How to set the network speed of Leike router NW737

Looking at your screenshots, you probably want to limit other people's Internet speeds.

The default host connection limit" can be used by default, that is, the above two options are 1024 and 0, and the main purpose is to set the "specific host connection number configuration", which is to limit the network speed of others.

- This is based on the range of your DHCP, so take a closer look at the DHCP.

- Use a fixed IP address for your own computer, and the IP address should not be within the DHCP range. Other computers that want to throttle the internet speed will be automatically acquired with an IP address.

Number of single-host connections: 200 recommended

Total number of host segment connections: 600 recommended

- You can try this number first to see the effect, and then change it if it doesn't work.

Use your IP address, username, and password (prompted on the back of the router) and enter the address bar of your browser.

DHCP Service Client List View which clients need to be controlled, and record information such as host IP addresses.

IP Bandwidth Control Add a new entry (see message above).

Enter the IP address and uplink and downlink bandwidth (reasonably allocated according to the requirements) Enable Save.

Fill in the data reference:

The following parameters need to be set for IP bandwidth control:

Enable IP Bandwidth Control: If enabled, the bandwidth control rule will work.

Broadband line type: If the Internet access mode is ADSL broadband Internet access, please select "ADSL line", otherwise please select "Other line".

Total uplink bandwidth: The upload speed that can be provided through the WAN port.

The IP bandwidth control entry contains the following fields:

id: indicates the first rule.

Uplink bandwidth: If the maximum upload speed allowed through the WAN port and the minimum upload speed are guaranteed, the default value is used.

Enabled: The status of the rule, indicating whether the rule takes effect.

Configuration: You can perform and delete actions on rules.

References Routing Control Bandwidth.

and priority between different groups of computers!

I believe that if these parameters are set reasonably, all computers in the LAN should have a better Internet experience.

1. If you turn on smart wireless (smart QoS), you don't need to set the following speed limit, the routing is set automatically, as long as you turn on QoS broadband and application priority.

The setting method of Leike NW736 wireless router is as follows:

1. The broadband bus (the network cable from the cat) connects to the WAN port of the router.

2. Connect one end of the network cable to any LAN port of the router, and connect the other end to the computer, and start the computer and router equipment;

3. After starting the device, open the browser and enter it in the address bar to enter the wireless router settings interface.

4. An account and password to log in to the router appear in the settings interface, enter the default account and password admin

5. According to the setting wizard step by step setting, select the Internet mode, usually ADSL users choose the first PPPoE, if you use other network service providers, select the following two according to the actual situation, if you don't know how to choose, directly select the first item to automatically select, convenient for novice operations, click next after selection;

6. Enter the account and password applied for from the network service provider, and go directly to the next step after the input is completed;

7. Set the wifi password, try to make the alphanumeric combination more complicated and not easy to be rubbed off the network.

8. After entering correctly, it will prompt whether to restart the router, select Yes to confirm the restart of the router, and you can access the Internet normally after restarting the router.

The method of the Leike NW736 router is as follows:

1. Plug the network cable from Telecom into the WAN port of the router and the LAN port of the router into the computer first;

2. Then set the IP address in the computer to or automatically obtain) (the last digit of the address is non-1), the subnet mask is, and the gateway is;

4. Generally, broadband is PPPoE dial-up Internet access, select "WAN port connection type" as "PPPOE", fill in the Internet account and Internet password provided by the service provider, and select "automatic connection, automatic connection after boot and disconnection";

5. Click "Save" and select "DHCP Server" on the page, click "Enable", fill in the start address (the minimum is and the end address (the maximum is, the address lease period is directly filled in the maximum value, and then click "Save" and select "Restart Router" under "System Tools" on the page, so as to complete the router setting.

Your broadband, don't fill in the password???

Just plug it in and use it, don't you need to dial?

If dial-up is not required, do not select PPPoE mode and select Bridge Over.

How can you not have a password? When you used to connect to the Internet with a broadband connection, did you have no password for the first time you entered your account? Or when you use it, it's a direct dot connection.

Because the broadband connection has entered the account password for the first time, it will be automatically saved, the password column will not show the little star, but write to change the password, please click here, is it wrong?

My house is also mobile... The password is 1234

How did you access the Internet when you were on a single machine? Is it dial-up Internet access, automatic IP access, fixed IP Internet access, or web page authentication Internet access?