How to set 10 for TP WR720N

It is estimated that you have to buy a switch or a wireless network card, two desktops, no wireless network card, you must use network cables, and your router only has a wired socket, and the other is a broadband inlet port, so you either buy a switch for thirty or forty yuan, or equip one of the desktops with a wireless network card, if you use a switch, you need three network cables, one from the router to the switch, each computer is connected to the switch, and the switch does not need to be set up; If you buy a wireless network card, the cheap one is sixty or seventy, and a network cable goes from the router to the computer without a wireless network card, and the computer with a wireless network card is connected to the router through wireless like a mobile phone.

You can only use a switch, or buy a wireless network card, plug it into the desktop, and bridge it to the router.

The TP-Link TL-WR700N can be set up as follows

TP-Link TL-WR700N mini wireless router, there are currently 3 versions, namely V1, V2, V3; The v1 and v2 versions are completely the same in terms of settings, but v3 is different from v1 and v2 in terms of settings. So, before setting it up, check the version number of your TL-WR700N on the label at the bottom of the router.

<>3.First you need to enter the login password (there is a prompt on the back of the router), usually admin login.

4.The Setup Wizard will pop up by default, if it doesn't pop up, you can click the Setup Wizard on the right to set it.

5.Click on AP (Access Point Mode) to take a closer look at the application scope of the mode Next.

After the settings are completed, click Restart, the router will be automatically refreshed, and the settings will take effect.

7.Finally, plug the network cable into the router port and you're ready to enjoy Wi-Fi.

The installation and setup of the TPLink router is as follows:

3.Once you've logged in to your backend, select Quick Settings and click Next4Choose the way to access the Internet, usually ADSL users choose the first PPPoE, if you use other network service providers, then choose the following two according to the actual situation, if you don't know how to choose, directly select the first item to automatically select, convenient for novice operations, click next after selection;

5.Enter the account and password applied for from the network service provider, and go directly to the next step after entering.

6.Set the wifi password, try to make the alphanumeric combination more complicated, and it is not easy to be rubbed off the network.

7.After entering it correctly, it will prompt whether to restart the router, select Yes to confirm the restart of the router, and you can access the Internet normally after restarting the router.

When the network cable is connected to the router, we enter it in the browser address bar (this is the default login address of TL-WR710N, of course, some may be, some are, according to the brand and model of the router, you can refer to the manual), and then press enter, you can see that you want to enter the password, the default is admin

How to set up the TP-Link (WR710N) router.

When entering the password to enter the system, click the Setup Wizard on the left navigation, as shown in the figure below, and click Next.

How to set up the TP-Link (WR710N) router.

Go to the following page, select the second item - Wireless Routing Mode, and click Next.

How to set up the TP-Link (WR710N) router.

You can see that you need to set the name of the wifi, the default encryption type, and the psk password, that is, the password of the wifi, click next after entering.

How to set up the TP-Link (WR710N) router.

Because I am here under the switch display, look at the picture noted, if it is a separate adsl dial, just select it directly and enter your account password next, and then click Done, wait for 1 minute.

How to set up the TP-Link (WR710N) router.

6After clicking to complete it for a while, we click on the running status at the top left, look at the parameters and status, indicating that the router has been set up, the computer can access the Internet, and your mobile phone or tablet can also be connected to this wifi Internet access, hehe, simple, go and connect to the Internet.