e Surfing Broadband with TPLINK Infinity Router

In fact, you just follow the step-by-step operation, it's no problem at all, not used as a lot of settings, but many people just have problems, I also have a lot of people about this problem, learn to use search, much faster than waiting.

Here, you have to understand a little bit about the functions of wireless and wired routers, they are like electric plug boards, play a role in connectivity, router operation is done according to the manual, then the problem is in the connection line, the outside LAN network cable, or ** line with cat, it turned out to be directly connected to the computer, so now connect it to the router (which port to plug in, see the manual). Then connect a network cable from the router to the desktop computer, and the desktop computer is recommended to use a wired connection, because the wired will be a little more stable. Other wireless devices, such as laptops, mobile phones, tablets, etc., can be connected by searching for wifi, so that they can all access the Internet at the same time.

Remember, the computer doesn't have to dial anymore, because the router has already dialed for you, just like the mobile phone connection doesn't need to dial) If you say that the connection method you do is the same as I said, then reset the router (not restart, if not, check the manual) and then log in to the router again, fill in the Internet, set the connection password, nothing else need to be set, and then save.

1.First, disconnect the eSurfing gateway, connect the WiFi signal of the TP-Link router, log in to the router (, select the DHCP service, turn it off (select "Do Not Enable") and save;

2.Click "Setup Wizard", select "PPPoE (ADSL Virtual Dialing)", and then click Next;

3.Then enter your Internet password and password (that is, the password given to you by the operator when you turn on the broadband);

<>5.After saving the file roll, take a network cable and connect it to the "Gigabit Port" connected to the Tianyi gateway;

6.Finally, the other end of the network cable is connected to the "LAN port" of the router without line answer, and the telecom Tianyi router and TP-Link are successfully bridged.

Hello dear users!

First of all, go to the TP-Link official website to set up the wireless router ( Set up the broadband account and password, select automatic dialing, and connect to China Telecom's dialer modem, you can use it. (wifi included).

Xiaomi Mi 2 is crazy! Inch large screen to enjoy quad-core 8 million pixels front and rear dual cameras android super cost-effective The second batch of 1000 units has been sold out The third batch of 1000 units is arriving one after another, first come, first served! (2399 yuan of phone bills for the purchase of new users, plus 300 yuan of phone bills for new users).

You look at your tp-link manual. It's simple. Or you can give the telecom ** and ask the engineer to get it for you.

1. Enter the settings interface of the main router, then click [Running Status] in the left option bar, and you can find the DNS server in the WAN port status bar, there are two in total, the primary DNS and the alternative DNS server, record them.

2. Set the SSID to TP Link A. Set the wireless channel to: 11.

Note: The WDS or Bridge feature must be turned off. Click [DHCP Server] --DHC Server Settings] and set [Address Pool Start Address] to; Set the End Address of the Address Pool to Click Save to restart the main router.

The main router is set up.

1.First, disconnect the eSurfing gateway, connect the WiFi signal of the TP-Link router, log in to the router (, select the DHCP service, turn it off (select "Do Not Enable") and save;

2.Click "Setup Wizard", select "PPPoE (ADSL Virtual Dialing)", and then click Next;

3.Then enter your Internet password and password (that is, the account number and password given to you by the operator when you turn on the broadband);

5.After saving, take a network cable and connect it to the "Gigabit Port" connected to the Tianyi gateway;

6.Finally, the other end of the network cable is connected to the "LAN port" of the infinite router, and the telecom Tianyi router and TP-link are successfully bridged.

There are a lot of things on the Internet about cracking the Tianyi route. Two days ago, I installed Tianyi 4mb broadband, routing, and the cat was all bought by myself.

Telecom Tianyi has its own dialing software, and it is not good to set up the route. Finally, spend 50 yuan to ask someone to set it up. He didn't do anything with Ben.

That is, the local connection is adjusted to the automatic IP. Deleted some unwanted agreements and services. Routes are set as usual. ADLS dials in the account number and password.

One of the key keys is here. It's 10,000. Directly ask the waiter to say don't Tianyi's with software. Directly ask for the software that comes with the system.

After the two. ok。Cause. The software password that comes with eSurfing is over-encrypted. The waiter number 10000 unlocks your encryption. Router no matter what you are.

Any model can be used. Those on the Internet also have broken this software, or superuser password rerouting. or sock5** server, without a certain computer level. I can't find the north with Ben. I also found a good crack software on the Internet, but it turned out to be poisoned, and the passwords were all lost. Call 10000 to get it back. Hope the above works for you.