What are the steps to install a smart lock? How to install a smart lock

Measure the thickness of the door, the liner, the square rod and the width of the shaft.

2. Remove the old locks, remove the old locks, after the screws are loosened, it is faster to twist them by hand, and you must not break the door lock hole.

Once the new lock is fastened to the door panel, measure the safety extension strip and not exceed 5 cm and the square bar or shaft must not exceed 10 cm.

Then change the direction of the lock tongue, use a screwdriver to screw the screws in the clockwise direction when installing the lock body, put the lock cylinder into the hole, and there must be a special screw to lock the lock cylinder.

5. Connect the power cable, the power wire passes through the door handle, connect the power wire to the main board of the outer handle, pull the wire back, and the outer handle fits the door.

The installation steps of the electronic lock are as follows:1) Draw the hole line: Draw the front, back and side lines of the door according to the hole drawing provided by the factory.

2) Draw the opening line on the front of the door: determine the installation height of the door lock, and the height of the handle position is 90cm from the bottom surface of the door

3) Draw the hole line on the back of the door: Draw the line on the back of the door in the same way as above.

4) Draw the side hole line of the door: first draw the center of the side of the door, and press the hole line on the side of the door with the punch.

5) Draw the opening line of the door frame: Be sure to install the lock cylinder, and then open the opening line of the door frame according to the corresponding position of the lock cylinder (according to the requirements of the opening diagram).

6) The opening of the door frame must pay attention to the height of the corresponding lock cylinder.

The installation method of the smart door lock is as follows:

1. Check the accessories.

Before installing a smart door lock, it is essential to open the box and check the smart door lock to confirm that the required accessories and tools are complete. Then read the installation instructions carefully to understand the precautions during the installation process.

2. Remove the old lock.

Before installing the smart door lock, you need to use a screwdriver to remove the old lock first, after the screw is loose, it will be faster to twist it by hand, and be careful not to damage the door lock hole when disassembling.

3. Measurement. After removing the old lock, it is necessary to "try" install the lock body of the electronic door lock into the security door. During installation, the width, thickness and other data of the door panel and the new lock body should be measured.

According to the volume of the existing door lock and the position of the bolts, the opening should be marked on the security door.

4. Opening. Draw the position of the hole to be opened on the door according to the opening diagram, and then make the hole according to the position of the hole drawn. After opening the hole, place the lock body into the door, thread the wire out of the inner panel, and tighten the lock body with four set screws.

5. Install the lock body.

First, the lock body needs to be secured, and then a second calibration is required before it is fully secured. The deadbolt should be positioned to match the original door frame, and most importantly the door lock must not be tilted. To install the lock body, use a screwdriver to screw the screws in clockwise and insert the lock cylinder into the hole.

The lock cylinder must have a special screw to lock the lock cylinder.

6. Mounting the panel.

During the installation of the latch, the front panel does not need to be reversed. The rear panel needs to be reversed, at the construction site, stand inside the door to determine the opening direction of the door, whether it is "push" or "pull", and then adjust the middle screw to the corresponding position, and then judge whether the hinge direction is "left" or "right", and adjust the side screws to the corresponding position.

7. Testing and debugging.

After installing the smart door lock, it needs to be commissioned. First, close the door to detect if the lock body is extending normally and does not sound an alarm, and then verify that the lock body can open the door normally without alarming.

Then test the "Lock" function key, click to lock the door, double tap to open the door, and press and hold to reverse lock to see if it works.

The correct steps for smart lock installation are as follows:

Material preparation: GB2 smart lock, screwdriver, 4 x No. 5 batteries, etc.

1. Adjust the direction of the handle according to the direction of opening the door: after rotating the handle to the direction of pairing with the door, lock the direction adjustment screw of the handle, and rotate the square sleeve at the same time, rotate the handle counterclockwise towards the right axis arrow, and rotate the handle clockwise to the left axis arrow, and install it after confirming that it is correct.

2. Install two M5 connecting posts on the front panel, and adjust the direction of the orange handle according to the direction of the door opening: rotate the handle to the direction paired with the door, and tighten the adjustment screw for the direction of the locking handle.

3. Thread the front panel cable behind the door, align the handle hole with the square axis on the lock body, and load it into the front panel.

4. Connect the front panel cable and the rear panel line, put the square shaft spring into the handle hole, then align the square axis with the handle hole, and the anti-lock ruler intercom bridge line quasi-anti-deadbolt hole, load it into the rear panel, and fix the front and rear panels with two M6 screws.

5. Insert 4 No. 5 batteries, cover the battery cover, lock the battery cover screws, and test whether the key and password can be opened and closed normally.

Smart lock is an emerging security device in recent years, compared with traditional door locks, it can provide us with more secure protection. Installing a smart lock correctly is the key to ensuring safety, and here are the steps to install it:

The first step is to measure the size of the door lock. Measure the size and spacing of the holes according to the door thickness to ensure that the holes where the smart lock is installed are aligned with the original door lock hole.

The second step is to install the lock box. Insert the lock box inside the door, secure it with bolts, and place the deadbolt into the lock box.

The third step is to install the enclosure. Installing the enclosure requires inserting it into the lock box and securing it with screws. This is preceded by turning the movement downwards and making sure that it is correctly placed.

Fourth, install the battery. Smart locks typically use four AA alkaline batteries, so you'll need to remove the case first, and then follow the instructions to place the batteries in the dust booth at the designated location.

The above five steps are the basic steps to install a smart lock to ensure relatively basic security. Finally, we need the administrator to set the key or password, and issue a sensitive and closed authorization for the smart lock, so that the relevant personnel can enter and exit normally.

How to install a smart lock – the process of installing a smart door lock

1.Painted Zen Hole Line: According to the opening diagram provided by the factory, the front, back and side lines of the door are all there.

The specific drawings are specific hole drawings). Draw the front and back of the door. Determine the height of the door lock installation, the height of the handle position at the bottom of the door is 90cm, (the old door is modified Sun raid type, the door is still the same).

According to the hole diagram, the line of the hole is the side hole that pulls out the door: first draw the center of the side of the door, and press the side opening line of the door to punch the hole. Draw the opening line of the door frame:

After installing the lock cylinder, open the opening line of the door frame according to the corresponding position of the lock cylinder (according to the requirements of the hole drawing). The opening of the door frame must pay attention to the height of the corresponding lock cylinder.

2.Opening: First open the front and back holes according to the drawn opening line.

Take care to prevent the wood fibers from being sanded when opening the holes (it is best to cut the fibers along the open line with a knife) to prevent large openings. Then open the door frame door opening according to the drawn opening line. Note:

The hole size of the door frame is required to be high, which prevents the virtual position, which causes the door lock to vibrate.

3.With door lock: After opening the bag, first check whether the door lock parts are complete, whether the direction is the same as the room, and test the computer lock cylinder and circuit board with the battery, and then start to install the door lock. The lock cylinder is locked as the door panel, the terminal head penetrates the inner side panel, and all the fixing holes are compliant.

requirements. 4.Equipped with mechanical lock: Install the mechanical lock into the lock cylinder and fix it with screws, check whether the mechanical key can open the door when installing the front and rear locks, adjust the lock cylinder to turn the four corners to the correct position (the four corner sleeves have inner holes to put square shafts and springs), load the front lock body door panel.

With the popularity of smart BAI locks, smart locks have now become the first choice for enterprises, businesses and home users. In order to help you install smart locks correctly, the following is an introduction to the precautions for smart lock installation:

1. When opening a hole on the door frame, be sure to measure the distance between the hole to be opened and the edge of the door frame according to the thickness of the door (to measure accurately, otherwise the deadbolt will not be able to pop out and cannot lock the door due to the wrong position, or the door gap gap is too large to cause the door to swing back and forth slightly, which will lead to the feeling that the door is not tightly closed).

2. Smart lock is a high-tech product, the environment in which the door lock should be used plays an important role in the normal use of the door lock, especially in the environment where dust or air contains a high amount of corrosive substances, which will greatly affect the normal use of the door lock. Therefore, it is recommended that you install the door lock after the room has been renovated, so as to facilitate the normal use of the door lock and prolong the service life of the door lock.

3. The quality of fingerprint door lock installation directly affects the normal use and service life of the door lock, it is recommended that experienced personnel install it, 4. Because the door opening method of the lock is different, the opening hole position on the installation mold is not the same, so before marking the line, it is necessary to determine which holes on the installation mold are the holes that need to be opened according to the door opening method of the lock.

5. After the installation and commissioning of the door lock is completed, please register the administrator in time In order to facilitate you to better use the fingerprint door lock, we recommend that when you register your fingerprint, it is best to back up and register a fingerprint or a set of passwords, so that you can open the door normally in the event of an accident such as fingerprint wear.

6. Connection of wires: The connection of wires must be ensured to be correct, and then the connecting wires should be placed to prevent the wires from being crushed or broken by the heaven and earth rods, otherwise the door lock will not work normally.

7. In order to facilitate the opening of the door, before installing the door lock, the distance between the lock and the ground should be measured according to the opening habits of the family.

If you buy a smart door lock at home, you must first understand the steps of installation. How to install a smart door lock? PChouse will take you to find out.

1) Draw the hole line: Draw the front, back and side lines of the door according to the hole drawing provided by the factory. (See the specific drawings for the specific opening diagram).

Draw the opening line on the front and back of the door: determine the installation height of the door lock, and the height of the handle position is 90cm from the bottom surface of the door.

2. Open the door: first open the front hole and the back hole according to the drawn hole line. It is necessary to pay attention to prevent the wood fiber from flashing when opening the hole (it is best to cut the fiber along the opening line with a cutter first) to prevent the opening from being too large. Then press the drawn opening line to open the door frame and door hole.

3. Install the door lock: After opening the packing box, first check whether the door lock parts are complete, whether the direction is consistent with the room, and test whether the computer lock cylinder and circuit board are working properly with the battery, and then start to install the door lock. Install the lock cylinder into the door plate, thread the terminal head into the inner side plate, and all the fixing holes meet the requirements.

4. Install a mechanical lock: Install the mechanical lock into the lock cylinder and fix it with screws to check whether the mechanical key can open the door. When installing the front and rear lock bodies, adjust the idling four-corner sleeve of the lock cylinder to the correct position (the inner hole of the four-corner sleeve has a logo, place the square shaft and spring), and install the front lock body on the door plate.

After installing the door lock, don't forget that when the user officially puts it into use after the door lock is installed, it must resend a new "time card" from the door lock software to insert (or lean) on all door locks, and after a "tick", the door lock time is confirmed to be installed normally after the current correct time.