How the Mercury Wireless Router 300R limits the speed of wireless Internet access

Ordinary routing and software do not have much effect even if the speed is limited, the key is to solve the main application under a variety of applications is not affected, so you had better change to an intelligent QoS route, although the ordinary route can limit the speed, but can not guarantee the delay of the game, the browsing of the web page, because to do**game web browsing does not interfere with each other, simple speed limiting is not enough, but also to set up a guarantee bandwidth, limit the maximum number of connections, turn on burst traffic, set priority, set the game port priority, turn on small packet sending** Priority and so on. Generally, these functions can only be achieved by intelligent QoS routing. It is recommended that you buy an intelligent QoS behavior management route, and you can even directly block others from watching**,**etc.

Log in to the router and set up broadband on the left sidebar.

It's better to be happy alone than to be happy, there is wireless wifi at home, and my friends are coming to my house more and more times, of course, good things have to be shared! I have collected the Mercury 300 wireless router settings, welcome to read.

1.First of all, the power supply of the wireless router is connected, and the operator's network cable is plugged into the WAN port (generally if it is not a mini router, it is usually 1 WAN port and 4 LAN ports), and generally except for the telecom may also need a modem (modem) to convert the ** line into a network cable, other operators can be directly plugged into the WAN port of the router.

2.Since it's wireless, of course, you don't need a network cable to connect, you can check it in the network sharing center (my system is win7); After the new route is connected, it will remind you that this router needs to be configured, whether it is configured, and you need to press the WPS on the wireless router to configure it for the first time according to the prompts, because this router has been configured, and this step can no longer be presented to you. ps:

Even if this step is not configured, it does not matter, what matters is the configuration after the connection route.

Enter in the browser address bar: The first time you visit, the router will prompt you to set a password, and it takes more than 6 digits, admin is only five digits, so you can't use this password, think of one by yourself, but not too long, if you forget it, you have to reset the route.

4.After still connecting to the wireless router, log in to the router, such as the setup wizard, select PPPOE dial-up Internet access, the general operator will provide a dial-up Internet account and password, generally except for the campus network user, the home network user is basically ADSL virtual dial-up.

5.Enter the account name and password provided by the operator, but the password needs to be entered twice.

6.Set the SSID, which is your wireless network name, you can take a high-end atmospheric and high-grade name, but it seems that Chinese is not supported! Dear, remember to turn on wireless security, otherwise your wireless anyone can rub the network, the input box is the password you set for the wireless router, if you want to connect, you must verify the password!

You're basically done with the wizard setup.

Port settings, the connection mode can be set under the general settings, select automatic connection (automatic reconnection after disconnection and restart, WAN port rate, select automatic negotiation, the difference between half-duplex and full-duplex is that half-duplex sending and receiving are mutually exclusive, and full-duplex can be received or sent (at the same time).

Port settings, wireless routing, persuade everyone to modify the access address, I am afraid that some people mistakenly modify the settings, you must know that wireless can be different from wired, wired must be connected to the route with a network cable, wireless as long as people connect to your wireless network, your routing access address is still there, although there is still a layer of password verification, but not afraid of 10,000 in case, we will directly let him access the address do not know!

Subnet mask. Subnet mask.

Subnet mask.

Material: Mercury router, computer hidden wax.

1. Enter :" in the browser, and enter the login username and password in the pop-up dialog box to log in. (The default username and password are: admin, if the user has changed the default account and password, the changed one shall prevail).

2. Click "DHCP Server" -- continue to click "DHCP Service" -- record the "Address Pool Start Address" and "Address Pool End Address" in the interface on the right, which will be used in the later setting process.

3. Click on the "IP Broadband Control" option in the management interface--- check "Enable IP Broadband Control" in the pop-up dialog box on the right side - select ADSL behind the "Broadband Line Type--- fill in 4096Kbps (1M Broadband = 1024Kbps, the user calculates and fills in according to his total bandwidth) and click "Save" - and then click "Add New Entry" option.

4. Check "Enable" -- fill in the "Address Pool Start Address" and "Address Pool End Address" under the "DHCP Service" recorded in the second part after the "Start Address" and "End Address" options -- Set "Uplink Broadband" and "Downlink Broadband" below the "Maximum Bandwidth" column (in fact, the uploaded data and ** data are the maximum bandwidth allowed to be used) Fill in 1024 (assuming that the computer in the LAN is allowed to use 1M broadband, Users please set it according to their needs) - click "Save".

5. Under the "IP Broadband Control" option, you can see that the speed limit entry you just set has taken effect.

Here's how to set the Mercury MW300R router to limit the internet speed:

1. Enter the router management interface, log in, and enter the username and password (the default is admin admin);

2. Select IP bandwidth control in the left menu bar;

3. Click Add New Entry;

4. Enter the corresponding IP address and set the uplink and downlink bandwidth;

5. Click Enable, click to enable IP bandwidth control, save and exit;

6. Restart the router to take effect;

As mentioned above, it should be noted that the total uplink bandwidth is set to the corresponding total uplink and downlink bandwidth, the total uplink bandwidth is about 1 8 of broadband (such as telecom 8M), and the uplink bandwidth of civil broadband is 1 4 of the downlink.

Related References:

This page is the speed limit.,Like the one upstairs said.,Fill in the total bandwidth of your network cable on top.,And then add the IP segment and the speed you want to limit below.。

The top one is total, i.e. set according to your wide band. It can be set to a little larger.

Then you can add the IP address below in the "Add New Entry".

Hey, I also bought one, it seems that the speed limit can't be reached, depressed, when I went to ** asked the seller, they said that this one can't be speed limited, and the functions inside are just decorations!

Here's how to limit the wide speed speed of the Mercury MW300R router:

1. The default management address of Mercury router is, enter the IP address of the router on the Internet Explorer, then enter the username and password of the router, and click the "OK" button.

2. After entering the router management page, click "IP Bandwidth Control" in the list on the left side of the page, and then check the "Enable IP Bandwidth Control" option on the right.

3. Then select the type of our broadband, here I choose the broadband type as ADSL, and the bandwidth size is 2000 kbps.

Note: Please enter the bandwidth size according to your actual situation, the default value is 2000kbps

4. Next, configure the IP bandwidth control rule

1.The rules are controlled by IP address ranges, for example, if you enter 100-150 here, this means that these IP addresses will be controlled by this rate limiting rule.

2.Select Limit Maximum Bandwidth as the mode and select Enable.

3.The bandwidth size is set to 100 kbps, which means that the maximum speed cannot exceed 100 kbps. Please set it according to your actual situation, if the speed limit effect is not ideal, you can adjust this value slowly. After the adjustment, click Save.

In the bandwidth control.

How to set the wireless speed on the wireless router: only the speed can be limited.

How to limit the speed of the router].

2. Enter the correct username and password to enter the router management background.

3. Check the existing IP address and the corresponding MAC address bar first. Click "DHCP Server" on the left, select "Client List", and write down the corresponding IP and MAC addresses displayed on the right.

5. Enter the correct corresponding MAC and IP address on the right, then select "Status" as "Effective", and then click the "Save" button to save.

6. Repeat the previous two steps until all IPs are added.

7. Click the "IP Bandwidth Control" link on the left, check the "Enable IP Bandwidth Control" checkbox on the right, and select the correct network speed below.

8. Then fill in the IP and bandwidth size to be controlled in the following rules, and also set your own computer "Guarantee minimum bandwidth", and select "Enable" for all, and then click the "Save" button to save all the settings.

The speed of the wireless network does not need to be set by default, and the strength of the wireless signal received by the computer depends on the distance between your computer and the wireless router. I don't think it's set.

Line connection router and setup steps:

1. Connect the line between the network cable, the router and the computer, and start the computer and the router equipment;

2. Look through the nameplate or instruction manual at the bottom of the router to find the router IP, default account and password. If the access is optical fiber, the IP address of the fiber modem must not be in the same network segment as the router IP address, otherwise it is easy to conflict.

3. Open the browser, enter the IP address and press enter, if the input prompt is incorrect, it means that it has been modified, you can only press and hold the reset button on the router to restore the router to factory settings and reset it;

4. Enter the router login interface, enter the default login account and password queried, if the input prompt is incorrect, it means that it has been modified, and can only be reset after resetting the router by pressing and holding the reset button on the router;

5. Enter the router settings interface, find the setup wizard on the left menu bar, select Next according to the prompts, and select PPPoE dial-up Internet access;

6. Enter the password applied for from the network service provider, and go directly to the next step after the input is completed;

7. Set the wifi password, try to make the alphanumeric combination more complicated and not easy to be rubbed off the network (this step is for the router with wifi function, and without wifi function, go directly to the next step);

8. After entering correctly, it will prompt whether to restart the router, select Yes to confirm the restart of the router, and you can access the Internet normally after restarting the router.

Look at the IP address on the back of the router, enter it in the browser, and then fill in the password or ask you to change the password, after entering, select PPPoe in the WAN port parameters, set your broadband password, select automatic connection, and save. Then set the wifi password in the wireless parameters.

The jumper is connected to the computer at one end and the router at the other end, the broadband is connected to the router yellow port, the power supply is connected, enter the press enter password and account in the browser address bar, and follow the steps after entering, and select PPPOE for connection mode

1. To limit other people's network speed, you must first log in to the router and enter the bind MAC option to bind the MAC address.

2. Remember the MAC address (someone else's address) IP that needs to be bound, and then enter the bandwidth control option, and limit the speed for the IP address of someone else who has been bound.

By entering the router's settings page, you can see that there is an IP bandwidth control in the settings page, just in there, the easiest way is to update 360 to the latest version, there is a router guard inside, and you can directly limit the speed inside.

Connect the LAN port of the router to the WAN port, the broadband cable of the computer plug.

The IP of the local connection of the computer is set to be obtained automatically, then open the browser, enter in the address bar, the username and password are admin, and enter the router setup wizard.

Then prompt to enter the account password (ADSL) broadband IP address (if your broadband is a static IP), dynamic IP does not lose.

Finally, set the wireless password to prevent others from surfing the network, and save the settings to restart the router and the installation is complete.

Connect the home bus cable to the wireless router, take a network cable from the wireless router to the computer, and press enter on the browser of the computer to browse the Internet to enter the router's settings. Or hit Enter. Find the manual of the router and look at the username and password to enter the router, usually the username and password are admin.

After entering, you can set it to only use 2 devices, one is the wired connection of your computer, and the second is your wireless device such as a mobile phone or pad, I hope it can help you!