The master who does wire cutting answers?

I don't think that's a big deal, but if you're really upset, you can take a look.

1. Is there a problem with your discharge intermittent (offset), such as the setting is small;

2. There is also the actual diameter of your wire that is smaller than the one you set.

3. The concentration of that cutting fluid is relatively high.

4. Or the speed of your wire is slow, and the current and voltage attached to the wire are too large.

In general, as long as you can grasp the law of one of his transformations, it's very good, you don't have to be the whole thing, you can set as much as you want, that's already very good.

If you don't give up, thank you for stepping on it.

You are very humorous fast walking wire cutting accuracy is very low, generally positive and negative a wire can be guaranteed but must be in accordance with the standard processing technology, your operation is not a problem, all roads lead to Rome are the same.

Actually, no. You can just change the compensation number. We used to have machines. Every one is different. Therefore, it can only be achieved by changing the compensation number.

You can do a gap compensation and you're good to go!

Just take the amount of compensation you calculated.

No, you should only be a few wires larger than what you want when cutting, because you have to subtract the diameter of the molybdenum wire and the place of discharge corrosion when cutting. For example, if you want to cut a 10mm circle, your cutting point should be a few wires larger than 10mm.

The beginner steps of wire cutting are 1, start-up: turn on the power, press the power switch 2, enter the processing program into the controller 3, and open the wire: press the power switch of the wire to make the electrode wire roller.

1. The EDM wire cutting machine, which belongs to the category of electrical processing, was studied by the former Soviet Union Lazarenko and his wife when they studied the phenomenon and causes of the damage caused by spark discharge corrosion of the switch contact.

2. It was discovered that the instantaneous high temperature of the EDM can melt and oxidize the local metal and be corroded, thus creating and inventing the EDM processing method. The wire cutting machine was also invented in the former Soviet Union in 1960, and China was the first country to use it for industrial production.

3. Free positive ions and electrons accumulate in the field, and soon form a conductive channel that is ionized. At this stage, an electric current is formed between the two plates. As a result, the particles collide with each other countless times, forming a plasma region, which quickly rises to a high temperature of 8,000 to 12,000 degrees.

4. Some materials are melted instantaneously on the surface of the two conductors, and at the same time, due to the vaporization of the electrode and the electrode, a bubble is formed.

Question 1: Is the operation of the wire cutting machine easy to learn? It's very easy to learn, if you study hard, you can do it in a week, you can check this out.

Question 2: Is wire cutting easy to learn, how to learn wire cutting Easy to learn, but it is dirty, it is recommended to learn slow wire walking.

Question 3: Is wire cutting hard to learn? Compared to other processing, it is easy to learn.

Question 4: How can it be so difficult to learn wire cutting without a master! Find a place to be an apprentice for a month.

Question 5: Is wire cutting easy to learn? It's all the same, if you are easy to learn, you can learn it, so why is it easy?

Question 6: Is it difficult to learn CNC wire cutting, (currently just apprenticed in the factory) 20 points I work in a machine tool factory, I want to help you analyze it from my point of view, you can combine your own ideas to judge which one you choose to do. 1. Installation:

In fact, it is generally the after-sales personnel of machine tool manufacturers. The machine tool to the customer first needs to be installed, debugging, this work is relatively simple, if the manufacturer model is less, need to learn less, you can get started in a short time. The work is also not very intense and can be carried out step by step according to the plan.

However, the general factory pure Hongjia installers are actually after-sales personnel, and they also need to deal with problems such as machine tool failures. This requires the accumulation of experience, a full understanding of the mechanical and electrical parts of the machine tool, can judge the cause of the machine tool failure, and propose solutions. Due to the need to occupy the customer's working time, or incur service costs, this needs to be completed as soon as possible, and cannot be repaired too leisurely and slowly.

After the age of 35, it is good to transform into sales, after all, you are very familiar with the internal structure of the machine tool, and you will scare some customers who don't know much. 2. Operation: This entry is relatively high, and it is necessary to master a certain knowledge of CNC programming and processing, which does not require too much manual labor.

But if you don't know how to program, and you're just a simple operator, you basically can't learn anything, and you're just a robot-like person. If you choose this, you must master CNC programming, machining technology, tool parameter setting, etc. In this way, there will be great development in the future.

Generally speaking, it is generally developing towards technology.

Question 7: Is there a master who does CNC wire cutting, I want to learn wire cutting, I don't know if it is difficult, understand it,。。 Wire cutting is not difficult, one or two can be learned by doing the ear book, we are all self-taught, look at the manual.

Compare the instructions yourself, and then under the actual operation, you can learn it quickly.

Question 8: Is wire cutting easy to learn Hello, if someone teaches you wholeheartedly, you can learn it in half a month, if you have a mechanical foundation, you can learn it by yourself according to the manual. I am engaged in the mold industry, wire cutting is self-taught, and the software autop is also easy to learn, which is much simpler than CAD.

Question 9: Do you say it's good to learn wire cutting? ? Is it easy to learn? It's okay, it's pretty studious.