The working principle of the automatic soymilk machine, 5

The soymilk machine is a new type of household beverage machine, which uses soybeans as raw materials to directly process mature hot soybean milk. If soybeans are mixed with sesame seeds, peanuts, almonds and other condiments, you can make delicious drinks of various flavors. The soymilk machine consists of three parts: a blender for crushing soybeans, a soymilk heater and a control circuit.

The control circuit of the automatic soymilk machine developed by the single-chip microcomputer, as long as the start button is pressed, the soymilk machine will start working, and you can drink delicious and nutritious soymilk in a while. The whole process is fully automatic controlled by the microcontroller, which makes it more convenient and safer for you to use.

Fully automatic control of the function of the soymilk machine:

1. Separate heating: It has the function of separate heating, and can stop heating at any time.

2. Separate crushing: with the function of separate crushing, the crushing is 15 seconds at a time, and it will not stop in the middle.

3. Automatic work: the process is as follows: in the presence of water, the electric heating pipe starts to heat, when the water temperature rises to 82, the heating stops, and the motor starts to work 4 times.

Then continue to heat, when the foam produced by the soybean milk touches the anti-overflow electrode, turn to power reduction heating, heat for 6 minutes, end and alarm.

4. The whole process is in the state of no water alarm and stop working: during the period of separate heating, separate crushing and automatic work, the soymilk machine will stop working and alarm at any time. When the soymilk maker is re-put into the water, it will return to its previous working state.

Power Reduction Heating: In the automatic working and separate heating mode, when the foam produced by the soybean milk hits the anti-spill electrode, it will be converted to power reduction heating.

5. Self-test mode: press the "heat" and "crush" buttons at the same time for more than 2 seconds to enter the self-test mode. The buzzer and indicator light chirp and flash 3 times at the same time, with an interval of seconds each time, then the indicator light is always on, heated for 1 second, the power is reduced for 1 second, and the motor works for 1 second, and then all stop.

The report mode is that the buzzer and indicator light are chirping and flashing at the same time, with an interval of 1 second each time.

If you do a physics problem, the answer is the latter!

Principle: Add water to the soymilk machine, the electric heating tube starts to heat, when the water temperature reaches 82, it will stop heating, and after the motor works for 4 consecutive times, it will continue to heat. At this time, when the foam produced by the soybean milk touches the anti-spill electrode during the flow process, it will automatically switch to the heating method of reducing power, and it will be heated for 6 minutes, and an alarm will be issued at the end of the process to show the completion of the work.

1. The general operation process of the soymilk machine is to soak the soybeans first, put the soaked soybeans into the soymilk machine, add water between the upper and lower water lines, and cover the lid. Then choose the operation mode - fast soymilk, start making soymilk, after stirring for 20 minutes, the general soymilk machine will send out a "drip" prompt sound, and the indicator light will also flash. Pour out the soy milk and add the sugar.

Stir and serve.

2. In addition, I remind you that you should wash it after use and keep it clean. Otherwise, it will leave an unpleasant smell in the soymilk maker, which will affect the effect of the next use. A certain amount of cleaning and maintenance can also better extend its service life.

In order to consider the durability of the crushed bean knife, the current manufacturers are first heated, beaten, reheated, and then beaten, because the pulp concentration is not enough at one time, and the taste is not good, so they all use the procedure of multiple crushing.

Prepare materials: water, soybeans, soymilk maker, loss strainer, kettle, cup.

1. First pour an appropriate amount of water into the soymilk machine.

2. After pouring the water, pour in an appropriate amount of soybeans, and pay attention to the soybeans without soaking.

3. After pouring the water and soybeans, cover the lid of the soymilk maker.

4. Turn on the power supply, slow sensitivity, and then select the pulping function.

5. After the soybean milk is ready, turn on the faucet of the soymilk machine and use the kettle to bring out the soy milk. Scrambled branches.

6. Strain the soy milk through a strainer.

7. Finally, pour the soy milk into a cup and enjoy.

(1) The basic characteristics of the soymilk machine circuit.

Generally, the fully automated processes such as preheating, beating, and boiling of soymilk machines are completed by MCU pin-related control, corresponding transistor drive, and then circuit conversion by relay groups composed of multiple relays. As long as you master this basic rule, you can check the circuit of all types of soymilk machines and eliminate all kinds of faults. However, the production of some models of circuit board is a bit problematic, it is to press the number of the component under the component, so only the component can be seen on the circuit board, but the component number can not be seen, so that the detection of the circuit is extremely inconvenient.

But generally speaking, the working principle of the soymilk machine and the juicer is different, and the soymilk machine cannot centrifuge at high speed at the same time as crushing and separate the juice, so the juice yield is not very high. If you use it yourself, you can buy it.

Nowadays, people's health awareness is still relatively high, and more families prefer to cook breakfast at home. Chinese especially like to drink soy milk, and there are soy milk machines on the market, which can make a variety of soy milk according to their own taste. There is a soymilk machine called fully automatic, how should the automatic soymilk machine be used?

What are the classifications of soymilk machines?

1. How to use the automatic soybean milk machine.

1. First of all, clean the soybeans, and it is best to soak them overnight in advance. As for the soaking time, only 6 hours of soaking is enough in summer, and it can be extended a little more in winter, about 10 hours.

2. Next, put the soaked beans into the soymilk machine barrel, and then add water, and the amount of water added needs to be controlled according to its highest water level, in short, it cannot exceed the highest water level. Because if it's high, there will be a problem of slurry.

4. Then turn on the power supply, the indicator light is on, and then press the start button again to directly adjust to the mode of soy milk. The automatic soymilk machine will start heating to complete the process of beating and heating. After ten minutes, the soymilk machine has finished its work, and then unplug the power supply, and a cup of beautiful soy milk is ready.

1. If you follow the grinding method, there is a mesh grinding, and there is a stainless steel grinder with holes. When soybeans are polished, they are sucked into the grinder to improve the efficiency of crushing. And after fine grinding processing, it is easier to digest and absorb lead imitation.

**It should be slightly higher, and it is inconvenient to clean it later because there are many dead ends.

2. There is also a kind of grinding without nets, there is no grinder on the outside of the cutter head, and the soybeans are poured directly into the cup and begin to be polished and heated. The main advantage is that it is easy to clean, and it is slightly lower, but the service life of the cutter head is relatively short.

Now there is a full-mold bucket automatic on the market'Soymilk machine, so how to use this automatic soymilk machine, I will introduce to you the use of automatic soymilk machine, welcome to read.

Step 1: Soak the beans, use the random dry bean measuring cup according to the 2 3 scale line to hold the dry beans and soak them in water, the soaking time is 8-16 hours in spring and autumn, 6-10 hours in summer, and 10-16 hours in winter. Warm special note:

Wash the beans before soaking them.

Step 2: Add beans and rice to the cup, measure the rice in the bean measuring cup according to the 2 3 scale, wash the soaked beans and put them directly into the cup.

Step 3This machine has the function of waterless anti-dry boiling, if there is no water in the cup or the water level is too low, the machine will not work, so as to ensure the safety of use.

Step 4:Fal mesh installation, take the Rafal mesh according to the installation indication arrow direction to install, Lafal mesh mouth and the head of the joint place should be tight and seamless, after the installation, pull down with your hand, Lafal mesh does not move, indicating that the installation is in place.

Step 5: Put the machine head into the cup according to the correct position, plug in the power cord, the power indicator light is on, press the "full nutrition soybean milk" health, the corresponding indicator light is on, and start the full nutrition soybean milk program.

Step 6: After heating and powering on, press the "Total Nutrient Soybean Milk" button, the electric heater will start heating, and after about 8 minutes (when using room temperature water), the water temperature will reach the temperature set by beating.

Step 7When the water temperature reaches the set temperature, the motor starts to work, and the motor drives the blade to beat twice, then heat to prevent overflow, and then beat three times.

Step 8: Anti-overflow cooking: After the soybean milk boils, the anti-overflow heating function of the machine will automatically start and enter the cooking process. The electric heater is heated intermittently to make the soybean milk boil repeatedly and fully cooked.

Step 9: Power-off alarm: After the work is over, the electric heater, motor and other components will automatically power off, and the machine will send out an audible and visual alarm to indicate that the soybean milk has been ready. After unplugging the power supply, you can prepare the soy milk for drinking.

In modern times, many office workers are in a hurry in the morning, therefore, in order to save time, many people use to buy automatic soymilk machines to make delicious and nutritious breakfasts, but before that, you have to know how to use it correctly, let's take a closer look: how to use the automatic soymilk machine and the precautions for the use of the automatic soymilk machine.

1. First of all, the beans should be soaked, but the time of soaking is not fixed, it is best to soak for 7-10 hours in summer, 9-13 hours in spring and autumn, and more than 10 hours in winter.

2. After soaking, put it into the machine.

3. Then, add some water to it, as for how much to add, it depends on the amount of beans and the size of the machine, if the water is too little, it will stop working, too much will overflow, therefore, it is best to be within the water line.

4. Then follow the direction of the arrow Rafal net. Its position should be tightly connected to the nose, without a slit, and it should be pulled down with water to see if it will move.

5. Put the machine head into the machine, then connect the power supply, wait for the light to turn on, press the start button, and wait for 10 minutes of heating, then it will start pulping.

6. After the pulp is beaten, it will automatically heat up until it is cooked.

7. Unplug when finished.

Precautions for the use of automatic soymilk machine:

1. When in use, its head cannot be watered, and when taking it out or putting it in, it must be disconnected from the power supply first.

2. When it is running, it should be kept out of the reach of children, and when it is made, the required materials should be put into the cup and the water should be added between the water line.

3. When dismantling the Rafal net, you must pay attention to the method, otherwise it is easy to get injured.

4. When it is running, it is best to keep a proper interval from the socket, so that it can be within its contact range and away from explosives.

5. When operating, you should choose the program corresponding to the eraser, so that you can make delicious things.

6. After use, clean it immediately.