ROUTER SPEED THROTTLING ISSUE

You see'Internet speed is limited"Did you see these 4 words somewhere?

What kind of company are you so rich to open a 100 trillion DSL Internet access that costs more than 5,000 a month for Internet access.

It seems that you are mistaken: your local connection is automatically obtained IP and it may be that your local connection is restricted.

It's not that it's a speed limit, no one is going to limit your speed.

Your broadband service provider is China Telecom Netcom Tietong Unicom Which one of the mobile is the Internet speed is so bad.

If it falls to 1-3kb, then it looks like a masterpiece of Tietong.

This is a problem with the transmission medium or the port in the computer room, and call the service provider to fix it.

Correct what you said about 100mbps

It's not the speed of your DSL broadband, it's the requirement that your network card can play fast LAN (Fast Ethernet), which means that if you have two computers at home, you can go from copying things to 100Mbps when you can get one through the LAN

10MB was the former normal LAN (Ethernet).

100MB is Fast LAN (Ethernet).

1GB is Gigabit LAN (Ethernet).

The difference between them is determined by the technology of the network card itself.

How to remove wifi speed restrictions on your wireless router:

1.The system is connected to a WiFi network.

2.Open a computer browser and enter the gateway IP address of the nameplate on the back of the router (generally, enter the gateway configuration interface.

3.Go to the bandwidth control settings interface in the router advanced, uncheck the enable buttons for all bandwidth control items, save it, or directly uncheck the bandwidth control function.

The router can bind your MAC address, or IP address, and then limit the speed, you can try to modify the MAC address, and IP address, but if the router is set to this speed as long as the route is routed, it is useless for you to modify anything, unless you can log in to the router to modify the configuration.

Unless you know the password of your router and undo the speed limit for your computer's MAC address, there's no other good way.

In my opinion, this has nothing to do with router settings, mainly looking around your computer system problems, you often surf the Internet, there are too many junk files in IE cache and memory, etc., haohao cleans up the following, you can use system optimization software to optimize, delete useless files.

Let's take a look at your company's network soundness.

If it's not very sound, it's generally with the help of third-party software to limit the network speed.

You first check what software you use, and then look for cracks on the Internet.

2 options.

1: You restore the router and the next exit settings are OK!

2: Have a good relationship with your company's network administrator, and secretly ask him to increase the speed! I'm in our company, and I do it all, and the internet speed is super good!

So can you get into the router?

Generally, the method of entering the router is to hit 192 on the browser,After entering, the chapter number password is admin,Then you go in to adjust the building,Some cats are not the same,You can look at the cat's platter or the product of the land game machine is looking for it,You can go in,Generally speaking,The network element has nothing to do with the land gamer,You also have to see if your door network is at normal speed,If not, it's not an early Netcom company。

You can use Thunderbolt's system optimization tool to change the number of connections to more than 200, if the speed has not changed, then you can only listen to the company.

Generally, the route binding IP is in the way of MAC+IP, and changing the MAC will not affect your LAN access, but it will have an impact on your routing binding authentication.

The company has made restrictions, which belongs to the content of personnel management.

Or open your own line

This situation indicates that the router is not dialing the Internet, and the possible reasons are as follows:

1. The router network parameters are set incorrectly, which may be due to the wrong input of the Internet account and password, and the operator's central office equipment cannot be dialed, so the Internet cannot be accessed;

2. The router network parameters are set incorrectly, it may be that the connection mode is set to manual connection or scheduled connection, and the router does not dial in at the current time, so it cannot access the Internet;

3. The ISP operator's central office equipment is faulty and the Internet is temporarily unable to access the Internet;

4. There is a problem with the line between the cat and the local equipment, and the central equipment cannot be dialed, so it is naturally impossible to connect to the Internet;

5. The router is connected incorrectly, the correct connection method should be to connect the network cable from the cat to the WAN port of the router, and then use a network cable to connect the computer with a certain LAN port of the router, as shown in the following figure:

If the interface is wrong, you will not be able to dial in to the network.

1. Use the wired function of the router, and the wired function of the router is generally more than 100m.

2. If the router is 11m, then it is small, and it must be at least 54m or more to get high speed.

3. If the speed limit is in the router settings, reset the router and use it in the settings.

4. Buy a new router.

This Gigabit router can only be described as a high-performance router with a system throughput of several gigabits per second or higher.

It's not that you can get that fast with a gigabit router, it's just that the routing is faster.

The speed of the 8-core network line is definitely not up to gigabit, but it is also very high, mainly because the hard disk is the bottleneck, just like the difference between a supercar and an ordinary sedan in the city, although the supercar can drive 320 yards, but it is actually 80 yards.

Prerequisites, 8-core Category 6 network cable, Gigabit switch, Gigabit network card, Gigabit crimping method, suitable for internal LAN,

There is no point, there is no point at all. For example, if you buy 10M broadband, you buy a 1000M router, do you think there will be 1000M?

Haha、The result is obviously no、。 The most is the amount of broadband you buy.

Many routers have this function, in the router settings, that is, in the default gateway, directly limit the IP traffic.

If there is no speed limit, the stand-alone machine is normal, you first see if it is rubbed against the network, if not, it is a quality problem with your router, do you want to change it, or you flash the firmware to see if it can be solved.

The easiest way to do this is to restart your router.

Enter the routing management interface (enter the router IP point enter in the browser address bar, and then enter the account password, there is a mark under the route) to cancel the bandwidth control function, but it is not necessarily caused by this reason.

You take a look at how much bandwidth your router has, if the bandwidth is really small, the network speed is not good, it is recommended to change the router.

If it's 150M or higher, you can go to the router and check your settings, and see if there is a speed limit in the IP bandwidth control option.

First, you need to bind the IP of the specified client to the MAC1, open the browser, enter the router box or the manual written on the manual) Enter the router account and password.

2. Click [Static ARP Binding Settings] under [IP and MAC Binding] to confirm that the ARP binding on the right is enabled, and then click [Add Single Entry].

3. Check the binding;

Click Save.

2. Then limit the rate of the client IP.

1. Click [IP Bandwidth Control] on the left and check [Enable IP Bandwidth Control];

Please select your broadband line type: select ADSL line;

Please fill in the bandwidth size you requested: enter the bandwidth provided by the network provider;

Then click Save.

Mode: Select Limit maximum bandwidth;

Bandwidth size: Enter the limit bandwidth;

Confirm that Enable is checked;

Then click Save.

Log in to the router parameter settings page, and cancel the rate limit in device management.