I can t get in after the router is restored, and I can t get in after the router is reset

1.Check the network cable connection and troubleshoot the line.

2.Rereset the route.

Note: To reset the system settings to factory settings, follow these steps:

1.Do not disconnect the DI-504 broadband router from power, 2Press the reset button with the paper clip and hold for 5 seconds, 3

Let go of the button DI-504 will automatically restart. (Note: If you press and hold for less than five seconds, the DI-504 will only reactivate, not restore the settings to factory settings).

You're recovering the factory value! There is a small hole in the router, poke it and don't let it go, see that the lights on the router are all flashing, and it will be restored! And don't you know how to cut the manual?

It's all there! Some of them are not the same, and the way to enter the route is also different!

First, set your motherboard's IP to:

Generally look at the manual of the router, the manufacturer is different, the default IP is different, and the default of TP-Link is generally.

Enter in the address bar.

The password and first name are mostly admin

Then see if it goes in, and if it doesn't work, you can ping the IP:, if not, it must be a problem with the connected line.

No, most routers are...

Most of the passwords and names are admin or guest

Then you try another way, the network neighbor right-click attribute, the local connection right-click attribute, the Internet protocol double-click the left button to open, use the following IP address IP address to play,, the subnet mask does not need to be played, he defaults, the default gateway hits.

Press and hold the route with a pen and don't put it where there is a small eye, remember to plug in the power supply, press and hold for 3 seconds and don't let go, then release the power and press it for 2-4 seconds, and then enter the address bar to enter or If it doesn't work, try a few more times If it doesn't work again, go and change the route.

Press and hold the "Reset" button on the fuselage for 5 seconds. After releasing it, all settings on the router will be restored to factory settings (including IP address, username, password, etc.). At this time, open the browser, enter the default IP address of the router, log in and set it again, and you're good to go.

This depends on what kind of land rover you are.

If you have a land rover.

The gateway defaults.

Just set your computer's IP to any IP within one as above.

Then there's the issue of account numbers and passwords.

Some land-based games have the same account number and password.

Some have accounts and no passwords, and you still have to experiment with them.

There is a general account number.

admin and guest

After you factory reset your computer, you let your computer get its own IP, and then you see if your IP shows up or whatever. If so, you can type it, try a few more times, and you can't restart your computer again. And then on.

Take a look at the instructions above.

Don't just try.

Most of the passwords and names are admin or guest, you try it, this is very easy, it may not be bad, no, and then restart the route, just ......It's not ghost on the first floor, it's a backup ......It's a guest.

Ha ha. Float over ......

You first set the IP address of your computer's local connection to automatic. Then take a look at what the automatically acquired IP address range is. If yes, yes, if yes. And so on ...

The default address of the router is generally.

Check the line, turn off the firewall, log in to the router from the console port to check the configuration, reset, click reset on the router, and change it if it doesn't work.

Look at the instructions and press the reset button according to the instructions. Then connect it and you're good to go. I've been in this situation with you, too. It is the small button that did not press the reset at the time of factory reset.

There are several possibilities:

Is there a network firewall loaded?

2.Is the username and password of the router correct?

3.If it doesn't work, press the little reset button on the router and try it.

It may be that the network cable is not connected, if you are sure that it is connected, restart the route once, and then try again!

You restart the route, or revert to the exit settings. Set your computer's IP like this. You can go in.

Ask about the initial settings of the manufacturer, the general user name is admin, and the password is also admin, which is the information written by the manufacturer into the chip. If it doesn't work, just call ** and ask the manufacturer.

The IP of the router is not necessarily the default, it may be another IP, I have seen the router IP, yes, so you'd better look for the instructions, or go to the official ** to take a look.

Most of the codes and names are admin or guest

You try it, it's easy, it's not bad, it's not good, and then restart the route, it's good to ......

It's not ghost on the first floor, it's a backup ......Yes to come.

Looking at the routing manual, it must be that the IP has changed, it may be waiting, and the password is not necessarily, so it is necessary to analyze the specific problem specifically.

Restart the route and see...

Do you also have the same network segment set to your own network card address?

If you reset the oiler, you can reinstall the system.

Use the reset key to start again, unplug the power supply and plug it in, and use the default username and password should be fine.

The default factory is: (see route manual).

The password and first name are mostly admin

Don't forget to make your computer's IP address the same network segment as well!!

What is the default gateway you connect to, just enter it in the address bar. I've also set up an IP address, so it shouldn't be wrong.

So many ways. If it doesn't work, see if there is still a warranty, and if it doesn't work, go to the repair center to get a new one. How thorough!

An important possibility is missing, is there a problem with your network card or network cable?

The default factory is:

The password and first name are mostly admin

You can point to the route after the factory reset will be operated for a period of time, in this case it will definitely not be accessible. If there is a power-off operation from the start route in this process, the possibility of fixing the problem is relatively large, you can try to press and hold the reset button for 15 seconds in the power-on state of the route to release it for hard reset, and the power cannot be turned off during the operation, and the route should be able to restore the factory state after about 3 minutes. In addition, if the wireless cannot be connected, the problem of routing can be ruled out.

After the factory reset, the IP address and encryption mode settings may have been reset, if the original wireless encryption state becomes unencrypted after the reset, it is usually not connected, delete the original wireless configuration in the wireless management, and connect from the new search wireless signal.

Wireless router purchase:

1. Look at network standards.

Wireless routers are just like smartphones, and as technology gets better and better, the standards of routers are constantly evolving. That's why we have standards like and these are the descriptions of the functional levels of routers. Generally speaking, as long as it is a standard router, it must be dual-band, or tri-band.

As shown in the figure above, the receiving speed of different levels of routers is under the lower level.

2. Look at the port gigabit.

The WAN port and LAN port of the router are divided into gigabit and 100 gigabit. Figure 1 is the parameters of the ASUS AC68U Gigabit router, and Figure 2 is the parameters of the ASUS AC51U Gigabit router.

3. Look at ease of use.

For wireless routers, ease of use is very important, to be reflected in the setting interface, users can set up the router through the computer browser settings or mobile phone, the user only needs to follow the prompts to select the settings, some wireless routers also support remote control of wireless routers. To emphasize, today's routers of Internet companies are easy to use and slightly less stable, while traditional router companies are slightly less usable or do not support remote management, but fortunately, they are stable.

4. Look at the brand.

The first thing most users look at when buying a router is the brand, which is divided into two types of manufacturers: traditional wireless router manufacturers: ASUS, Netgear, Feixun, Linksys, TP-Link, D-Link, Magician, Huawei, etc.

Internet wireless router manufacturers: Polar Router, Xiaomi, Honor, Youku, Thunderbolt, etc.

5. Last look**.

The ** of wireless routers is priced according to their functions, antennas, ports, brands, etc., as the so-called penny, you get what you pay, but cheap wireless routers are not necessarily not easy to use, but expensive wireless routers must have expensive reasons.

To make sure, is your computer connected directly to the reset router with a network cable?

First of all, when the network cable is connected to the router, you check whether you have obtained the IP (check the method, click to start, enter cmd+enter, a black window will appear, and then enter ipconfig all+enter, you can see the ethernet adapter local connection:, whether there is an ipv4 address), if you get it, you enter ping in the black window default gateway (ip), if there is a TTL value, it means that you can ping to the router, If you still can't open the router homepage in this case, it is recommended that you try it in a different browser (such as Firefox).

Also, you can ping in the pop-up black window and then press enter, see if there is a TTL value appear, if there is, it proves that your wired network card is normal (note: in this test, you turn off the wireless first), then you can connect to the wired but can't get the IP is not your computer's problem, you can set a manual IP for your computer to try whether you can access the Internet, as for why you can't get the IP, because it's not your own router, so you can't compete for the network equipment to check the problem.

The reset is not complete.

There are two ways to reset the router: one is to find a thin wire or straightened paper clip, and hold the reset hole (reset) behind the router when the router is powered on, about 10 seconds, after the indicator light on the router is all off and then on, release the reset hole, that is, complete the router reset; After the reset is completed, you need to enter the router settings interface again, and reset the PPPoE account and password to access the Internet; The second is to directly enter the router's settings interface, find the "System Settings" item, which contains the "Restore Router Factory Settings" item, and you can restore it; After the router restarts, go to the settings page and reset the PPPoE account and password.

After you have clear all your browser records, including cookies, etc., try again, and make sure that you have set a fixed IP? If so, change it to automatically obtain an IP address.

After the factory reset, you need to set up your wireless router again.

Need to dial up the broadband cat to connect the wireless router and you do it:

Plug in the wireless router, don't pick up the cat first, reset the wireless router (restore the factory), connect the computer to any LAN port of the wireless router, enter the router gateway address in the browser address bar (on the label behind the router), enter the settings page, and set it according to the PPPoe (ADSL virtual dialing) method.

Then set the SSID, encryption method, and password. Save, restart.

After setting, connect the network cable from the cat LAN port to the WAN port of the wireless router.

After the reset, the router needs to be set up again.

3.First of all, bind your broadband account and password in the broadband Internet account and password settings, and then set the router password and name, after saving, the router can use the new password to connect to the wireless hotspot normally. Resetting the router is to restore the factory settings, and you need to set up the router again, which is equivalent to the first time you install the router and need to set it up.

After resetting the router, you need to reset it before you can access the Internet, and if you need to reset it, at least you need to set the following information:

The account number and password for broadband dial-up (PPPoE dial-up), the network name (SSID) and password of the wireless network connection.

If you forget the broadband account and password, you can call the operator's customer service to obtain or reset it, and the way to obtain the broadband account is to check the broadband account through the account holder's ID card and the mobile phone number reserved at the beginning, and reset the broadband password through the account holder's ID card number and broadband account reset.

The method of resetting is also very simple, you can get the gateway address through the wireless network connection, and then enter the gateway address into the browser, and then set it step by step according to the prompts, or search for the setting method of the corresponding router model on the Internet.

If you reset your router, you have to go through setting up your router before you can surf the Internet, here's how:

1. Log in to the router (for TP-Link routers: turn on your computer, click on IE browser, enter in the address bar: press enter, pop up the login page and enter the username "admin", password "admin", please refer to the router user manual for other routers).

2. Click on the network settings on the left, select Static IP in the WAN port settings, enter the IP, subnet mask, default gateway is, enter DNS1, DNS2.;

3. Turn on the DHCP server;

4. For the wireless router, turn on the wireless network, turn on the wireless network function, and set the wireless login password (security option wpa-psk wpa2-psk, enter the key);

Save the parameters and it's OK,At this time, the desktop has been able to wired the Internet,Then open the wireless network card in the right corner of the desktop to right-click to view the available wireless network,Now your router broadcasts the signal,Double-click to connect,Enter the key to get it。 Wired and wireless access is available.

Configure the IP on the computer to automatically obtain, and in the future, you can go to the Internet by opening the browser directly on the desktop, and finally connect the computer to the network (wired and wireless access are available) to check whether you can access the Internet normally.

If you can't access the Internet, you can only connect to the computer that can access the Internet normally after dialing up the link on the router, log in to the router again, and clone the MAC address in the WAN port settings, and you're OK.