas stove to be burned in time. Check whether the gas pipeline of the gas stove is blocked, which will cause insufficient pressure and cannot be used to supply the gas to the gas stove in time.

2. Check whether the position of the ignition needle of the natural gas stove is offset, if the position of the ignition needle is offset, the gas stove is still not ignited in the case of electricity and gas. It is necessary to move the position of the ignition rubber brigade fire needle to be in a perpendicular direction to the position of the gas outlet hole of the gas stove, so as to ensure the normal ignition of the natural gas stove. 3. Check the weak current, you need to adjust the damper under the gas stove to make the fire bigger, so that the thermocouple can eat the flame and accept the heat to transfer heat.

When this happens, a thermocouple needs to be replaced. 4. If the above problems are ruled out, and the gas stove still does not ignite the fire, you need to check whether the connection line between the ignition needle and the solenoid valve is broken, and whether the nozzle of the damper regulator is blocked, and find professional personnel to check these two parts. Hope it helps!

1. Because of the low water pressure, the gas channel is not automatically opened; 2. If there is no ignition sound, check whether the battery used for ignition is charged; 3. Other reasons are that the gas may be out of gas, resulting in no fire. Suggested treatment methods: 1. Test the natural gas water heater, and find that it is the reason why the ignition is not ignited, you can check the water pressure first, if the water pressure is less than 2kg, you need to pressurize it.

You can also wait 1 minute at home before trying, especially in winter, when the water pressure is too low and you can't catch fire, you need to continue to ignite. Try to switch the faucet more often, and it will generally be good soon. 2. If you continue to ignite, but there is still no sound of fire, it is because the ignition battery is out of power, remove the original battery, check what number of batteries it is, go directly to the supermarket to buy 2 new batteries, and replace the new batteries to use normally.

3. It is also possible that the gas of natural gas is insufficient. If it is pipelined, check whether other gas appliances in the home can still be used normally, if not, replace it with new gas, or charge money.