Huangming solar electric heating leakage tripping what s going on, electric heating is good wires ar

Hello! Sorry for the inconvenience.

The cause of this phenomenon may be the poor contact of the leakage protection plug, measures: check the socket and leakage protection plug to ensure that the contact is good; The overheat protector trips a, cuts off the power supply and resets, and turns on the water after 20 minutes (at night or under no light conditions); b. Reset after troubleshooting, if it still trips, replace the overheating protector, which needs to be solved by our professionals.

You can also log in to the official climate improvement of Huangming Solar**(

Consult the after-sales maintenance hotline of Huangming Solar or call the national unified after-sales service of Huangming Solar**400-813-2222 for consultation.

I wish you a happy life, you can ask any questions at any time, and I will answer them for you in a timely manner.

The reason for the leakage protection plug tripping, 1. Check the leakage protection, shake the leakage protection, the leakage protection makes a sound, and replace the leakage protection; 2. Open the lid at the electric heating pipe of the water tank to see if there is any water leakage here, and the wiring of the electric heating pipe will trip if it is wet; 3. The line is exposed.

When you say that the electricity is well heated, it is measured by an electric meter. Very unreliable! It is likely that the heating wire in the electric heating tube is attached to the pipe wall. On closer inspection, this is more dangerous.

See if it is his high power, and the small power of your home meter always causes tripping, this can be replaced with a meter with a large current.

Leakage protector is used to effectively protect the direct electric shock and indirect contact of the low-voltage power grid, and can also be used as the phase loss protection of the three-phase motor. It is available in single-phase and three-phase. How it works.

Because it uses the leakage current or the resulting neutral point to ground voltage change as the action signal, it does not need to set the action value with the current value, so the sensitivity is high, and the power supply can be effectively cut off after the action to ensure personal safety.

Electric heating problems, there is a 70 degree protection may be broken,

Is it new??

Is it that the zero line is not leaked?

The installation angle deviation is too large or there is a certain area of obstruction above the water heater, resulting in insufficient light and serious dust coverage on the surface of the vacuum tube, the dust should be cleaned up in time, and the poor water quality causes the accumulation of sediment or scaling in the pipe, the vacuum pipe should be cleaned, and the necessary check valve is not installed according to the installation requirements, resulting in the loss of hot water, and the installation should be carried out in strict accordance with the requirements, and the system fails, and the water inlet can not be stopped or the solenoid valve leaks to cause hot water overflow, this problem is the most common, and the necessary check valve is not installed according to the installation requirements. Once there is an internal leak in the user's water appliance, it will cause the phenomenon of cold water backflow through the hot water pipe. If there is a check valve, the amount of water returned is very small, because the user is still using water, so the impact on the system is not large, if there is no check valve, the cold water return is not obstructed, it will cause the water tank to be full, the hot water on the top of the pure smile tank continues to lose, the user will feel that the solar energy does not work, the water is not hot, the insulation measures are insufficient, resulting in a large amount of heat loss, or the host has serious heat loss, especially in the north, to strengthen the insulation of the water pipe, the connection and treatment of the outlet of the water tank should be cautious, Prevents heat loss.

Common faults of Huangming solar water heaters.

Second, the solar water heater has no water coming down.

Reason: The water of the solar water tank has been used up and needs to be re-reloaded, and the control system is faulty, especially the failure of the sensor, resulting in the wrong water level indication, and the water replenishment system cannot be started to replenish water in time, and the pipeline is blocked.

Common faults of Huangming solar water heaters.

3. Leakage of solar water tank.

Reason: The vacuum tube sealing ring is not properly enclosed at the bile duct mouth in the water tank; The seal is damaged after repeated use; The sealing ring is not clean, and there are debris, such as foaming liquid film, etc.

Common faults of Huangming solar water heaters.

Fourth, the solar water tank can not be filled with water or cannot be filled with water.

Cause: Damaged solenoid valve or controller failure, which is also a frequent failure.

Common faults of Huangming solar water heaters.

Fifth, the effluent pressure is not enough.

Reason: manifested in the fact that the water output from the faucet is very small; When using a shower, the shower does not form a water column; When using a mixing faucet, there is always cold water but no hot water. The reason for these cases is that the water pressure is too low.

The solar water heater is non-pressure operation, its water supply is equivalent to the roof water tank water supply, the water heater tank should be regarded as another roof water tank, the water pressure is determined by the height difference between the solar water tank and the user's water appliances, the height difference is 10 meters, and the water pressure increases by 1 kg. Under normal circumstances, the water pressure with a height difference of more than 5 meters can be used, that is, every other floor, if the user still thinks that the water pressure is too small, you can add a booster water pump in the pipeline to solve it.

Common faults of Huangming solar water heaters.

6. Too much cold water is released when using hot water.

Reasons: 1. The most commonly used method is hot water circulation, 2. It is used in conjunction with electric water heaters and gas water heaters, 3. There are some solutions to pipe circulation, readers can try it: