How to use the water heater correctly What is the correct way to use the electric water heater

1.The electric water heater just got back and can't be used right away. It should be installed in a suitable location in the bathroom first, and then debugged to see if the electric water heater will run abnormally.

Once you are sure that the water heater is functioning properly, you can use it for your family. 2.In order to effectively avoid electric shock, the socket of the electric water heater should be provided with a reliable grounding wire, and the household power supply system should be installed with a leakage protection device.

Since the power of the electric water heater will be relatively large, the electric water heater must use 4 flat wires and three-pin sockets. 3.When using an electric water heater, you also need to pay attention to the type of electric water heater.

If the electric water heater is a storage type electric water heater, you need to fill the electric water heater with water before starting to heat. Once heated, you can use an electric water heater. 4.

If the electric water heater is an instantaneous electric water heater, there is no need to add water first. Turn on the power of the electric water heater directly, and then turn on the faucet, and the hot water can be released. Instantaneous electric water heaters generally need to wait about five seconds for heating, and the temperature of the water flowing out is generally in a moderate state.

1. When using the electric water heater, turn on the power supply, the indicator light is on, indicating that the electric heating is on, when the water temperature reaches the set value, the indicator light is off, indicating that the power is cut off. The indicator light turns on and off, indicating that it is automatically holding warm.

2. The electric water heater (storage type) should be filled with water first, and then heated by electricity, and can be used after preheating. If the pressure of the water source drops or the water stops suddenly, it is best to turn off the power.

3. Electric water heaters are equipped with faucets and with reflux installation, usually "blue" for cold water and "red" for hot water. If the water temperature is too high, you can turn on the "blue" faucet at the same time and adjust the amount of water to enjoy the hot water at the right temperature.

4. There is a water temperature mark scale on the temperature conditioner of the electric water heater, such as "i", or marked with English and Arabic numerals to indicate the low, medium and high conditioning position of the water temperature, and the temperature adjustment knob is aimed at a certain mark, and the water temperature of the water heater will reach the temperature set by the indication in the file. When using, let the water spill out first to try out the actual water temperature to avoid the water temperature being too high and scalding**.

5. When filling the water, it is necessary to open the water outlet and check whether the water can be filled after the air in the inner tank is completely discharged.

6. The power supply must be cut off after discharge.

7. When used as a blockade device, the water inlet valve must be open during heating.

8. When the valve is just opened, do not put the direction of the water towards the human body.

1. Plug in the power supply, press the switch button of the electric water heater, and set the water temperature at the same time. In winter, the temperature can be turned up a little higher.

2. After the water boils, first adjust the valve to the middle position, put the water, and try that the water temperature is not cool before starting to use. (Generally, the left side of the valve marked with the word H is hot water, and the right side marked with C is cold water.) Hot water is marked in red, and cold water is shown in blue. )

3. After the water temperature is constant, it can be used, because the electric water heater is surrounded by water, which is easy to be electrocuted, so try not to touch other places with your hands or other parts during use, especially around the power supply.

4. When using the electric water heater, when the water valve is opened and there is no water, the power supply should be disconnected immediately to prevent the electric water heater from being damaged due to failure when working without flowing water.

5. If the water pressure or voltage is too low, the use should be suspended.

6. After use, turn off the switch on the electric water heater first, wait for your hands to dry, and then unplug the power.

Most of the bathroom walls are pre-embedded with power cords, water pipes, etc., when the location and depth are unknown, it is necessary to use professional instruments to detect and locate in advance to determine the installation position; In addition to the tight connection of pipelines, the connection of inlet pipes, outlet pipes, valves, and water conversion valves of electric water heaters, it is also necessary to consider the insulation of hot water, the length of the pipeline and the routing path, the neatness of the appearance, and the grounding of the water pipe. The installation position should be able to give full play to the performance of the electric heater and facilitate future maintenance, maintenance and repair. When using a storage type electric water heater, the hot water valve of the hot and cold water regulating valve should be opened first, and then the tap water valve leading to the water heater should be opened, and the water should enter the water heater and the air should be discharged.

Set the desired water temperature, then plug the power plug into the socket, turn on the switch of the water heater, and the red light will indicate that everything is normal, and the heating will start. When the yellow light is on and the red light is off, the heating has stopped, the water temperature has reached the requirements, and the water can be discharged. In addition, when using a storage type electric water heater, be sure to fill it with cold water before heating it with electricity.

Only when the hot water valve is opened and water flows out can the electricity be turned on. At the same time, when using a storage type electric water heater, the tap water is required to be in a normally open state to ensure that the water tank is always available. When using an electric water heater, if the water valve is opened and no water comes out, the power must be disconnected immediately, otherwise, the electric water heater will be burned out due to the operation of the electric water heater without flowing water.

The electric water heater should be bathed regularly. The water quality and hardness vary from region to region, and the cleaning cycle is different. Generally, the area south of the Yangtze River can be cleaned once a year, and the area to the north, especially near the Yellow River Basin, is generally best cleaned once every six months.

After the water is applied, it is energized to prevent the new machine from drying up. Note that the power is turned off first and then the water is turned off. After a long time, clean the filter screen of the water purification inside.

Replace the magnesium rod regularly to achieve the purpose of maintaining the inner tank. Clean the water heater regularly to prolong the service life of the inner tank. Be sure to fill it with cold water before heating it with electricity.

And the tap water is required to be in a normally open state to ensure that the water tank is always water. In order to prevent scalding, you can open the cold water valve first, and then open the hot water valve; When closing, close the hot water valve first, and then turn off the cold water valve. Before heating the electric water heater, make sure that the mixing valve is closed, that is, you need to press the handle.

This prevents the sprinkler from spilling on the body or wasting it after opening the inlet valve. The inlet valve of the electric water heater needs to be opened before use and when heating, at this time, in order to avoid damage to the electric water heater by dry boiling.

Take a bath often, the bathroom is relatively closed, and after the electric water heater has finished heating the water, unplug it to avoid electric shock due to moisture; The plug is close to the faucet, sprinkler, etc., and it is easy to be electrocuted, so the plug should be unplugged; If the electric water heater has been used for a long time and the inner tank has not been replaced, the plug should be unplugged after heating the water; The purchased electric water heater failed to ensure quality and had to be unplugged. Storage water heater: It has a large capacity and low power, and it takes a long time to heat, so if you turn off the power every time you use it, you will have to wait for a long time for the next use.

The advantage is that it is cheap, the water temperature is stable, and some can be set with a timed heating function, which is very cheap when the time-based billing meter is used. The biggest disadvantage is that the power cannot be turned off, otherwise it will take a long time to use it, and it is easy to form scale.

The correct installation and use of electric water heaters.

1. Align the power plug of the electric water heater that can be used normally with the socket.

2. Twist the two valves under the electric water heater at the same time, one is the valve that flows out of hot water, and the other is the valve that injects cold water.

3. Find the thermostat on the electric water heater, set the temperature according to your needs, and when the water temperature is set, the thermostat will be automatically turned on.

4. Adjust the temperature of use, when using hot water, you can adjust the temperature of the water by rotating the faucet. Generally speaking, rotating in the red (or H) direction is hot water, and rotating in the blue (C) direction is cold water.

5. If you don't use it often, you can choose a quick-heating electric water heater, which only takes 15 minutes to heat up, with fast heating speed and short waiting time.

How do you clean an electric water heater?

1. Usually, the electric water heater will plan a sewage outlet around the inlet and outlet, maybe we don't pay attention to the electric water heater equipment, usually the sewage outlet will not be used, only when the need for cleaning, the sewage outlet will be used.

2. Originally, the principle of the sewage outlet is very simple, pry open the sewage outlet, let the water in the inner tank flow out naturally, and take away some accumulated impurities and scale. However, it has basically no effect on the scale attached to the inner tank and magnesium rod.

3. Clean the water heater through the sewage outlet, preferably cut off the power, turn off the water inlet valve, and after the hot water in the tank cools, open the sewage outlet to let the sewage flow out, and then open the water inlet valve after the sewage in the inner tank is gone, so that the tap water flows into the inner tank and then flows out from the sewage outlet.

4. Clean the electric water heater through the sewage outlet, it is better to disassemble the electric water heater and put it on the ground to prevent sewage from splashing. Most of the scale inside the old electric water heater is attached to the magnesium rod and the inner side of the inner tank, and it is simply cleaned through the sewage outlet, and the effect is not significant.

How do you put water in an electric water heater?

1. Close the water inlet valve, open the water outlet valve, and lift the safety valve handle, this method has a slow drainage speed.

2. Close the water inlet valve, lower the mixing valve and safety valve, and the water discharge speed is faster.

3. Close the water inlet valve, open the water outlet valve, lower the sewage outlet nut, and the water discharge speed is fast.

With the improvement of people's living standards, more and more families use electric water heaters for washing, electric water heaters are not only easy to install, but also not complicated to use, and can also provide users with convenient domestic hot water, so what is the correct way to use electric water heaters? Let's take a look.

What is the correct way to use an electric water heater?

1. When the electric water heater has just been bought, it generally cannot be used immediately, it should be installed in a suitable position in the bathroom first, and then debugged to see if the electric water heater will be abnormal during operation, and after making sure that the water heater can operate normally, it can be used by the family.

2. In order to effectively avoid electric shock, the socket of the electric water heater should also have a reliable grounding wire, and a leakage protection device should be installed in the household power supply system. Since the power of the electric water heater will be relatively large, the electric water heater must use 4 flat wires and three-pin sockets.

3. When using an electric water heater, you also need to pay attention to the type of electric water heater, if the electric water heater is a storage electric water heater, you need to fill the electric water heater with water first, and then start heating, after heating, you can use the electric water heater.

4. If the electric water heater is an instantaneous electric water heater, you don't need to fill the electric water heater with water first, as long as you directly turn on the power of the electric water heater and then turn on the faucet, you can release hot water. Instantaneous electric water heaters generally need to wait about five seconds for them to finish heating, and the water temperature is generally in a moderate state.

5. In order to ensure the health of yourself and your family, it is recommended that you regularly use tools such as a voltage tester to check the leakage protection device at home.

6. After the electric water heater has been used for a long time, the inner tank is generally easy to accumulate dirt, if the dirt is not cleaned up, it will lead to the heating effect of the electric water heater getting worse and worse, and the power consumption is increasing, so it is recommended that you must clean the inner tank regularly.

7. In order to avoid scalding yourself, it is recommended that you do not set the temperature of the electric water heater too high, under normal circumstances, you can set the temperature of the electric water heater at about 42 degrees, and in winter, you can set the temperature of the electric water heater at about 46 degrees.

8. If the electric water heater is not used often, you only need to turn on the power of the electric water heater for heating one hour before use, and then turn off the power after use. If you use the electric water heater frequently, you should not turn the power of the electric water heater on and off frequently, otherwise it is easy to damage the electric water heater.

The above is a detailed introduction to the correct use of electric water heaters, I hope it can help you. The use of electric water heaters will generally affect the service life of electric water heaters, so everyone must master the correct use methods to avoid problems.

Introduction: Many residents have gradually eliminated solar water heaters at home, and choose new storage electric water heaters, but they should also pay attention to the use of electric water heaters, if the operation is not standardized, it will also bring great inconvenience to their lives. <>

When you install a water heater at home, don't turn on the switch of the water heater directly, but after the power is turned on, wait for the tap water to fill the entire water heater, and then turn on the switch of the water heater when the water is full. If you turn on the switch directly before injecting tap water into the water heater, it is easy to cause problems with the internal wiring of the water heater, which is also a situation that manufacturers and users do not want to see. Therefore, when you install a water heater, you must first read the production instructions or ask the merchant how to use it, so as to ensure that you will not have non-standard behaviors during the installation of the water heater and the use of the water heater.

When you use the water heater, you must let it preheat it for 30 to 40 minutes until its light shows red, then you can adjust the temperature of the water heater according to the temperature of the water you usually need. Set a temperature and the temperature of the water will be similar to the set temperature when used. The temperature of the water heater can be adjusted to not be too high, so that it is convenient for everyone to use it in the state disturbance life without burning their hands, probably.

Thirty or forty degrees of water is enough for everyone's daily needs, whether it is bathing or washing dishes, the water temperature is also very comfortable. <>

Because the loss caused by the leakage of the water heater will also occur, we can install an anti-electric wall near the water heater to prevent the leakage of electricity when the water heater is working, which will cause great harm to the human body, and it is also easy to cause fire and other phenomena. And there are many such news on the Internet, such as taking a shower and leaking electricity, being electrocuted, so everyone must use the water heater correctly in life.