Does the car deviation have anything to do with the tire screws being too tight?

It has nothing to do with the tire screws being too tight...

Tire rotation may not be able to solve the mistracking...

with tire pressure... There is also an uneven braking force on the left and right wheels... Car toe and so on are related...

It is recommended that you do a wheel alignment...

It has nothing to do with the tire Rose is too tight, if you tire front and rear transposition why not do tire dynamic balance, car driving on the front wheel requirements, far more stringent than the rear wheel, the front wheel is the driving wheel, the steering system is also in the front wheel, if you front and rear tire rotation must do dynamic balance, and then measure the two front wheel toe, the front of the tire is 1 to 5 mm smaller than the rear of the tire, whichever,.

It doesn't matter, go and set a position, and if the master of positioning says something bad, you will replace it, and then just go to positioning!

First determine whether the chassis parts are good, for example, the swing arm, the horizontal tie bar, the bracket cushion bushing and the like are not good first, if it is good, the front and rear tires are evenly inflated, put down to open the positive, the toe amount is good, and the adjustment can be good.

No, I guess there is a problem with the dynamic balance of the wheels.

It doesn't matter much, it is recommended to do 4 rounds of positioning.

It has nothing to do with that, maybe the tire pressure is not normal, or the toe-in is recommended to do a four-wheel alignment.

Four-wheel alignment, toe-in measurement, tire pressure check, steering ball joint check.

It doesn't matter, it is recommended to do a four-wheel alignment.

It doesn't matter, just do four-wheel alignment.

The tire is counterclockwise in the direction in which the screws are relaxed, and clockwise is the direction in which the screws are tightened. Since the screws that fix the wheels are tightened, it should be noted that when disassembling the tires to be replaced, do not use a jack to lift the car up, and use a socket wrench to loosen the tire fixing screws in diagonal order.

How to tighten the tire screws:

1. The loosening of the tire screw of the car is in the counterclockwise direction: press the left hand in the direction of the center of the tire, hold the wrench with the right hand and lift it up, and the screw will be loosened;

2. The left and right side directions of the tire screws of large trucks are different, the left (driver's seat) is the inverted tooth, and the right side is the straight tooth, that is, according to the forward rolling direction of the car, it is tightened, and the reverse direction is loosened;

3. Remove the screws diagonally; In this way, the stress of the tire will not be concentrated in one piece, which is more labor-saving, and the screw wear will be a little less.

Steps to remove the tire:

1. Remove the anti-theft cover with the on-board tool.

2. Use a socket wrench to gradually loosen the nut counterclockwise in diagonal order.

3. Use the jack to align the jack special card slot of the car chassis to lift the car.

4. Remove the unscrewed nut and remove the tire.

Precautions for removing tires:

1. Professional tools must be used.

2. It is very difficult to disassemble some run-flat tire models by themselves, and you need to go to a nearby maintenance location to replace them, or call for roadside assistance.

3. Proper use of foot strength can increase the degree of tightening of the nut, but do not blindly kick, causing direct damage to the nut or bolt.

We generally screw the wheels, and it is estimated that the most we should change is the spare tire.

Finish. There must be many friends who think that the tighter the screws, the better, so that the wheels will be strong and there will be no problems, but is this really the case? Obviously: not really!

Generally speaking, car tire screws have a specified torque, but in the actual use of the car, when our car mechanic.

Or when the owner tightens the screws, the actual torque will be greater than the specified torque! Why is this happening? One is because I am afraid that the tire screws will be loose, and the other is that there is no tool to adjust the torque!

Screws that are tightened with all their might are often prone to problems during the actual repair process. According to the auto mechanic, every year there will always be car owners who ask for help because they can't remove the screws and can't change the spare tire! These hard-to-remove screw models are mainly Audi.

Or the Volkswagen model (the tire screws are about the same)!

If we look closely, we can always recall a painting. The buddy who changed the spare tire on the side of the road, when he used the screws to install the tires in Muling, he tightened the tires with all his might. With the man's downward force, the body followed Xunzhen's undulation.

What's more, just like the picture above, I was afraid that I wouldn't be able to tighten the screws, so I kicked my feet directly, and some stood on the wrench.

On the person using the body to press the wrench lock screw. It's ......Definitely not. You know, there are two risks of screwing so hard: one is that the screw is too strong, and the other is that the screw is directly broken. Although this problem has a certain probability, it is still risky

Of course, our car owners don't have to worry too much. Leave it to the auto mechanic. The average experienced master would not make such a mistake!

If you really don't feel at ease, just watch carefully on the side to prevent the auto mechanic from forgetting to tighten a certain screw! It's all a lesson! It's better than doing nothing yourself!

The above is about the tire tightened too tightly caused by the problem of Wang Kai to the west, so when replacing the tire, you still have to pay more attention, if you really have no experience, it is best to find a professional master for maintenance, I hope the above is helpful to everyone!

It may affect the normal driving of the vehicle, it may cause the screw of the tire to break when the tire is broken, it may cause the screw of the tire to fall off when repairing the tire, it will affect the torque of the tire, it may affect the extension of the grinding space, and it may cause the tire and screws to expand and shrink in heat, and the screws are easy to deform.

It may lead to unstable tire pressure, and it will also affect the balance of the car due to lack of traces, and it will also lead to serious tire wear, or Chanzhou attack will cause accidents, and there will be problems with the car engine.

The wheels of the car will fail, the engine of the car will fail, the chassis of the car will fail, the use of the car will be reduced, and the friction of the car will be reduced.

The hazard can easily cause the tire thread mouth to rise, and even cracks.

Automobile tires are one of the important parts of the car, which is in direct contact with the road surface, and the car suspension works together to alleviate the impact of the car when driving, and ensure that the car has good ride comfort and driving smoothness; Ensure good adhesion to the wheels and the road surface.

Improve the traction, braking and passability of the car; Bearing the weight of the car, the important role played by tires in the car is becoming more and more important.

Origins of development. In 1895, with the advent of automobiles, pneumatic tires were widely developed, and the first samples of automobile tires appeared in France in 1895, which were single-tube tires made of plain canvas, although there was tread rubber but no tread.

The tightening direction of the automobile tire screw is judged by counterclockwise, the counterclockwise direction is loosening, and the clockwise direction is tightening. The left and right side of the tire screw of the large truck is not the same, the left is the inverted tooth, the right side is the straight tooth, according to the forward rolling direction of the car is tightened, and the reverse direction is loosened. When removing tires, you should also check whether the tools used and the tire screws are worn out.

If the tire screws are too tight, they can be removed like this:

1. If you find that the tire screws are too tight to be unscrewed, the most direct way is to find one more person to help;

2. We can also pour lubricating solvents like diesel on the screws;

3. You can also increase the tightness of the nut with the help of foot strength, but do not blindly kick it, causing direct damage to the nut or bolt;

4. You can use a hammer and other tools to hammer to the back of the tire wrench, so as to make the tire screws and tools fit more tightly, and it is easier to remove the tire screws.

It was an old car from before.

There are anti-buckles.

Today's trucks use positive screws.

The principle is that the inside is reversed and the outside is positive.

The screws of the inertia action in the direction of the tire will be loose.

Now the screws are tightened with an air wrench.

So the buckle screws are generally eliminated now.

Cars generally use semi-floating half shafts, the screws on the tires of the car are inverted, so that they will not be loosened when running, if the more they run tighter, the vibration at high speed will be large, which will cause the bolts to break, the tires will fly out, the consequences will be very serious, the tire screws are important fasteners in the car, the tightness and fastening sequence of the important fasteners are very strict, can not be too tight, can not be too loose, otherwise it will become a serious hidden danger that threatens safety.

Car tire screws do get tighter and tighter :

1. However, if the tire screw runs tighter and tighter, and the vibration is large at high speed, it will cause the bolt to break and the tire to fly out, and the consequences will be very serious;

2. Tire screws are important fasteners of the car, and the tightness and tightening sequence of important fasteners are very strict;

3. The tire screws should not be too tight or too loose, otherwise it will cause potential safety hazards.

The car tire screws are tightened clockwise, and they will not run loose, and if they will run loose, it should not be tightened in the first place. When the tire screws are not tightened, it is mainly manifested as a clicking sound in the process of driving, or the direction trembles, and in serious cases, the tires will shake during the driving process, resulting in the car running off.

The way to check whether the tire screws are not tightened is to use the vehicle's own hub wrench to try to see if it can be screwed, if the tire screws can be twisted effortlessly, it means that the tire screws are not tightened. The tire should be tightened in time, that is, it can be tightened to the tightest with a wrench, do not use foot or weight afterburner, if the tire screw is too tight, it will cause damage to the screw, and it will be more troublesome in the next disassembly.

However, in the process of daily use, the car tire screws will not run loose, but will only get tighter and tighter, and if the tire screws are loosened visually, then it means that the screws have been seriously loosened, and they are on the edge of falling, which will make the car drive with potential safety hazards. If you forget to tighten more than two screws when replacing a tire, the screws of the tire will slowly loosen, which is very dangerous and should be tightened in time.

Therefore, in the process of daily car use, it is very important to regularly check the status of the vehicle, such as: spare tire pressure, hub screws, tire pressure, tire deformation, etc., and should be dealt with in time when problems are found. In addition, it should be noted that if you go to the repair shop to perform operations such as exchanging front and rear tires, you must carefully check whether the tire screws are tightened.