How should the purchased stone slabs be transported?

Updated on society 2024-08-06
6 answers
  1. Anonymous users2024-02-15

    If it's a finished board:

    To be packed by export.

    It is more convenient to use a truck, but each box should not be stacked on top of each other, and it is better to put one layer.

    The thickness of the wooden box planks should be 2 cm. The inner low layer of the wooden box should be placed with plywood, and the foam should be about 1 cm to 2 cm above the plywood, and the waterproof film and very thin foam should be placed on the foam and around it. You can put the board, "The first and last pieces can be put 1 cm of foam, which is more safe.

    Put the board vertically, the light side should be glossy, and two thin foam strips should be placed between the glossy surfaces, about 6---10 cm wide and 40 to 50 cm wide, and clamped from the top left and right 1 3 places. After it is full, cover it with a thin foam and waterproof membrane, and then use the packing strip to the board to block the waist and pack "two, >, and then cover the lid and nail it, and the outside is also to pack two pieces at the waist, and there is one or two around the belt. That's it.

    If it is packaged in this way, it is very safe, and we send it abroad, through the car, then by ship, and then by car, and then by car, there is no problem

    If it is a large board, it should be tied to the car in the direction of the car, and the packing place should be covered with foam, rubber and the like.

  2. Anonymous users2024-02-14

    The stone can be transported directly, pay attention to it and put it upright. Do not lay flat. If it is a long-distance transportation, you can consider making a frame with waste wood first.

  3. Anonymous users2024-02-13

    Be sure to hit the wooden box.

    Beat it with a rigid belt.

    Also, it is necessary to wrap it in waterproof paper.

  4. Anonymous users2024-02-12

    There are many things that should be paid attention to, and the manufacturer will explain it to you when you buy it.

  5. Anonymous users2024-02-11

    Decorative stone has strict requirements for packaging technology, and the packaging is not appropriate, resulting in damage to the edges and corners, and the heavy ones may break. Improper transportation and storage. Increased the number of scrap and defective products.

    Therefore, in order to get the ideal decorative effect, it is necessary to work on packaging, transportation and storage.

    a) Stone packaging.

    The packaging of stone plates should be decided according to factors such as quantity and transportation conditions. There are no more than the following two types of packaging:

    1 Packed in wooden case.

    For long-distance transportation, this method is generally used. Contrast the smooth side of the sheet against each other. The order is placed vertically in a box lined with moisture-proof paper, or 2 or 4 pieces are tied with straw rope in the box, and the space in the box must be plugged with elastic soft material.

    The wooden box shall not be used with other external materials, and the thickness of the wooden sedan chair shall not be less than 20mm. Iron waist hoops should be added at both ends of each box, and iron clad corners should be added to the rung sails.

    2 Straw rope packing.

    There are two situations for straw rope packaging: one is to wrap the smooth opposite plate with a straw rope with a diameter of not less than l0mm along the length and width in order. Do not expose the product and tie it firmly. Another kind of packaging is to bundle the smooth opposite plates with a straw rope with a diameter of not less than 10mm in the shape of a "well", and each binding point should not be less than 3.

    The strip products are bundled in the direction of width and thickness, and 2-4 points are bundled according to the length of the product, and there are no less than 5 straw ropes at each point. After the plate is packaged, there should be a mark such as the number or name, specification and quantity of the plate. The materials used in the supporting project should be numbered according to the drawings on each plate.

    The packaging box and packing rope must have "upward", "moisture-proof", "careful" indication signs, and its symbols and use of socks should comply with the provisions of GBL91-73 "Packaging, Storage and Transportation Indication Signs".

    b) Transportation of decorative stone plates.

    Handling and handling must comply with the following regulations:

    1) When handling, it should be handled lightly, it is strictly forbidden to fall and roll, and the back edge must land on the ground first when stacking upright.

    2) When the area of a single stone plate exceeds that of a single piece, it will be handled upright. When large products are handled with lifting tools, their stressed edges must be padded.

    3) When the products packed in wooden boxes are loaded and unloaded with lifting equipment, it is advisable to use one box for each lifting. When handling the products packaged with straw ropes, the straw ropes shall not be lifted.

    4) Loading and stacking should be carried out in accordance with the requirements of storage, and the transportation is required to be stable, and collisions are strictly prohibited.

    c) Storage of stone plates.

    Stone slabs should be stored indoors and must be covered for outdoor storage. When the plate is stacked upright, the smooth surface should be relative, its inclination should not be greater than 15 °, the stack height is appropriate, and the bottom surface and the layer must be supported with non-polluting elastic materials. When it cannot be stacked upright, the smooth surface should be opposite, the ground should be flat and solid, the interlayer support point should be on the same vertical line, and the stack height should be 1m.

    After packaging, the stacking height should be 2m.

  6. Anonymous users2024-02-10

    When transporting stone slabs, they should stand up and lean against the fixed side of the carriage.

Related questions
8 answers2024-08-06

It seems that this is a newbie, so I suggest you go **.

Classified by use: (1) Bridge steel plate (2) boiler steel plate (3) shipbuilding steel plate (4) armor steel plate (5) automobile steel plate (6) roofing steel plate (7) structural steel plate (8) electrical steel plate (silicon steel sheet. >>>More

13 answers2024-08-06

Solid wood multi-layer board, solid wood multi-layer board is mainly made of three layers or more of one millimeter solid wood veneer or thin board by glue hot pressing, the material of the core of the board is mainly poplar, miscellaneous wood and amine wood, etc., it has high strength and good stability. Solid wood multi-layer board has a large glue content, and it is necessary to do a good job of edge sealing treatment during construction to reduce pollution. >>>More

12 answers2024-08-06

Stone polishing machine - introduction to the working principle of stone polishing machine >>>More

29 answers2024-08-06

When buying cosmetics, female college students should choose a cosmetics that is more suitable for them, in fact, the ** of cosmetics is not particularly important. If a cosmetic product is expensive, but it is not suitable for us, it is useless for us to buy it. But if we can buy a cosmetic product that we like and suit us for a small amount of money, it is more useful. >>>More

8 answers2024-08-06

First of all, many of your lifestyle habits will have to change once you enter college. Everyone has their own habits. You can't influence others because of your personal work and rest time. >>>More