I am a beginner and want to use paint free boards to make a shoe cabinet, and what materials are use

It is better to use hot-melt adhesive film for paint-free board to glue edge banding strips for cabinets.

A hot melt adhesive film is a film product with or without release liner that can be conveniently operated continuously or intermittently. It can be widely used in all kinds of fabrics, paper, polymer materials and metal bonding.

Tip 1 of the edge banding of the paint-free board: use the hot-melt adhesive film as the adhesive when banding the edge, first lay the adhesive film on the edge of the paint-free board in the way that the adhesive side is facing down, and then use an electric iron to iron, so that the adhesive film is pasted on the edge of the board, and then the back release paper is torn off to make the adhesive film stay on the paint-free board.

Then the edge banding strip of the paint-free board is attached to the adhesive film and ironed with an electric iron at a temperature of no more than 140 degrees Celsius. Finally, let it cool naturally and trim the edge, pay attention to the planing surface and the board surface at an angle of 20 degrees during trimming.

Tip 2 of the edge banding of paint-free board: use special putty for automobiles to treat the adhesive surface of the board, the method is to use putty as a primer, and after 24 hours, it can be cured and polished smoothly.

The conventional operation first melts the hot melt adhesive with a hot melt glue gun, and then coats it on the PVC edge banding, and then the PVC edge banding strip coated with glue is pressed on the side of the paint-free board, and after waiting for the hot melt adhesive to cool and harden, it can produce a better bonding effect.

Later, there is a new product, which is the PVC edge banding strip that has been well glued, which uses a hot melt adhesive film with release liner to realize the PVC edge banding strip on the back, and when used, as long as the release paper is torn off, it can be bonded to the side of the paint-free board with the heat gun.

No matter what board, use a high environmental protection grade.

At present, the substrates of bookcases are: MDF, solid wood particle board, large core board, laminated lumber, multi-layer board, etc. After the double-sided stickers, they are all paint-free boards.

After veneering, the environmental protection level of the board has E2, E1, E0, F4 stars, and formaldehyde-free environmental protection.

If you want to have a good edge banding effect, you can produce blanking materials in the factory and seal the edges of a large edge banding machine. Preferably with a tone-on-color edge banding. Cabinet panels are edged with millimeter PVC. The door panel is edged with mm PVC.

Paint-free board is the best board in making furniture, so that the board is easy to process, but you should pay attention when choosing this kind of board, you must choose the brand, its quality is more guaranteed, and environmental protection is more up to standard. First of all, it not only plays a role in protecting and beautifying the board, but also sometimes inhibits the release of formaldehyde, so the edge banding treatment of the board is still very important for furniture. Many people will not look at its edge banding effect when choosing a board, in fact, this is the biggest mistake.

First, first of all, when you choose the edge banding, it is best to consider using the same type of product as the ecological board, so that the effect will be better-looking, as long as this can ensure the uniformity of appearance, relatively speaking, it is also more beautiful; Second, when you do edge banding, you can make the hot melt adhesive film bonded, and it is safer to use this product. Edge banding plays a very important role in the paint-free board, you should pay attention to the color of the edge banding strip in the operation, and the color of the board must be unified, so as not to affect its beauty, it is best to use hot melt adhesive film to bond is the best.

There are skills in the edge sealing of the paint-free board wardrobe, and the master teaches you to do this, and it will not fall off firmly.

You can use woodworking nail-free glue, or you can use milky white glue, or resin glue is also OK!

Generally, if the edge is sealed by hand, the U-shaped line is pasted with nail-free glue, and if it is sealed by machine, hot melt glue is used.

You can use a special paint-free glue!

You can saw the wooden lines and seal the edges with white latex

Machine sealing, it is recommended to use PUR hot melt adhesive.

Hello, there are special edge banding, on-site construction, are used edge banding for edge banding.

There is a special edge banding strip where the paint-free board is sold, which is directly glued on, about 5 yuan a piece.

Ecological board is divided into two concepts: narrow and broad. 1.In a broad sense, the eco-board is equivalent to melamine veneer, and its full name is melamine-impregnated adhesive film paper veneer wood-based panel, which is to put paper with different colors or textures into the eco-board tree.

It is soaked in grease adhesive, then dried to a certain degree of cure, and then paved on the surface of particleboard, moisture-proof board, MDF, plywood, blockboard or other hard fiberboard, and hot-pressed decorative board. 2.Narrow.

The ecological board in the sense only refers to the melamine veneer with multi-layer solid wood (plywood) and blockboard (such as Malacca, fir, paulownia, poplar, etc.) used in the middle. It is mainly used in furniture, cabinets, wardrobes, bathroom cabinets and other collars.

The edge banding of modern panel furniture is widely used in straight edge banding, special-shaped edge banding (soft-formed edge banding) and post-forming edge banding. The most common of these is straight edge banding.

As long as the edge banding material used as a substrate complies with the requirements of strips or coils, has a surface that can be pasted, and can be trimmed or milled with woodworking tools. Such as wood, paper, plastic, fiber and some composite materials.

Commonly used are solid wood strips, veneer strips, veneer continuous tape with backing paper, impregnated paper tape for edge banding, and PVC tape.

1. Ordinary PVC wood grain edge banding: At present, PVC wood grain edge banding strips are commonly used in domestic panel furniture edge banding, but its quality is extremely unstable, and the color difference after trimming is very obvious, and it is easy to age and break.

2. ABS edge banding: a new type of edge banding material, which is adopted by a few high-end brands, and its advantages are:

1) The raw materials are exquisite and pure, and they are environmentally friendly and pollution-free;

2) Adopt single-heel extrusion and four-color printing process, with clear texture and natural color, which is different from the domestic transfer film process;

3) The surface has an anti-wear layer, good wear resistance, not easy to fade, not easy to corrode;

4) The raw material contains additives, the color is stable, it will not change color under ultraviolet irradiation, and the color of the section will not have obvious color difference after trimming;

5) Good flexibility, even if it is sealed on a board with a small radius, there will be no wood grain breakage;

6) Good dimensional stability, no excessive shrinkage or expansion due to large temperature difference;

7) The hot-melt glue seam is the smallest after edge banding;

8) After the edge banding strip is used for a period of time, the trimming surface will shine without sticking to the dust and will not blacken.

If it is a paint-free board, it can be matched with a ** edge banding card strip, and if it is a woodworking board with paint, it can be matched with a similar one in the big market according to the paint color.