How to use the clone disk system, how to install the clone system, the clone version of the system i

How do I install the clone version of the system? The cloning system is the ghost system, an operating system made by the ghost packaging tool, and the biggest advantage of the cloning system is that it is quick to install and automatically activated, so it attracts users to install and use. Although the installation of the cloning system is very simple, there are still some users who do not know how to install it, and the following takes the installation of the deep ghostwin7 system as an example to introduce the steps of cloning and installing the system.

Instructions:

2. It is recommended to install a 32-bit system with 2G and below computer memory, and a 64-bit system with 4G and above memory.

How to install Win7Ghost on a USB flash drive

The solution to the problem that the USB flash disk system cannot put more than 4G images.

When installing the system, it prompts you that you have not specified the ghost32 ghost64 location.

1. Preparation for installation

1. Back up important files on the C drive and desktop.

4. Decompression tool: winrar or good pressure and other decompression software.

2. The steps to install the clone system are as follows:

2. Put the file and OneKeyGhost tool in the same directory, such as D drive, do not put C drive or desktop;

3. Double-click to open the OneKeyGhost installation tool, select "Restore Partition", select the file for the ghowimiso image path, select the installation location, such as C disk, or orange segment according to the disk capacity to judge the disk to install the system, click OK, if the ghost location is not specified, check the method provided by the relevant tutorial to solve;

4. A prompt box pops up, after confirming that there is no important data, click Yes, and immediately restart the computer for restoration, that is, the process of installing the system;

5. At this time, the computer restarts, and the boot startup item is more onekeyghost, and onekeyghost is automatically selected by default to enter the installation process;

6. Start to enter this interface, check the operation of installing the cloned version of the system to the C disk, and wait for the progress bar to be completed;

7. After the operation is completed, the computer will automatically restart, continue to perform the system driver installation, system configuration and activation process, and the system installation of the cloning system will be completed automatically;

8. There will be an automatic restart process during the installation process, and finally after rebooting into the new system desktop, the clone system installation will be completed.

The above is how to install the cloned system, the clone version of the system can be directly decompressed and installed, or it can be installed through a USB flash drive, and the installation is very simple.

Install XP and common software, and carefully set up and optimize it with ghost as a backup, and use this backup for the system in the future!

Back up your system with ghost! Here's how! Go to the ghost interface and select 1 2 2 and then back up the C drive!

Copy the image file to the boot disk.

Then use the startup disk to insert it into another computer, start it with a USB flash drive, select ghost, enter the ghost and manually select the recovery file to copy the image file to the USB flash drive, and then restore it.

However, it is important to note that if the configuration of the two computers is not exactly the same, if the system of the front computer is mirrored and then restored to the other computer, then the other computer may have problems such as blue screens. Therefore, it is recommended to install it directly with the installation image file on another computer.

Computer systems with different hardware configurations cannot clone each other, otherwise it is easy to cause a boot blue screen due to the difference in hardware drivers, and you can only install the original clone file on another computer.

Recover your system with ghost software:

1. Enter the PE system and open the ghost software, click "local", then select "partition", and finally select "from image".

2. Select the image file that needs to be recovered, and find the system image file you need (.)gho suffix file) and click Select.

3. Then select the source partition from the image file, since there is generally only one source partition, just click OK.

4. The next step is to choose which local disk to restore the selected image source partition to, if the general user only has one hard disk, then click OK to continue.

5. Select which partition to restore to, the general user installs the system C disk, that is, the partition with type as primary, if you are not sure, you can judge by the size (capacity), and click OK after selection.

6、ghost will start to perform the above operations,When the progress bar is finished, the ghost prompts that you need to restart,After the restart, it will continue to install the system automatically。

If there is no mistake in the burning process, it should be a problem with the disc, try a better disc.