There are several ways to install the gypsum line, and how to install the gypsum line

Before installing the gypsum line, the base treatment should be done, and the parts to be installed should be coated with water with a roller and the original putty powder should be removed with a shovel to ensure that the surface of the repaired wall paste position is flat and there is no protrusion or recess. To determine the baseline of the installation according to the width of the plaster line, use an ink fountain to flick the ink line. In the gypsum line of more than 15cm, glue it with adhesive powder, and then fix it with wooden screws or air nails.

Start the construction from the wall opposite the entrance to ensure that the decorative wall is clean and tidy.

1. First of all, clean the wall, in order to prevent the gypsum line from falling off after the phenomenon of falling off, do a good job of removing the residual putty on the original wall base until the cement layer mortar plastering layer is exposed, and then mix glue with other solvents to make a glue liquid for later use, choose the point installation method, and apply the prepared fast adhesive powder horizontally on the back of the selected gypsum line, the interval between the two points can not be too large, and the appropriate distance can be used to reduce the waste of materials.

2. After pasting the gypsum line on the wall at an angle, you must press hard, and then apply the extruded fast-adhesive powder to the gap with your fingers. After pasting, check the plaster line to see if there are any gaps in the edges of the plaster line.

3. The gypsum line linked to the wall must be connected together after the surface pattern must be adjusted to form a finished pattern decoration, which plays the role of decorating the gypsum line. If you encounter the position of the corner of the wall, you should first make a slope type wooden square with the size and shape of the gypsum line, fix the wooden square with self-tapping nails, and then install the gypsum line, so that the gypsum line will not appear with a gap at the junction of the wall at different turns.

Nail line method installation:

1. Remove the residual putty on the base layer of the wall until the cement mortar plastering layer is exposed. This is done to prevent the plaster line from falling off after it is done.

2. Make 10mm holes in the position of the wire groove on the gypsum line mold, at least two.

3. Put the gypsum line mold with holes on the position where the gypsum line needs to be installed, and mark the positions of the two holes with a pencil.

4. Use an electric hammer drill to drill holes in the wall punching positions marked in the previous step, and plug wooden plugs or plastic plugs into the holes.

5. To install the gypsum line, at least two people are needed, one person fixes the gypsum line with self-tapping nails, and one person holds the gypsum line with his hand.

6. If the position of the gypsum line is in the corner of the wall, it is necessary to make a slope wood square with the size and shape of the gypsum line. Fix the wooden square with self-tapping nails first, and then install the gypsum line.

Adhesive installation:

1. The first step is the same as the nail line method. Remove any remaining putty from the base layer of the wall until the cement mortar plastering layer is exposed. This is done to prevent the plaster line from falling off after it is done.

2. Use glue mixed with other solvents to prepare a quick-sticking powder that can be adjusted at any time to reduce the waste of materials.

3. Choose the point installation method, whether it is horizontal or longitudinal, the spacing between the points should not be too far.

4. Paste the gypsum line with the prepared fast adhesive powder, and after pasting, you should immediately gently press the gypsum line with your hand for at least one minute. This is done to make the plaster line paste more firm.

5. Check whether there is a gap, and if there is, use fast adhesive powder to fill the gap.

6. Use a clean rag or brush dipped in a little water to wipe the surface of the gypsum line.

1. The first step is to cut the plaster. Cut the plaster to the desired size, shape and angle;

2. The second step is to apply foam glue. Apply the foam glue evenly to the reverse side of the clean plaster, which can play a good fixing role;

3. The third step is to fix the gypsum line. Before the foam glue dries, fix the plaster line with a fine nail to the desired position.

1. Check whether the wall is clean before installation. The top angle line of the gypsum must be adjusted neatly.

2. If there is a piece of sticky powder on the surface of the gypsum line, clean the surface of the gypsum line with a brush dipped in water before it is completely dry.

3. There should be no gap between the gypsum line and the wall.

4. The folded surface should be repaired neatly.

Gypsum line installation steps:

1. Selection and cleaning of gypsum line molds: Before this, it is important to choose high-quality molds, and the mold pattern should be clear, the three-dimensional degree should be high, and it should be smooth and flat. The mold must be carefully cleaned with drag paste, and the inside of the gypsum line mold must be cleaned, and the inside of the fine seams of the pattern must be carefully cleaned;

If the plaster line mold is severely deformed due to aging, it can be soaked in high-temperature water, and it is emphasized here that the discomfort of the soaking temperature may lead to permanent damage to the mold.

2. Fixed gypsum mold: First of all, the mold should be clamped with a clamp with strong clamping force, and attention must be paid to the value retention level with the glass table top or marble table top when clamping, otherwise the gypsum line will lead to the gap of the finished product that is often said to be "wrong".

3. Gypsum powder slurry: choose the right spoon, the size of the spoon needs to be proportional to the width and thickness of the production of gypsum lines, the wider and thicker the lines need more gypsum powder, and the larger the spoon selected. Add water to a spoon and sprinkle with gypsum powder.

4. Fill gypsum slurry: evenly wipe the adjusted gypsum slurry into the gypsum line mold until the gypsum slurry completely covers the front of the entire mold, and the thickness reaches more than 5mm, and then add glass fiber or mesh;

A sturdy string is added to one end, then covered with a layer of plaster slurry and scraped flat with a special mold scraper. Here we emphasize again that the thickness must meet the standard, do not cut corners, the gains outweigh the losses, and eventually lead to easy fracture or deformation during demoulding.

5. Gypsum line demoulding: After the plaster line is basically solidified, remove the mold clamp, gently shake off the mold, use light force, and pay attention to hand cleaning so as not to leave dirt on the white line.

6. Drying: Hang the plaster line vertically (the rope added in the fourth part) to dry, and if it is an arc-shaped gypsum line or special-shaped gypsum line, it will be placed flat and air-dried.

After the gypsum line is selected, first measure the length of the part where the gypsum line is to be installed, intercept the gypsum line that is suitable for the length, and make preparations. Generally, there are two installation methods for gypsum lines, namely nail line installation method and adhesive line installation method.

1. Nail line installation method:

Steps: 1. First of all, the wall should be cleaned, and then holes should be made in the mold of the gypsum line, and two holes of about one centimeter should be made in the place where the line groove is depicted.

2. Put the perforated gypsum line mold to the place where the gypsum line is to be installed, and mark the perforated position in the corresponding place with a pencil. Use a one-centimetre drill to drill a hole in the marked area, and don't forget to stuff it with something like wood or plastic to make it pop when you're done.

3. In the last step, one person is responsible for supporting the gypsum line, and the other person uses self-tapping nails to install the gypsum line, so at this step, two people must work at the same time.

Second, the adhesive wire installation method:

Steps: 1. The first step is to clean the wall.

The wall must be cleaned, otherwise the plaster line may fall off. Use a shovel or roller to clean off the putty powder on the part to be installed, generally to expose the cement layer in the wall. The speed of preparing fast sticky powder is still relatively fast, so it can be used at any time when you want to stick, so as not to cause unnecessary waste.

2. Apply quick-adhesive powder on both sides of the limestone line, quickly fit it according to the angle, and press hard for one to three minutes.

If there is a quick sticky powder leaking out, apply it evenly with your fingers, check whether there is a gap, and if so, make up the gap immediately to ensure that the stone breeding line can be firmly pasted.

3. Finally, use a rag or brush dipped in clean water to brush the joints, and clean up the stone on the surface to facilitate future cleaning work.

It is possible to paste the gypsum powder with glue, the gypsum powder is added to the special adhesive glue of the gypsum line, the store that buys the gypsum line has a kind of sticky powder, as long as the water is mixed and stirred, it can be pasted, when the gypsum line is pasted, the powder should be adjusted evenly first, and then the back of the gypsum line should be scraped, and then pasted to the wall, and it can also be fixed with screws in the next section.

Use white latex with gypsum powder to stick and cut the corner at 45 degrees, and the seam is not good, and you can repair it with putty.

In fact, there is no need to sell the gypsum line for installation, generally**is 9 cents per meter in Xi'an**.

100 meters is 90 yuan, and you can save a lot of effort.

The plaster line is glued to the wall with quick-tack powder. The plaster line is made of a different material than the wall, so cracks often occur. You can find a small handful of putty powder (a little is enough), live into a mud and rub it on the cracks with your hands, level it, and then apply wall paint or paint when it is dry.

I am a professional installer of gypsum line, and there are two ways to install gypsum line, one is to glue it with quick-adhesive powder. The other is gypsum powder and glue, it can be said that gypsum powder and glue are better, but you have to use special glue, other glue is too slow, if there is old powder on the wall, you must shovel the glue on the map to avoid cracks in the future, and there are a few screws in the window box and where there is wood, maybe the gun will hit a few so as not to shrink and crack.

Do you know how plaster moulding is installed? Explain the whole installation process to you, don't make a mistake.

Stained with latex paint.

Gypsum line installation method.

1. Adhesive method. If there is putty on the original wall, remove it until the cement layer is exposed (this is very important, otherwise the plaster line will continue to fall off in the future). Then use glue to adjust the sticky powder quickly, and adjust it as you use it to avoid waste.

You can apply it in a dot style, but the interval between the two points should not be too large, and the gypsum line must be pressed hard after being pasted at an angle, and then apply the extruded fast-adhesive powder to the gap with your fingers, and finally use a brush dipped in water to brush the joints of the gypsum line.

2. Nailing method. Drill two 1 cm holes in the place where there is a wire groove in the gypsum line mold, for example, the gypsum line is 2 meters long, drill a hole 55 cm in the middle of the two ends, and then put it in the position to be installed and draw the position of the hole with a pencil. Take it off, drill it with a 1 cm electric drill, and insert a plastic plug or wooden stopper.

One holds down the plaster line, and one fixes it with self-tapping nails.

The gypsum line stare mold is not only ***, but also affordable, and the aesthetics are also quite good, so it has been widely used in modern home decoration, but many owners do not know much about the installation method of the gypsum line, so what are the installation methods of the gypsum line? What should I pay attention to when installing gypsum line? Let's take a look!

1. What are the installation methods of gypsum line?

The gypsum line installation method is divided into nail line method and sticking line method: 1. Nail line method, drill two ten mm holes on the gypsum line mold, put the mold in the place to be installed, draw the position of the two holes with a pencil, drill the hole with an electric hammer and put in the wooden stopper, and then fix it with a self-tapping nail; 2. Sticking line method, shovel the base putty until the cement mortar layer is exposed, then bond with instant adhesive, press and hold it hard for a while, and then apply the overflowing sticky powder to the place where the gap can be seen.

Second, what should be paid attention to in the installation of gypsum line.

1. Before the installation of the gypsum line, the base layer of the installation should be cleaned first, and check whether the wall is flat. When docking the joint part of the gypsum line, the gypsum needs to be scraped first, and during the docking process, it is necessary to ensure that the height is consistent and the texture is consistent.

2. In the process of installing the gypsum line, the construction should first start from the front, so as to ensure that the joint part of the gypsum line on the front is relatively small, so that the construction effect of the gypsum line is more beautiful and smooth, and at the same time, the place that needs to be jointed or less than half is placed in an inconspicuous corner.

3. Because the gypsum will solidify in a short time, in the process of installing the gypsum line, you need to quickly paste the gypsum and adjust it, and quickly make up for the missing part of the gypsum line, solidify the money in the gypsum line, and clean the surrounding position of the gypsum with clean water.

Summary: What are the relevant contents of the gypsum line installation method are introduced here, I hope to help friends in need. The installation method of the gypsum line is different, and the effect of installation and repair is also different, but in order to ensure that the gypsum line achieves the ideal decoration effect, it is recommended that you ask professional construction personnel to operate.

Plaster line has a very powerful decorative effect, which we all should know. Gypsum line will be very beautiful after decorating the house, and it also has the function of moisture and fire prevention, so we generally choose to use it when decorating. So let's introduce the gypsum line installation method and the specific steps of gypsum line installation.

Plaster line has a very powerful decorative effect, which we all should know. Gypsum line will be very beautiful after decorating the house, and it also has the function of moisture and fire prevention, so we generally choose to use it when decorating. So let's introduce the installation method of gypsum line for you?

What are the specific steps for gypsum line installation?

Gypsum line installation method.

First, the installation process of the adhesive wire method:

1. During construction, the base putty must be removed, and at the same time, the cement mortar plastering layer will be exposed, which is actually very important, so as to avoid the situation that the gypsum line continues to fall off. Using glue to adjust the sticky powder quickly is the kind that can be adjusted at any time, which avoids more waste. Point installation can be adopted, but the point interval should not be too large.

The important thing is that after the line is attached to the corner of the wall at an angle, it must be pressed hard for more than one point.

2. Smear the squeezed quick-sticky powder with your fingers to fill in the gaps that can be seen. Also note: immediately after that, you can clean the surface of the plaster line with a brush dipped in water. If you wait until it is completely dry, it will be difficult to handle smooth and flat.

Second, the nail line method installation process:

1.First drill 2 10 mm holes in the gypsum line mold, for example, 2 meters long, 55 cm from the 2 ends to the middle, and then put it in the position to be installed and draw the position of the 2 holes drilled with a pencil, take it down, drill the hole with a 10 mm electric hammer, put the plastic plug or wooden stopper, one person presses the gypsum line, and one person uses self-tapping nails to fix it.

2.The corner of the wall is fixed with the wooden square first, and the wooden square needs to be processed into a slope type according to the size and shape of the gypsum line, and the gypsum line is drilled and then fixed with self-tapping nails.

What are the specific steps for gypsum line installation?

1. At the top corner of the need to install or in other parts of the first cement steel nail nail on the wooden block, the general specification of the wooden block is 15 mm 60 mm 50 mm, the spacing inside is about 330 mm, and the nailing wood block must be consistent with the seam of the slider on the yin angle line.

2. Before installing the place in each corner, the carved slider in the corner line must be cut out of a complete flower, and the sliding edge must be planed off so that the nail place can be glued and covered.

3. Align the good yin angle line with the position of the wooden block on the top corner that has been nailed, push away the carved plug-in, drive in 2 3 round nails, push each nail forward a section, and glue an interface with a glass glue pre-cut carving to cover the nail hole, so that you can achieve a seamless effect.

The above is what we have introduced to you about the installation method of gypsum line? The installation of gypsum line is related to the specific steps of the installation, the installation of the gypsum line also has different ways and methods, and different ways and methods bring different decoration effects, but the specific operation steps can only depend on the situation, because the decoration method of gypsum is more flexible.