VMware 5 5 5 VM Problem 50 points

This software is a very good software that can be used to virtualize multiple machines at the same time, especially for learning, research and experimentation, if your machine hardware is good enough, you can virtualize a complete network of multiple servers and clients.

The most common way to use it).

1. After launching the software, select Create Virtual Machine.

2. Next, go to the virtual machine configuration and select "Typical".

3. The next step is to "Virtual Machine Operating System" and the type of system you want to install first.

4. Next, enter the name of your virtual machine and the location of the virtual machine in your original system.

5. The next step is to select the network connection type of the virtual machine, which can be selected according to your needs, generally choose the bridge, at this time, the virtual machine needs a separate IP address, and you can treat it as another machine.

6. Next, select the disk capacity, and select it according to the situation.

7. Finally, select "Finish" on the right side of the "start page" on the software interface, and a virtual machine you name will appear.

8. Click on the virtual machine, and the virtual machine page appears. On the left is the command, and on the right is the device.

9. Click to start the virtual machine, just like you turn on the machine switch, put the disc in the optical drive, install the system, and then install it completely like a new machine. After the installation is complete, you need to set up the new virtual machine, such as printers, IP addresses, etc. If you want to share, you'll need to install the corresponding IPX protocol, which can be accessed from your online neighbors.

The key is to treat it as a new machine, but pay attention to using "Ctrl+Alt" to switch between the original machine and the virtual machine.

A few simple words, I don't know if it can meet your needs.

With the bridging method, you can access the Internet.

First of all, change the properties of the network card!

By sharing.

Frequently asked questions.

1. After creating a new virtual machine, "Unable to initialize easy install" appears. If the error persists, you may need to reinstall VMware Workstation. "Wrong.

Solution: When creating a new virtual machine, select I will install the operating system later (create a virtual blank hard disk).

2. When you click "Install VMware Tools" in the menu "Virtual Machine", "Easy Install is in progress, you can't manually start VMware Tools installation." "Wrong.

Solution: Set the "Connection" of the "Floppy Disk Drive" of the virtual machine to "Use Physical Drive", or cancel the "Connect when power on" of the "Device Status".

3. When starting the virtual machine system, "serial0: unable to launch virtual printer proxy: The system cannot find the specified file."

The device is about to be disconnected. "Wrong.

Method 1: 1. When you open the VM, an error message is displayed: "The physical memory is insufficient, and the configured settings cannot be used to start the VM."

To fix this, reduce the memory size of the virtual machine to **MB, increase the amount of physical memory used by all virtual machines to **MB, or adjust other memory settings to allow more virtual machine memory to be swapped.

Native applications and/or services may have memory locked, which will prevent the virtual machine from starting. Shutting down an unwanted application or service may free up enough memory to start this virtual machine. If you were previously able to turn on the virtual machine on this host, try rebooting the host.

After the host is rebooted, there may be slightly more host memory resources available to run the virtual machine than it is today. “

The workaround is as follows, and the following host environments for Windows, Win7 may also apply:

2. If the operating system version of the host is Windows or above, please upgrade the VMware Workstation to the version, this version solves the problem of physical memory identification error under . If the VM still does not start properly after the upgrade, you can try all of the following methods in turn.

Method 2: 1. Restart the computer and open VMware Workstation after the computer boots up to allow the virtual machine to enjoy enough physical memory.

Method 3: 1. Create a new virtual machine (any operating system) and start it, at this time, the new virtual machine can run normally, and the previously created virtual machine can also run normally.

Method 4: 1. In the menu of the virtual machine, select "Memory" in the left option.

2. Raise the host physical memory reserved by the system for the virtual machine to a "warning threshold", that is, when it is greater than this value, a warning will be prompted: the reserved memory is greater than the recommended maximum value for this system, which may reduce the system performance.

Method 5: 1. Modify the configuration parameter file of the virtual machine

C: documents and settings all users application data vmware vmware workstation or c: programdata vmware vmware workstation directory and set " = to"true"" = Change to a small enough number, such as "1".

2. Then increase the virtual memory of the system. Right-click on "Computer" and click on "Properties" and on the left side click on "Advanced System Settings". Select the Advanced tab Performance Settings button, and select the Advanced tab Change for Virtual Memory. Button.

3. Here you can set the size of the virtual memory paging file allocated to each hard disk partition, "no paging file" means that the virtual memory paging file is not allocated in the partition, and the size of the page file can be customized.

When creating a virtual machine, there is a place to select the memory size, or you can modify the memory size directly in the settings. I guess it's because you're setting it too big. You can take a screenshot and put it up.

Set the memory to a larger size when setting it. It is equivalent to two systems plus one virtual machine, and the physical memory is certainly not enough.

1 Short: The system starts normally. This is something we hear every day and it also shows that there is nothing wrong with the machine.

2 Short: General error, please go to CMOS setup and reset the incorrect option.

1 Long 1 Short: There is an error with the RAM or motherboard. Try to change the memory, if it still doesn't work, you have to change the motherboard.

1 Long 2 Short: Wrong monitor or graphics card.

1 Long 3 Short: Keyboard controller error. Check the motherboard.

1 Long 9 Short: Motherboard flash RAM or EPROM error, BIOS corruption. Try a different block of flash ram.

Constant ringing (long sound): The memory module is not plugged in tightly or damaged. If it still doesn't work, you can only replace a memory module.

Ringing: The power supply and monitor are not properly connected to the graphics card. Check all the plugs.

Repeated short rings: Power supply issues.

No sound, no display: Power issue.

The explanation downstairs is too detailed, this wealth is not easy to earn, haha.

1、The Chinese plug-in should be installed according to the version of VMware,Your VMware is 32-bit, install 32-bit。

2. After VMware is installed, in order to facilitate interaction with the host, a VMware user will be created, so when the host is turned on, it will stop at the user who selects the user, and this user can delete it, which will not have a great impact on the use of VMware.

3. It can be set to manual, and then start manually when it needs to be started.

4. Whether the virtual machine is supported depends on the specific technical information, and the prompt that pops up should not be installed if it is in the virtual machine system, and if it is a software prompt, it should not be supported. There is no question of whether the VM is supported, but whether the VM does.

Bit 2You take a screenshot I haven't encountered this situation.

The first four or five bars are OK as long as you don't turn off when you run the virtual machine4Go to the virtual machine settings and see if there is this option.