SOLVE: I BOUGHT A PTLINK ROUTER BUT NOW I CAN T CONNECT TO THE INTERNET

Look at the prompt on the back of the router, there is the default IP and password of the router here, and then reset the router according to your method. Then connect a single line to a computer, don't connect the router to the cat, try again, if it still doesn't work, the router is broken, it's as simple as that, you think about it, you can't even reset it, it's not a problem with the router.

Now that the router has been reset and your computer has auto-fetch enabled:

Start running cmd ipconfig, what you see here is the gateway, use the ie browser to log in to the default gateway after the ip address to manage the router, it may be.

Since you can access the Internet on a stand-alone machine, it means that the network is fine.

1.Check the WAN port settings of the router, and fill in the settings of the WAN port of the router corresponding to the settings of the stand-alone Internet access to the computer, including the IP address and dial-up (if any) settings, and save it.

2.Confirm that the DHCP feature of the router is enabled.

3.Restart your router.

4.Check the running status of the router and see that all parameters of the WAN port are non-0 and there are non-0 packets, which means that the router has successfully connected the Internet.

What kind of network do you install, whether the broadband, rail, or long and wide of the telecom is connected, first determine whether your broadband network is open (there is a problem with the line or is in arrears).

TP Router IP: Default Account and Password: Admin reboot the router and enter your broadband and password new.

Try again.

Wireless can be used normally, wired cannot be used.

It means that your network is normal, then you have to check it from two points1, change a network cable and try it;

2. Go to the router, take a look at the settings, and turn DHCP on;

3. After connecting the Internet cable, restart the router and give it a try;

4. After plugging in the network cable, change the IP address of the computer to automatically obtained.

Try the above methods one by one, I hope it can help you solve the problem!

Wireless is fine, this problem is at two points.

1. The network cable from the computer to the router is not connected.

2. If the NIC is faulty or the settings are incorrect, the local connection should be set to automatically obtain the IP

Router to wireless router, second router setup, there are two ways (provided that the first router has been set up):

The first method: dynamic IP mode (the first route is the primary route, and the second route is the slave route).

1. Plug in the router and do not connect the LAN port of the main router first, and reset the slave router (restore the factory);

2. Connect the computer from any LAN port of the router to enter the settings page;

3. Set according to the dynamic IP;

4. Then set the SSID, encryption method and password;

5. Save and restart;

6. After setting, connect the network cable from the LAN port of the main router to the WAN port from the router.

The second method: wireless AP mode.

1. Connect the computer to the LAN port of the router first, and change the IP address of the slave router. For example, most router addresses are, we just need to change from router IP address to that;

2. Turn off the DHCP function from the router in the settings;

3. Finally, connect the network cable from the main router to the LAN port of the slave router (any one is fine), note that it cannot be the WAN port.

It is not a fault of the router or the cat or the computer.

It is the network operator who binds your MAC address to the networked server, you need to call the network operator's service**, perform a self-service repair, or transfer to a manual service to ask them to help you do a server data reset, after completion, wait a few minutes, restart the cat and the router, and you can use the router to dial normally.

Of course, you need to rule out a special case: the IP address of the router (which also conflicts with the IP address of some cats with routing functions). In this case, please modify the router LAN setting to use this address when entering the router in the future), restart, and you can.

First, remove the network cable from the WAN port of the router, connect to the computer and dial to see if the broadband line can be dialed normally. If you can connect to the Internet normally, it means that your router is connected to the network cable or set up the wrong one, reset it and set the dial-up again.

If the computer dialing is unsuccessful, confirm that the password is correct. Check whether the broadband modem DSL light is always on and connected normally. Or the broadband cat is powered off, and the power test dial is reconnected after the meeting.

If you can dial the number, it means that the broadband modem crashes. If it often occurs, you need to replace the cat with a warranty, or buy a replacement by yourself.

If the broadband cat DSL light has not been able to connect on, if the ** line is connected, then check whether the ** line is normal, whether it can talk, ** line is normal, it means that it is a broadband provider problem. Make sure that there is no overdue broadband payment. Excluding the above, and the cat DSL light does not light up, you need to call customer service for repair and inspection.

Hope it helps.

Check it out like this:

2. Reseat the network cable once.

The network cable connected by the cat is connected to the WAN port of the wireless router, and the computer is connected to any LAN port of the wireless router.

3. Turn off the cat and the wireless router and turn them on, and take a look later.

Fourth, if it still doesn't work, set up the wireless router again.

Need to dial up the broadband cat to connect the wireless router and you do it:

Plug in the wireless router, don't pick up the cat first, reset the wireless router (restore the factory), connect the computer to any LAN port of the wireless router, enter the router gateway address in the browser address bar (on the label on the back of the router), enter the settings page, and set it according to the PPPoe (ADSL virtual dialing) method.

Then set the SSID, encryption method, and password. Save, restart.

After setting, connect the network cable from the cat god blind lan port to the WAN port of the wireless router.

Do a factory reset, then try to set it up again.