Electric water heaters are getting colder the more you use them

You can't turn off the water filling, so you won't be able to get water, and you can't wash it dry (and you can't wash it). The more you wash, the colder it is because the heating speed of the water cannot keep up with the heat of the outflow rate, you can only adjust the amount of water output to a smaller amount, when the heating energy is equal to the energy consumed by the water, the water can be kept at a constant temperature.

You can't turn off the cold water, the principle of the electric water heater determines that if you don't put in the cold water, you can't release the hot water.

In fact, a 50L water heater can fully supply two people with a bath. You can set the water temperature higher. Generally, the maximum temperature of the electric water heater is set at about 75 degrees, and it is no problem to take a bath with 75 degrees of water mixed with cold water.

No, because if the water inlet switch is turned off, there will be no water in the outlet, and the temperature can be turned up.

The reasons for the cooling of the water may be:

1. The water pressure is unstable, caused by cold and heat;

2. The temperature control display is faulty, resulting in the display failure, or the hot water cannot meet the standard, and the display is wrong;

3. The control valve fails, and the cold water valve is on the water, causing the hot water to be combined, and when the water temperature is lower than the body temperature, the water is cold;

4. The aging of the insulation layer, when the insulation material of the water heater does not meet the use standard, it happens to meet the low ambient temperature, and the hot water temperature drops quickly, which is also one of the reasons.

The heat dissipation itself is fast, the temperature of the tap water entering is very low, the electric water heater is still energized for a long time, the temperature control probe of the water heater Chayu is in the middle of the water heater, and only the water temperature of the upper half of the water heater is hot when it is just heated to the set temperature, and the water temperature of the lower half is not hot.

The inner tank is the core component of the water heater, which directly affects the safety performance, performance and working life of the water heater. When choosing a water heater, users should be concerned about whether the material of the inner liner steel plate of the water heater is titanium alloy, whether the thickness is thick enough, whether the welding process is advanced and reliable, whether the quality of the enamel glaze is guaranteed, and whether the enamel sintering process is advanced.

Summary. First, the water pressure in the cold water pipe is too large, which causes the water in your inner tank to mix too quickly, destroying the stratification of hot and cold water.

Second, the water temperature probe of the water heater is positioned upward. Hot and cold water is stratified by detecting the temperature of the upper layer of hot water, not the temperature of the middle or bottom of the tank. In fact, the hot water in the inner tank of your water heater is not as hot as it is displayed.

Third, the volume of the electric water heater is too small, and the water output of the sprinkler head is too fast. As a result, the hot water quickly ran out.

Fourth, there is a problem with the mixing valve.

Fifth, there is a problem with the thermostat.

What's the matter with the water heater heating slowly and cooling fast.

Hello, I have seen your question and am sorting out the answer, please wait a while

Hello pro-Sou Wu Zhao, glad for your question. <>

1. There is too much scale in the heating pipe of the water heater, which causes the heat inside the heating pipe to be unable to dissipate quickly, resulting in slow heating of the water heater. 2. Thermostat failure, if the thermostat of the water heater is faulty and the thermostat of the water heater fails, then the temperature of the water heater may not reach the normal set temperature and automatically stop heating, resulting in slow heating of the water heater or higher than the user's set temperature, or even continuous heating. This can be dangerous.

Professionals are required to rent a home to inspect and repair. In addition, a faulty thermostat can cause the water heater to not heat up.

Did the water hook of my home appliance water heater be blocked after less than three years of use.

The water heater heats up slowly and can be added to the set temperature, but it cools very quickly.

First, the water pressure of the cold water pipe is too large, which causes the water in your inner tank to mix too quickly, destroying the stratification of cold and hot water. Second, the water temperature probe of the water heater is positioned upward. Hot and cold water is stratified by detecting the temperature of the upper layer of hot water, not the temperature of the middle or bottom of the tank.

In fact, the hot water in the inner tank of your water heater is not as hot as it is displayed. Third, the volume of the electric water heater is too small, and the water output of the sprinkler head is too fast. Yu Jipai did not have a clear argument that the hot water quickly ran out.

Fourth, there is a problem with the mixing valve. Fifth, there is a problem with the thermostat.

Life is not easy, and the evaluation of my relatives is very important to me <>

If this answer is helpful to you, you can ask for a consultation with the five little stars, please click on the five little stars <>

<> thank you very much!

Storage type electric water heaters, the water consumption is greater than the storage water, there will be this small disadvantage. Because the water is mixed with hot water (heated in the tank) and cold water (tap water) at the same time, and the cold water is injected into the tank, of course, it will get cooler and cooler.

The correct way to use the storage type electric water heater is as follows: the storage water heater is heated to the required temperature first, and the water inlet valve of the water heater is turned off when used, so that no cold water will be added, and the water will not get colder and colder.

Summary. Solution: Buy a large model water heater and open the hot water valve wide when the hot water is cool. You can also install a heater at the cool water pipe of the water heater to raise the temperature of the tap water entering the water heater.

Dear, hello, the storage type electric water heater Xuye is relying on tap water into the hot water such as the land, the inner tank water is filled and begins to heat, the maximum temperature is about 80 degrees, and the bath residue Yuqing uses the pressure of tap water to push out the hot water of the inner tank. When cold water and hot water are mixed, the temperature of the hot water in the inner tank will quickly decrease, and when it reaches below 40 degrees, the human body will feel cooler and cooler the more you wash, which is especially obvious in winter.

Solution: Buy a large sail hail water heater, and open the hot water valve when the hot water is cool. You can also install a heater at the cool water pipe of the water heater to increase the temperature at which the self-cracking water enters the water heater. State of the big sails.

The rapid drop of water spoilage temperature is related to the capacity of the water heater, and the smaller the capacity, the faster the cooling. The water temperature drops too quickly and is related to the temperature of the incoming water, and the lower the water temperature, the faster the cooling will be. The water temperature drops too fast and is related to the power of the water heater, and the smaller the power, the faster the cooling.

The rapid drop in water temperature is related to the shower in the shower, and the higher the flow, the faster the cooling. The water temperature drops too quickly and is related to the length of the pipe, and the longer the pipe, the faster it falls.

Solution: 1. Use the method to judge the insulation of the water heater, that is, you boil the water temperature to 100 degrees, and then turn off the power, if the cooling does not exceed 2 4 degrees in an hour, then the water tank insulation is no problem.

2. If you don't use water, the water temperature will be heated to more than 80 degrees in 1 2 hours, and the heating is basically no problem.

If the above two points are fine, and the water temperature drops quickly, it is the reason for use. First, the water consumption is too large, and the stored water will be used up at once, so the water needs to be adjusted a little smaller. The second is that the temperature of water heating before using water is not high enough, because the normal water is mixed with hot water and cold water to a certain water temperature to use, if the hot water temperature is high, the cold water is more and the amount of hot water is less, the hot water will be used for a long time, on the contrary, the hot water temperature is low, and the hot water is not durable.

Generally, hot water is heated to about 90 degrees Celsius before use.

Hope mine can help you.