What are the steps to use the lights correctly?

1. If you are about to turn at the intersection, please use the correct lights (alternate high and low beams no less than 2 times).

2. If you are about to pass through a sharp bend, please use the correct lights (alternate high and low beams no less than 2 times).

3. If you are going to cross the arch bridge, please use the correct lights (alternate high and low beams no less than 2 times).

4. If you are going to pass through an intersection that is not controlled by a traffic light, please use the correct lights (alternate high and low beams no less than 2 times).

5. If you are going to meet other vehicles, please use the correct lights (turn on the low beams).

6. If you are driving on a low-visibility road, please use the correct lights (turn on the high beams).

7. If you are about to pass through the slope, please use the correct lights (alternate high and low beams no less than 2 times).

8. If you are going to cross a pedestrian crossing, please use the correct lights (alternate high and low beams no less than 2 times).

9. If you are about to overtake, please use the correct lights (turn on the left turn signal first, then alternately use the high and low beams no less than 2 times, and then turn on the right turn signal).

Note: At the end of the light test, there is the following voice prompt: "Mock night test is completed, please turn off all lights" (when hearing this voice prompt, turn off all light switches within 5 seconds) must be turned off, not off 100 points, you must pay more attention to this.

Today explain the correct use of lights, take a closer look!

The use and operation of car lights are as follows:

1. Headlights. Most cars have high beams and low beams on the left rear of the steering wheel, and some cars are on the left side of the dashboard. There will be three gears in the front, middle and back of the lever, which represent the high beam continuous on, low beam, and single high beam, and only need to adjust the gear to the corresponding position to be able to light up the required light.

2. Fog lamp. The front fog lights and rear fog lights can be found in fog, snow, rain and other environments with low visibility, so that the rear vehicle lights can find themselves. Generally, the switch of the front fog lamp and rear fog lamp is on the light knob on the left side of the steering wheel or on the joystick.

3. Double flashing lights.

The red triangle button on the instrument panel is the double flash switch, which can be turned on when pressed. The function of the double flashing lights is to arouse the vigilance of other vehicles when the vehicle has an accident to prevent a rear-end accident.

4. a wide indicator lamp.

The car width indicator light is the front position light and the rear position light of the car, the width indicator light and the marker light are almost the same, and the different models will lead to the different installation position of the width indicator light. The width indicator lights on ordinary cars are usually called small lights, while the volume of large vehicles is relatively large, the lights on the front and rear sides are called width indicators, and the width indicators on trucks are usually called side lights.

5. Turn signal.

On the turn signal means to turn on the right turn signal, and under the turn signal means to turn on the left turn signal. The turn signal is an important indicator used by the car to alert the attention of surrounding vehicles and pedestrians when turning.

The position of the turn signal is installed on the left and right sides of the front and rear ends of the body, and it will provide protection for driving safety when the car turns.

<><1. Position light.

The location light source bureau is also called the wide indicator light and the running light. Turning on this light in the rain, when it is dark, or in an underground car park can make the four corners of the vehicle visible and avoid danger. It should be noted that the width indicator light is not as bright as the headlight, and it cannot be used instead of the low beam to drive in the dark.

2. Low beam.

The low beam has an irradiation distance of about 30-40 meters, which is suitable for use when there are street lights in the city at night. According to the requirements, the headlights are turned on along with the street lights, i.e. when the street lights are turned on, the low beams must be turned on. In addition, it is important to control the speed of the vehicle when driving at night to avoid danger due to poor vision.

3. High beams.

High beams can be used at night when driving in the wilderness or on unlit highways, but switch back to low beams when meeting traffic. The high beam light line is strong, which can shine up to 150 meters away, which will cause the opposite driver to have a blind spot in his vision, unable to see the road clearly, and it is easy to cause traffic accidents.

4. Fog lamp. Fog lights, generally used in foggy days, it is extremely penetrating under extreme conditions, the most critical role is to remind others of their own existence, only fog, rain, snow, dust, hail and other low visibility meteorological conditions, can be turned on. It should be emphasized that in the case of good visibility, the use of fog lights is not allowed, because the fog lights are too penetrating and will be very dazzling when opened, which is easy to affect the safety of pedestrians and cause traffic accidents.

5. Double flashing lights.

Twin flashing lights, i.e. hazard warning flashing lights, are used to remind nearby cars not to approach. Double flashing lights can not be used at will, according to traffic management regulations, the following situations can be used double flashing lights:

1) When driving in road conditions with visibility less than 100 meters;

2) When the vehicle breaks down on the road or has a traffic accident;

3) When towing a faulty motor vehicle, the towing vehicle and the towed vehicle should turn on the double flashing lights at the same time;

4) When making a temporary stop on a road or highway.

In addition, double flashing lights should also be turned on when applying sudden braking, especially on the highway, to avoid rear-end collisions to the greatest extent.

6. Turn signal.

When turning, merging, starting, and stopping, it is the basic principle of safe driving to turn on the turn signal in advance. Traffic laws stipulate that motor vehicles should use turn signals as follows:

1) When turning left, changing lanes to the left, preparing to overtake, leaving the parking place or making a U-turn, the left turn signal should be turned on in advance;

2) Turn on the right turn signal in advance when turning right, changing lanes to the right, returning to the original lane after overtaking, and stopping on the side of the road;

3) When a motor vehicle enters the highway from a ramp, the left turn signal should be turned on and the motor vehicle already in the highway should be driven into the lane without hindering the normal driving of the motor vehicle already on the highway.

Here's how to operate the lights for novices:

1. Turn the left light control switch twice to turn it into a low beam, which is mainly used for night city driving.

2. Screw the left light control switch forward for a small light, also known as the corridor light, which can be turned on when it is about to get dark, one can show the width of the car, and the other is to display the dashboard, which is easy to operate.

3. Push the light control lever forward, for the high beam, for the night outside the city road use, when there is a vehicle in the opposite direction, should be 150 meters away from the low beam light, to prevent the light dazzling the other party's eyes and accidents.

4. Lift the light control lever forward and up for the right turn signal, and push it down to the left for the left turn signal, which is used to change the direction, and will automatically return when the front of the car turns positive.

5. The use of near and far sprinkler lights is to pull the light control lever back (quickly release it after pulling), and the low and high beams can be changed, which has two main purposes. First, when driving outside the city at night, remind the other party to come to the car, pay attention to driving according to the road, and do not occupy the road; The second is to remind the vehicle in front of you to prepare to overtake when overtaking, and the vehicle in front will give you the car, which is used to remind the vehicle on the opposite side of the curve when entering the curve that there is a car about to turn.

6. In the middle of the instrument panel and the passenger station, there are two light control switches. One is the fog lamp, which is used when driving in foggy weather. The other is a hazard signal, when turned on, four turn signals flash at the same time, which is used when entering dangerous areas or when driving is inconvenient in special weather, and is used to remind the other party to keep a safe distance and avoid overtaking.

Sometimes the convoy will turn on this light on the road.

The precautions for the use of car lights are:

1. Turn on the low beam when driving at night; When the rear vehicle driving in the same direction and the front vehicle are driving in close proximity, the high beam shall not be used;

2. When passing through sharp bends, slopes, arch bridges, pedestrian crossings or intersections without traffic signal control at night, the high and low beams should be used alternately.

<> "When driving a vehicle at night, the low beam is normally turned on. If the environment is dark and there is no lighting, the high beams can be turned on at this time, because the high beams will shine at a higher angle than the low beams, and you can see the early stupid objects a little farther away, so as to ensure that the vehicle can drive safely.

In the process of driving at night, if Lu Xixiang encounters a vehicle coming from the opposite direction, he needs to turn on the car's low beam when the distance between the two cars is less than 150 meters. Remember not to use high beams, because the far land Zen lights will affect the vision of the other car owner, which is more likely to cause traffic accidents.

If you are driving at night and passing through an intersection where there is no signal, or if you are making a turn, we should use the near and far lights alternately, so that we can alert other vehicles.

If it is raining, snowing and foggy, we need to turn on the front and rear fog lights on the car, and the width indicator lights also need to be turned on.

If your vision is not good at night, you should slow down your speed. On highways, there are generally no street lights, so they are all lit by car lights. At this time, it is necessary to remember the essentials of using lights at night, turn on night lights, wide indicator lights, and fog lights in case of rain, snow and fog.

If there is no car ahead, you can turn on the high beams appropriately.

Simply use the high beams to briefly observe the road surface and surrounding conditions in the distance ahead, and then turn on the low beams. If there is a car in front of you or an oncoming car on the opposite side, you must remember to change the high beam to low beam, otherwise you will dazzle the eyes of the driver in front or on the opposite side, which will not only be annoying, but also easy to affect yourself in the event of an accident.

Hello, car lights are generally used in places with poor visibility, such as at night.

Car lights are generally used at night or in foggy weather.